If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
96 intrepid rear drum brakes
What size nut holds on the back brake hub on a
1996 Intrepid? I thought it was a 34mm deep socket but it seems bigger than that. Thanks for any help. |
Ads |
#2
|
|||
|
|||
96 intrepid rear drum brakes
den630 wrote:
> What size nut holds on the back brake hub on a > 1996 Intrepid? I thought it was a 34mm deep socket > but it seems bigger than that. Thanks for any help. > > According to this thread (has what appears to be the procedure out of the FSM) on DI.net: http://www.dodgeintrepid.net/forums/...rum+nut+siz e some guy used a 1-7/8" socket, which, if correct, would translate into either a 47 or 48mm. Torque would be 124 ft-lbs. Bill Putney (To reply by e-mail, replace the last letter of the alphabet in my address with the letter 'x') |
#3
|
|||
|
|||
96 intrepid rear drum brakes
"Bill Putney" > wrote in message ... > den630 wrote: > > What size nut holds on the back brake hub on a > > 1996 Intrepid? I thought it was a 34mm deep socket > > but it seems bigger than that. Thanks for any help. > > > > > According to this thread (has what appears to be the procedure out of > the FSM) on DI.net: > http://www.dodgeintrepid.net/forums/...rum+nut+siz e > some guy used a 1-7/8" socket, which, if correct, would translate into > either a 47 or 48mm. Torque would be 124 ft-lbs. > > Bill Putney > (To reply by e-mail, replace the last letter of the alphabet in my > address with the letter 'x') Thanks Bill I didn't even know that there was a www.dodgeintrepid.net web site. There is allot of good information on the site. Thanks again Den |
#4
|
|||
|
|||
96 intrepid rear drum brakes
den630 wrote:
> "Bill Putney" > wrote in message > ... > >>den630 wrote: >> >>>What size nut holds on the back brake hub on a >>>1996 Intrepid? I thought it was a 34mm deep socket >>>but it seems bigger than that. Thanks for any help. >>> >>> >> >>According to this thread (has what appears to be the procedure out of >>the FSM) on DI.net: >> > > http://www.dodgeintrepid.net/forums/...rum+nut+siz e > >>some guy used a 1-7/8" socket, which, if correct, would translate into >>either a 47 or 48mm. Torque would be 124 ft-lbs. >> >>Bill Putney >>(To reply by e-mail, replace the last letter of the alphabet in my >> address with the letter 'x') > > > Thanks Bill I didn't even know that there was a www.dodgeintrepid.net web > site. There is allot of > good information on the site. > Thanks again > Den You're welcome! Bill Putney (To reply by e-mail, replace the last letter of the alphabet in my address with the letter 'x') |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
type 3 to type 1 rear brakes | george taylor | VW air cooled | 1 | May 4th 06 03:28 AM |
99 Accord noise in Right Rear brakes | Honda | 2 | March 14th 05 03:23 AM | |
97 ford escort, weak rear brakes | imnoldee | Technology | 2 | December 28th 04 12:00 PM |
2000 dodge stratus rear brakes | BRIAN | Dodge | 0 | September 28th 04 09:18 AM |