If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Pulsating brake pedal
I just replaced the front brake pads in my car. I did not replace nor
resurface the rotors. Now the brake pedal is pulsating/vibrating everytime I apply the brakes. This is more noticeable at high speeds. Can someone offer any suggestions as to why this may be happening? My understanding is that if the brake pedal pulsates and the steering vibrates while braking, then this indicates bad rotors. But in my case the steering wheel *does not* vibrate, its only the brake pedal that is pulsating. I also read somewhere that another cause for this could be the rear brakes. I had replaced my rear brake pads about 6-9 months ago (didn't resurface the rear rotors, just replaced pads). So my rear brakes should be good. My brake pedal was not pulsating prior to replacing the front pads. Your inputs are appreciated. Thanks, Mark |
Ads |
#2
|
|||
|
|||
sounds like a warped rotor, suggest having them turned.
|
#3
|
|||
|
|||
Mark wrote: > My brake pedal was not pulsating prior to > replacing the front pads. Did you remove the rotors from their hub during the procedure or let them "fall away" from the hub while replacing the pads? You may have had rust particles come loose from the rotor and get jammed between the rotor and hub causing it to not seat squarely -- hence the magical new vibration. Likewise the rotor could simply not be fully seated (cocked) which can be a very dangerous safety issue. Or you could have removed the rotor and installed it in a different position index as referenced to the hub -- stacked run-out tolerances could be worse now than in the original position. Or you could have overtightened or unevenly tightened the lugnuts. If you were to mention your year, make, and model then more specific experience based answers might come of it. Toyota MDT in MO |
#4
|
|||
|
|||
If you got the wheel lug nuts on at different torques, that can cause
the rotors to warp and the pedal to pulse. With most of the cheap rotors these days, you really need a hand torque wrench to put the wheels on or you end up with problems. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Mark wrote: > > I just replaced the front brake pads in my car. I did not replace nor > resurface the rotors. Now the brake pedal is pulsating/vibrating > everytime I apply the brakes. This is more noticeable at high speeds. > Can someone offer any suggestions as to why this may be happening? My > understanding is that if the brake pedal pulsates and the steering > vibrates while braking, then this indicates bad rotors. But in my case > the steering wheel *does not* vibrate, its only the brake pedal that is > pulsating. > > I also read somewhere that another cause for this could be the rear > brakes. I had replaced my rear brake pads about 6-9 months ago (didn't > resurface the rear rotors, just replaced pads). So my rear brakes > should be good. My brake pedal was not pulsating prior to replacing the > front pads. > > Your inputs are appreciated. > Thanks, > Mark |
#5
|
|||
|
|||
Comboverfish wrote:
> > > Mark wrote: > > My brake pedal was not pulsating prior to > > replacing the front pads. > > Did you remove the rotors from their hub during the procedure or let > them "fall away" from the hub while replacing the pads? > > You may have had rust particles come loose from the rotor and get > jammed between the rotor and hub causing it to not seat squarely -- > hence the magical new vibration. Likewise the rotor could simply not > be fully seated (cocked) which can be a very dangerous safety issue. > > Or you could have removed the rotor and installed it in a different > position index as referenced to the hub -- stacked run-out tolerances > could be worse now than in the original position. > > Or you could have overtightened or unevenly tightened the lugnuts. > > If you were to mention your year, make, and model then more specific > experience based answers might come of it. > > Toyota MDT in MO http://www.babcox.com/editorial/bf/bf100326.htm |
#6
|
|||
|
|||
"Mike Romain" > wrote in message ... > If you got the wheel lug nuts on at different torques, that can cause > the rotors to warp and the pedal to pulse. With most of the cheap > rotors these days, you really need a hand torque wrench to put the > wheels on or you end up with problems. > > Mike You can say that again. Some are extremely sensitive. I had my tires rotated not long ago at a wellknown national Discount Tire store. They claim to use torque stick impact wrenches just to run up the lug nuts, and then take them the rest of the way by hand. I watched as they did it, actually, and thought this might be an okay way to do it. It wasn't. Rotors warped very quickly. If those torque sticks allow overtorqueing to begin with, then the kid pulling the manual torque wrench is unlikely to notice the problem. I learned another good lesson that day. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Hard Brake Pedal when cold | Hamish WAUGH | Technology | 4 | February 1st 05 01:18 PM |
Simultaneous Application of Gas and Brake Pedals | KaWallski | Chrysler | 0 | January 29th 05 02:40 AM |
Brake Pedal Fade | DavidB | Honda | 3 | December 28th 04 06:21 AM |
e36 brake pedal resistance begins in diff points | Steve Sousa | BMW | 6 | December 15th 04 06:12 PM |
new 04 accord pulsing brake pedal | chuck smoko | Honda | 8 | December 11th 04 01:11 AM |