If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Run Flat tire question
Found a nail in the tread portion on one of my Goodyear Run Flat tires.
Once removed, is this something that can be plugged, without harming the tire pressure sensor? Any thing special I need to know about repairing the tire before I remove the nail? |
Ads |
#2
|
|||
|
|||
"H and A" > wrote in message
news > Found a nail in the tread portion on one of my Goodyear Run Flat tires. > Once removed, is this something that can be plugged, without harming the > tire pressure sensor? Any thing special I need to know about repairing > the tire before I remove the nail? Unless you plan on replacing it very soon plugging it is not the answer. To continue to use the tire you need to plug and then patch from the inside. The patch is to contain the air and the plug is to stop the migration of water and other fine trash from breaking the patch seal. You should not be able to damage the pressure sensor by plugging the tire, it is about the size of an old Zippo lighter and attached to the valve stem. The only warnings I've heard on them being damaged is the use of "Fix-A-Flat" or tire removal by an incompetent tire repair shop. Dally Tire a Goodyear dealer in Coldwater Mi. charged $10 to repair a tire, Capitol Tire in Toledo got me for $56 just to mount one, a Goodyear dealer that will never see me again. Plus I would like for them to get all of the attention that I paid for by passing this on to everyone. -- Dad 05 C6 Silver/Red 6spd Z51 72 Shark Black/Black/4spd |
#3
|
|||
|
|||
"H and A" > wrote in message
news > Found a nail in the tread portion on one of my Goodyear Run Flat tires. > Once removed, is this something that can be plugged, without harming the > tire pressure sensor? Any thing special I need to know about repairing > the tire before I remove the nail? Unless you plan on replacing it very soon plugging it is not the answer. To continue to use the tire you need to plug and then patch from the inside. The patch is to contain the air and the plug is to stop the migration of water and other fine trash from breaking the patch seal. You should not be able to damage the pressure sensor by plugging the tire, it is about the size of an old Zippo lighter and attached to the valve stem. The only warnings I've heard on them being damaged is the use of "Fix-A-Flat" or tire removal by an incompetent tire repair shop. Dally Tire a Goodyear dealer in Coldwater Mi. charged $10 to repair a tire, Capitol Tire in Toledo got me for $56 just to mount one, a Goodyear dealer that will never see me again. Plus I would like for them to get all of the attention that I paid for by passing this on to everyone. -- Dad 05 C6 Silver/Red 6spd Z51 72 Shark Black/Black/4spd |
#4
|
|||
|
|||
Can you really trust a "repaired" tyre, especially at high speed.....
"Dad" > wrote in message ... > "H and A" > wrote in message > news >> Found a nail in the tread portion on one of my Goodyear Run Flat tires. >> Once removed, is this something that can be plugged, without harming the >> tire pressure sensor? Any thing special I need to know about repairing >> the tire before I remove the nail? > Unless you plan on replacing it very soon plugging it is not the answer. > To continue to use the tire you need to plug and then patch from the > inside. The patch is to contain the air and the plug is to stop the > migration of water and other fine trash from breaking the patch seal. You > should not be able to damage the pressure sensor by plugging the tire, it > is about the size of an old Zippo lighter and attached to the valve stem. > The only warnings I've heard on them being damaged is the use of > "Fix-A-Flat" or tire removal by an incompetent tire repair shop. Dally > Tire a Goodyear dealer in Coldwater Mi. charged $10 to repair a tire, > Capitol Tire in Toledo got me for $56 just to mount one, a Goodyear dealer > that will never see me again. Plus I would like for them to get all of the > attention that I paid for by passing this on to everyone. > -- > Dad > 05 C6 Silver/Red 6spd Z51 > 72 Shark Black/Black/4spd > |
#5
|
|||
|
|||
Can you really trust a "repaired" tyre, especially at high speed.....
