If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Torsion tool for spring plates
I know this sounds silly, but what is the proper way to use this? I was
looking on the net, and saw some pics of one guy resting it on the ground and and pushing the spring plates up with it http://www.vwtrendsweb.com/tech/0312vwt_71super/ , and another how-to page (http://www.bajas.8m.com/torsion.htm) showed the top of it resting on the chassis or body somewhere, and then the screwing it up, pushing the spring plate up. Just a curiosity, since I'm gonna change out my spring plate bushings this weekend, and I have one of these tools. Or would I be better off using a chain and floor jack?? Thanks for any assistance! Dane '69 Bug '63 Bug |
Ads |
#2
|
|||
|
|||
topside of the tool usually has a sort of cup that faces downward which fits
over the bodybolt (mounts to shock tower) found up in the fenderwell. You just put the plate between the slots on the bottom part of the tool and start screwing. Once your sitting in front of the rear assy with the tool in your hand, it should become pretty apparent. sometimes the large wingnut can be a pain, I keep a same sized nut and wrench close depening on bigger bars or if I am raising the car for for offroad. Mark Detro Englewood, FL |
#3
|
|||
|
|||
When I replaced my torsion bars and what not I used the chain and jack
method with no trouble. Just be sure to set it up with no slack in the chain or the car will rise as the jack is applied. If you have to, put a piece of plywood under the jack to make up the distance if the jack floats. You want the jack to be stable on the ground! Use a large chain those torsion bars are tough! Be sure to check the car for level when done. Use a magnetic angle guage to ensure the starting angles (preload) are the same and then check the level with the weight of the vehicle after. You will need to allow the car to roll a few feet to ensure the wheels are at a natural stance. Good luck John "Dane Tyler" > wrote in message ... >I know this sounds silly, but what is the proper way to use this? I was >looking on the net, and saw some pics of one guy resting it on the ground >and and pushing the spring plates up with it >http://www.vwtrendsweb.com/tech/0312vwt_71super/ , and another how-to page >(http://www.bajas.8m.com/torsion.htm) showed the top of it resting on the >chassis or body somewhere, and then the screwing it up, pushing the spring >plate up. Just a curiosity, since I'm gonna change out my spring plate >bushings this weekend, and I have one of these tools. Or would I be better >off using a chain and floor jack?? > > Thanks for any assistance! > > Dane > '69 Bug > '63 Bug > |
#4
|
|||
|
|||
>When I replaced my torsion bars and what not I used the chain and jack
>method with no trouble I use one of the strut spring compressor tools with one bolt in the shock tower and one on the spring plate. This makes the job real easy nothing that can slip or get in the way, and no chance of the car raising. Mario |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
why do people pay for these plates??? | AZGuy | Driving | 8 | January 20th 05 02:41 PM |
Torsion Bars | 94 Dakota | Dodge | 2 | October 21st 04 10:51 PM |
License Plates - Antiques, porcelains. many more | PL8Seditor | Antique cars | 0 | January 26th 04 12:54 AM |