If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
FS: AMC 304 Engines and Parts
I am selling two AMC 304's. One has popped. Piston shattered but there
appears to be no apparent scoring on cylinder wall. This engine had about 30K on reman. It was running in my jeep till then. The other has about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was running in my jeep till I swapped for the other. this engine had some blow by on the #1 cylinder that is all. I have all stock parts to build one of these but exhaust manifold. On top of that, I have a brand new with only 15 minutes of run time, AMC performer intake (NON EGR) and a brand new Edelbrock 1406 carb for this engine. This intake has everything on it from the stock manifold and is ready to bolt on. I am keeping my fan, but everything else should be there. Comes with altenator, and power steering pump as well. Started I used as a core charge for the 350 starter I bought for the swap I just did. Comes with bell housing as well. The two engines with stock parts I will sell for $175, and the upgrades which include the carb, intake and a set of inframe hedman hedders will sell for $450. The hedders are not the coated ones so they rust, but are in great shape. Not bent, dinged or warped. If somone wants all of it, I will let it go for $600. The blown engine is not in a crate with one head off, but it is garaged, the other block is in a crate that has been covered and oiled. Email me at if you are interested in any or all of this. Thanks so much. |
Ads |
#3
|
|||
|
|||
FS: AMC 304 Engines and Parts
Everything is located at Lake Anna, VA.
RoyJ wrote: > And where is all this located? > > wrote: > > > I am selling two AMC 304's. One has popped. Piston shattered but there > > appears to be no apparent scoring on cylinder wall. This engine had > > about 30K on reman. It was running in my jeep till then. The other has > > about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was > > running in my jeep till I swapped for the other. this engine had some > > blow by on the #1 cylinder that is all. I have all stock parts to build > > one of these but exhaust manifold. On top of that, I have a brand new > > with only 15 minutes of run time, AMC performer intake (NON EGR) and a > > brand new Edelbrock 1406 carb for this engine. This intake has > > everything on it from the stock manifold and is ready to bolt on. I am > > keeping my fan, but everything else should be there. Comes with > > altenator, and power steering pump as well. Started I used as a core > > charge for the 350 starter I bought for the swap I just did. Comes with > > bell housing as well. The two engines with stock parts I will sell for > > $175, and the upgrades which include the carb, intake and a set of > > inframe hedman hedders will sell for $450. The hedders are not the > > coated ones so they rust, but are in great shape. Not bent, dinged or > > warped. If somone wants all of it, I will let it go for $600. The blown > > engine is not in a crate with one head off, but it is garaged, the > > other block is in a crate that has been covered and oiled. Email me at > > if you are interested in any or all of this. > > > > Thanks so much. > > |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
AWA [DEMAND] engines for pumps | [email protected] | General | 1 | February 22nd 06 04:44 PM |
AWA [DEMAND] Used & new GM parts wanted! | [email protected] | General | 0 | November 29th 05 08:51 PM |
AWA [OFFER] Like new factory dressed and takeout engines | [email protected] | General | 0 | November 22nd 05 11:01 AM |
F.S. RUST FREE 80's BLAZER,PICKUP PARTS, in NH, ME (Military) | MilitaryTruckParts | 4x4 | 2 | March 27th 04 05:49 PM |