"Dad" > wrote in message ... > "H and A" > wrote in message > news >> Found a nail in the tread portion on one of my Goodyear Run Flat tires. >> Once removed, is this something that can be plugged, without harming the >> tire pressure sensor? Any thing special I need to know about repairing >> the tire before I remove the nail? > Unless you plan on replacing it very soon plugging it is not the answer. > To continue to use the tire you need to plug and then patch from the > inside. The patch is to contain the air and the plug is to stop the > migration of water and other fine trash from breaking the patch seal. You > should not be able to damage the pressure sensor by plugging the tire, it > is about the size of an old Zippo lighter and attached to the valve stem. > The only warnings I've heard on them being damaged is the use of > "Fix-A-Flat" or tire removal by an incompetent tire repair shop. Dally > Tire a Goodyear dealer in Coldwater Mi. charged $10 to repair a tire, > Capitol Tire in Toledo got me for $56 just to mount one, a Goodyear dealer > that will never see me again. Plus I would like for them to get all of the > attention that I paid for by passing this on to everyone. > -- > Dad > 05 C6 Silver/Red 6spd Z51 > 72 Shark Black/Black/4spd > |
#6
|
|||
|
|||
Can you, yes, can I, no! A properly repaired tire can run many miles but not
with me in the car at high speeds. For a few hundred dollars it's not even a consideration. If I have a tire problem on the expressway/carriageway I'll sacrifice the tire and rim to make it to a safe pull off road/exit. So my tires will be the tires that are not patched/plugged, no question. There are two reasons to stop on a expressway/carriageway, you can't go any further, (stopped engine or stopped traffic), or some policeman wants to risk his life to give me a ticket. -- Dad 05 C6 Silver/Red 6spd Z51 72 Shark Black/Black/4spd "C5Guy" > wrote in message ... > Can you really trust a "repaired" tyre, especially at high speed..... > > "Dad" > wrote in message > ... >> "H and A" > wrote in message >> news >>> Found a nail in the tread portion on one of my Goodyear Run Flat tires. >>> Once removed, is this something that can be plugged, without harming the >>> tire pressure sensor? Any thing special I need to know about repairing >>> the tire before I remove the nail? >> Unless you plan on replacing it very soon plugging it is not the answer. >> To continue to use the tire you need to plug and then patch from the >> inside. The patch is to contain the air and the plug is to stop the >> migration of water and other fine trash from breaking the patch seal. > > |
#7
|
|||
|
|||
Can you, yes, can I, no! A properly repaired tire can run many miles but not
with me in the car at high speeds. For a few hundred dollars it's not even a consideration. If I have a tire problem on the expressway/carriageway I'll sacrifice the tire and rim to make it to a safe pull off road/exit. So my tires will be the tires that are not patched/plugged, no question. There are two reasons to stop on a expressway/carriageway, you can't go any further, (stopped engine or stopped traffic), or some policeman wants to risk his life to give me a ticket. -- Dad 05 C6 Silver/Red 6spd Z51 72 Shark Black/Black/4spd "C5Guy" > wrote in message ... > Can you really trust a "repaired" tyre, especially at high speed..... > > "Dad" > wrote in message > ... >> "H and A" > wrote in message >> news >>> Found a nail in the tread portion on one of my Goodyear Run Flat tires. >>> Once removed, is this something that can be plugged, without harming the >>> tire pressure sensor? Any thing special I need to know about repairing >>> the tire before I remove the nail? >> Unless you plan on replacing it very soon plugging it is not the answer. >> To continue to use the tire you need to plug and then patch from the >> inside. The patch is to contain the air and the plug is to stop the >> migration of water and other fine trash from breaking the patch seal. > > |
#8
|
|||
|
|||
I'm with you dad.....i'd rather be sure I'd got a good set of boots when
that dick/drunk/drug/sleeping driver decides to change lanes just as I approach......cost of 4 tyres versus life....no brainer "Dad" > wrote in message ... > Can you, yes, can I, no! A properly repaired tire can run many miles but > not with me in the car at high speeds. For a few hundred dollars it's not > even a consideration. If I have a tire problem on the > expressway/carriageway I'll sacrifice the tire and rim to make it to a > safe pull off road/exit. So my tires will be the tires that are not > patched/plugged, no question. There are two reasons to stop on a > expressway/carriageway, you can't go any further, (stopped engine or > stopped traffic), or some policeman wants to risk his life to give me a > ticket. > -- > Dad > 05 C6 Silver/Red 6spd Z51 > 72 Shark Black/Black/4spd > "C5Guy" > wrote in message > ... >> Can you really trust a "repaired" tyre, especially at high speed..... >> >> "Dad" > wrote in message >> ... >>> "H and A" > wrote in message >>> news >>>> Found a nail in the tread portion on one of my Goodyear Run Flat tires. >>>> Once removed, is this something that can be plugged, without harming >>>> the tire pressure sensor? Any thing special I need to know about >>>> repairing the tire before I remove the nail? >>> Unless you plan on replacing it very soon plugging it is not the answer. >>> To continue to use the tire you need to plug and then patch from the >>> inside. The patch is to contain the air and the plug is to stop the >>> migration of water and other fine trash from breaking the patch seal. > >> > > |
