A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Corvette
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

'Hockey Puck" a Corvette



 
 
Thread Tools Display Modes
  #1  
Old December 23rd 04, 05:21 AM
Jim M
external usenet poster
 
Posts: n/a
Default 'Hockey Puck" a Corvette

Hey there,

Again with my 1977 Vette.....BTW... I did all the brake calipers and
brake shoes etc.... job went without a hitch. The new timing chain, water
pump and entire front end is totally sealed and running fine with no leaks.

My next personal fix is to look at the rear leaf spring as the rear
wheels are sagging somewhat (very little really).. I was told by a buddy in
my corvette club that a person could get another year out of their sagging
rear leaf spring by drilling through two (Canadian eh) hockey pucks and
could be used as spacers....one on each end of the spring (drivers and
passenger side) to lift the car to make up for the sag.
I personally think this is kind of a radical type surgery but thought I
would throw this out to the corvette gurus out there.
Since we have a Hockey strike here in Canada...maybe I have a new market
for hockey pucks!.... Thoughts?

Thanks....Jim


Ads
  #2  
Old December 23rd 04, 08:18 AM
Tom in Missouri
external usenet poster
 
Posts: n/a
Default

Quite often, the "sag" is normal. Check the heights in the service manual
to see if you are really sagging or not.

Even then, if you are, you may find that it is a matter of the bushings at
the spring ends to the bolts have mashed flatter than when new. Basically,
the hockey pucks are just acting like slightly thicker bushings.


"Jim M" <jim> wrote in message ...
> Hey there,
>
> Again with my 1977 Vette.....BTW... I did all the brake calipers and
> brake shoes etc.... job went without a hitch. The new timing chain, water
> pump and entire front end is totally sealed and running fine with no

leaks.
>
> My next personal fix is to look at the rear leaf spring as the rear
> wheels are sagging somewhat (very little really).. I was told by a buddy

in
> my corvette club that a person could get another year out of their sagging
> rear leaf spring by drilling through two (Canadian eh) hockey pucks and
> could be used as spacers....one on each end of the spring (drivers and
> passenger side) to lift the car to make up for the sag.
> I personally think this is kind of a radical type surgery but thought

I
> would throw this out to the corvette gurus out there.
> Since we have a Hockey strike here in Canada...maybe I have a new

market
> for hockey pucks!.... Thoughts?
>
> Thanks....Jim
>
>


  #3  
Old December 23rd 04, 08:18 AM
Tom in Missouri
external usenet poster
 
Posts: n/a
Default

Quite often, the "sag" is normal. Check the heights in the service manual
to see if you are really sagging or not.

Even then, if you are, you may find that it is a matter of the bushings at
the spring ends to the bolts have mashed flatter than when new. Basically,
the hockey pucks are just acting like slightly thicker bushings.


"Jim M" <jim> wrote in message ...
> Hey there,
>
> Again with my 1977 Vette.....BTW... I did all the brake calipers and
> brake shoes etc.... job went without a hitch. The new timing chain, water
> pump and entire front end is totally sealed and running fine with no

leaks.
>
> My next personal fix is to look at the rear leaf spring as the rear
> wheels are sagging somewhat (very little really).. I was told by a buddy

in
> my corvette club that a person could get another year out of their sagging
> rear leaf spring by drilling through two (Canadian eh) hockey pucks and
> could be used as spacers....one on each end of the spring (drivers and
> passenger side) to lift the car to make up for the sag.
> I personally think this is kind of a radical type surgery but thought

I
> would throw this out to the corvette gurus out there.
> Since we have a Hockey strike here in Canada...maybe I have a new

market
> for hockey pucks!.... Thoughts?
>
> Thanks....Jim
>
>


  #4  
Old December 23rd 04, 03:31 PM
Bob G.
external usenet poster
 
Posts: n/a
Default

On Thu, 23 Dec 2004 07:18:34 GMT, "Tom in Missouri" >
wrote:

>Quite often, the "sag" is normal. Check the heights in the service manual
>to see if you are really sagging or not.
>
>Even then, if you are, you may find that it is a matter of the bushings at
>the spring ends to the bolts have mashed flatter than when new. Basically,
>the hockey pucks are just acting like slightly thicker bushings.
>


Tom is correct....(As always..and I am serious the guy knows his
:stuff" )

.. But if you are going to go thru all that trouble...be advised that a
new Steel rear spring retails for only about 100 bucks ..just seems to
me that you may just want to replace it since you will have everything
apart anyhow...

