A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » VW water cooled
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Research Qs on my 91 16V AT valve body....LONG and semi-Technical



 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #1  
Old March 13th 05, 07:36 PM
One out of many daves
external usenet poster
 
Posts: n/a
Default Research Qs on my 91 16V AT valve body....LONG and semi-Technical

First off........is anyone selling an automatic transmission valve body for
me to examine? <g>

How much power is supplied to the solenoids and AT fluid temperature inside
of the transmission?
Is it possible to activate the solenoids at the valve body's wiring plug
with an external power supply to check the operation of the individual
solenoids?

From my testing of the wiring, I did a test of the valve body wiring at the
transmission plug.
I got a slightly high reading of 70 and 68 Ohms for Solenoids #2 and #4
(should be 55-65 Ohms)
I will also have to recheck #6 solenoid and I wonder why it uses a different
power supply pin from everything else inside of the valve body even the AT
fluid temp sensor. AND THAT IS THE ONLY SOLENOID NOT CREATING A DTC.
Is this correct??? I kinda want to imagine what is happening before I pull
out the valve body.

(Total of 10 pins/terminals at the Valve Body Wiring Plug)

Solenoids
1-TCM pin 22
2-TCM pin 23
3-TCM pin 3
4-TCM pin 2
5-TCM pin 24
6-TCM pin 25
7-TCM pin 21

1 pin - ATF temperature sensor uses TCM pins 30 +31 (TCM pin 31 is not
recorded in the Bentley wiring diagram)
2 pins used for power supply at the Valve Body Wiring Plug both originate
from TCM pin 18
(#6 solenoid uses 1 of the these pins, while all the other solenoids
and temperature sensor uses the other)
TCM pin 18 supplies the power to the solenoids and the other pins ground
them out as needed.

Here are the results of my DTCs that force my trans to be put in 3H (Limp
Mode)

VAG-COM Version: Release 303.1

Control Module Part Number: 096 927 731 M
Component and/or Version: DIGIMAT 0811
Software Coding: Diagnose VW
Work Shop Code:
7 Faults Found:
00258 - Solenoid Valve 1 (N88)
36-00 - Open Circuit
00260 - Solenoid Valve 2 (N89)
36-00 - Open Circuit
00262 - Solenoid Valve 3 (N90)
36-00 - Open Circuit
00264 - Solenoid Valve 4 (N91)
36-00 - Open Circuit
00266 - Solenoid Valve 5 (N92)
36-00 - Open Circuit
00270 - Solenoid Valve 7 (N94)
36-00 - Open Circuit
00300 - Transmission Fluid Temp. Sensor (G93)
34-00 - No Malfunction Detected


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
lookin 4 butch VW air cooled 12 December 16th 04 11:38 PM
New valve body part number for infamous transaxle problems at twice the cost John Hupp Saturn 3 December 8th 04 04:04 PM
93 SL1 Valve Body - Question Gary Compton Saturn 3 September 3rd 04 05:58 PM
Transmission Shifts Hard - Valve Body? Gary Compton Saturn 8 August 21st 04 07:04 PM


All times are GMT +1. The time now is 06:16 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.