#9
|
|||
|
|||
I'm with you dad.....i'd rather be sure I'd got a good set of boots when
that dick/drunk/drug/sleeping driver decides to change lanes just as I approach......cost of 4 tyres versus life....no brainer "Dad" > wrote in message ... > Can you, yes, can I, no! A properly repaired tire can run many miles but > not with me in the car at high speeds. For a few hundred dollars it's not > even a consideration. If I have a tire problem on the > expressway/carriageway I'll sacrifice the tire and rim to make it to a > safe pull off road/exit. So my tires will be the tires that are not > patched/plugged, no question. There are two reasons to stop on a > expressway/carriageway, you can't go any further, (stopped engine or > stopped traffic), or some policeman wants to risk his life to give me a > ticket. > -- > Dad > 05 C6 Silver/Red 6spd Z51 > 72 Shark Black/Black/4spd > "C5Guy" > wrote in message > ... >> Can you really trust a "repaired" tyre, especially at high speed..... >> >> "Dad" > wrote in message >> ... >>> "H and A" > wrote in message >>> news >>>> Found a nail in the tread portion on one of my Goodyear Run Flat tires. >>>> Once removed, is this something that can be plugged, without harming >>>> the tire pressure sensor? Any thing special I need to know about >>>> repairing the tire before I remove the nail? >>> Unless you plan on replacing it very soon plugging it is not the answer. >>> To continue to use the tire you need to plug and then patch from the >>> inside. The patch is to contain the air and the plug is to stop the >>> migration of water and other fine trash from breaking the patch seal. > >> > > |
#10
|
|||
|
|||
I don't know where or how this became such a popular opinion that a repaired
tire is worthless. Probably the people who sell tires. $200 for a tire vs. $2 for a plug, maybe? I have run both patched and plugged tires at speeds most you who only dream of and have had no failures and no indication of impending failure by examining the repair after such use. I've even plugged and patched race slicks, which according to many is the supreme no-no. Supposedly, you can't plug a slick because the tread is not thick enough to hold. However, I have never had one indicate any separation or pulling out. They have actually performed better than patches as patches tend to make a large spot wear more than the surrounding tread. As such, when patching slicks, I never used a full size patch, but always cut the patch smaller to minimize the wear spot. The problem many claim is due to the steel belts being broken by the puncturing object, i.e., nail, screw, etc. The real problem is steel belts. They are heavy, thus they are more rotating mass and tend to expand more at high speed than a similar non-steel cord. This is why John Greenwood was able to race on B.F. Goodrich TAs in the early '70s even though they were not speed rated. This is also why Firestone 500 tires blew apart, especially on Corvettes. The steel belts worked fine at 55 mph but when taken to the 120 mph even a '75 low horse Corvette was capable of, the belts literally tore out of the carcass due to the design by Firestone. Fix a Flat on the other hand, is a problem. It rarely ever flows evenly around the outside of the tire, instead puddling and creating a heavy spot that throws the tire out of balance. It is a mess to clean out, and the fumes are explosive so that removal of the tire can be hazardous. "C5Guy" > wrote in message ... > Can you really trust a "repaired" tyre, especially at high speed..... > > "Dad" > wrote in message > ... > > "H and A" > wrote in message > > news > >> Found a nail in the tread portion on one of my Goodyear Run Flat tires. > >> Once removed, is this something that can be plugged, without harming the > >> tire pressure sensor? Any thing special I need to know about repairing > >> the tire before I remove the nail? > > Unless you plan on replacing it very soon plugging it is not the answer. > > To continue to use the tire you need to plug and then patch from the > > inside. The patch is to contain the air and the plug is to stop the > > migration of water and other fine trash from breaking the patch seal. You > > should not be able to damage the pressure sensor by plugging the tire, it > > is about the size of an old Zippo lighter and attached to the valve stem. > > The only warnings I've heard on them being damaged is the use of > > "Fix-A-Flat" or tire removal by an incompetent tire repair shop. Dally > > Tire a Goodyear dealer in Coldwater Mi. charged $10 to repair a tire, > > Capitol Tire in Toledo got me for $56 just to mount one, a Goodyear dealer > > that will never see me again. Plus I would like for them to get all of the > > attention that I paid for by passing this on to everyone. > > -- > > Dad > > 05 C6 Silver/Red 6spd Z51 > > 72 Shark Black/Black/4spd > > > > |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
BMW Recommended Tire Balance | mwh | BMW | 8 | November 9th 04 11:17 AM |
1999 323i Convertible - Winter Tire Question | C.R. Krieger | BMW | 2 | September 28th 04 06:55 PM |
Tire pressure must be monitored on new models !!! | news | BMW | 2 | September 20th 04 10:24 PM |
Proper tire pressure for Firestone Indy 500 FireHawk - 74 Vette | Tom in Missouri | Corvette | 2 | August 11th 04 04:21 PM |
Proper tire pressure for Firestone Indy 500 FireHawk - 74 Vette - Can anyone read? | Tom in Missouri | Corvette | 0 | August 10th 04 05:30 PM |