I keep telling myself its only money....lol...

Bob Griffiths
64 72 76 79 & 95
68 Chevelle
..





  #5  
Old December 23rd 04, 03:31 PM
Bob G.
external usenet poster
 
Posts: n/a
Default

On Thu, 23 Dec 2004 07:18:34 GMT, "Tom in Missouri" >
wrote:

>Quite often, the "sag" is normal. Check the heights in the service manual
>to see if you are really sagging or not.
>
>Even then, if you are, you may find that it is a matter of the bushings at
>the spring ends to the bolts have mashed flatter than when new. Basically,
>the hockey pucks are just acting like slightly thicker bushings.
>


Tom is correct....(As always..and I am serious the guy knows his
:stuff" )

.. But if you are going to go thru all that trouble...be advised that a
new Steel rear spring retails for only about 100 bucks ..just seems to
me that you may just want to replace it since you will have everything
apart anyhow...

I keep telling myself its only money....lol...

Bob Griffiths
64 72 76 79 & 95
68 Chevelle
..





  #6  
Old December 23rd 04, 05:11 PM
Jim M
external usenet poster
 
Posts: n/a
Default

Okay, Thanks again guys...my manual doesn't give any proper heights...so am
going to search the web for these heights. If a hockey puck type bushing is
all I need, I think I will put them in just to last one more summer. Thanks
again. Jim


"Bob G." > wrote in message
...
> On Thu, 23 Dec 2004 07:18:34 GMT, "Tom in Missouri" >
> wrote:
>
>>Quite often, the "sag" is normal. Check the heights in the service manual
>>to see if you are really sagging or not.
>>
>>Even then, if you are, you may find that it is a matter of the bushings at
>>the spring ends to the bolts have mashed flatter than when new.
>>Basically,
>>the hockey pucks are just acting like slightly thicker bushings.
>>

>
> Tom is correct....(As always..and I am serious the guy knows his
> :stuff" )
>
> . But if you are going to go thru all that trouble...be advised that a
> new Steel rear spring retails for only about 100 bucks ..just seems to
> me that you may just want to replace it since you will have everything
> apart anyhow...
>
> I keep telling myself its only money....lol...
>
> Bob Griffiths
> 64 72 76 79 & 95
> 68 Chevelle
> .
>
>
>
>
>



  #7  
Old December 23rd 04, 05:11 PM
Jim M
external usenet poster
 
Posts: n/a
Default

Okay, Thanks again guys...my manual doesn't give any proper heights...so am
going to search the web for these heights. If a hockey puck type bushing is
all I need, I think I will put them in just to last one more summer. Thanks
again. Jim


"Bob G." > wrote in message
...
> On Thu, 23 Dec 2004 07:18:34 GMT, "Tom in Missouri" >
> wrote:
>
>>Quite often, the "sag" is normal. Check the heights in the service manual
>>to see if you are really sagging or not.
>>
>>Even then, if you are, you may find that it is a matter of the bushings at
>>the spring ends to the bolts have mashed flatter than when new.
>>Basically,
>>the hockey pucks are just acting like slightly thicker bushings.
>>

>
> Tom is correct....(As always..and I am serious the guy knows his
> :stuff" )
>
> . But if you are going to go thru all that trouble...be advised that a
> new Steel rear spring retails for only about 100 bucks ..just seems to
> me that you may just want to replace it since you will have everything
> apart anyhow...
>
> I keep telling myself its only money....lol...
>
> Bob Griffiths
> 64 72 76 79 & 95
> 68 Chevelle
> .
>
>
>
>
>



 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Corvette magazines for sale Ruper 74 Corvette 2 December 20th 04 03:13 PM
inexpensive CORVETTE collectable Hugh Comstock Corvette 0 October 6th 04 07:24 PM
FS: "Corvette Evolution 1953-1986" Litho Sheet J.R. Sinclair Corvette 0 August 11th 04 07:30 AM


All times are GMT +1. The time now is 02:12 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.