If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
OBD emission test question
I took my 1997 Mazda Protege in for its Illinois periodic emission
test last week. Happily, it passed, but I have a question about the test itself. Beginning now, Illinois is checking the OBD in all vehicles manufactured in 1996 and later INSTEAD of the exhaust test for hydrocarbons and CO2. That's fine with me, but I couldn't figure out how they do it. Let me explain. When the car is being tested, the driver is asked to step into a kind of waiting room from which he or she can see the car and the test display, but can't see what the attendant is actually doing. All I could see was the attendant perched on the end of the driver's seat. He had in his hand an electrical device of some kind attached to the end of a thick cable that ran up toward the ceiling and into the booth where all the testing meters are. The box didn't seem to be connected to anything in the car, yet apparently some sort of data was being collected and transmitted to a computer inside the booth. How does this thing work? I thought there'd have to be a direct electrical connection of some kind to a jack or other connector in the car, but as far as I could see, there wasn't. In fact, in the instructions on the emission test notice there's a sentence that says that if your OBD connector is covered, it's the owner's responsibility to remove the cover before testing. The owner's manual, however, is virtually silent about the OBD and any cover. Is there a transponder or transmitter of some kind in the car? Any comment or explanation will be gratefully received. -Len |
Ads |
#2
|
|||
|
|||
In article >,
LenS > wrote: > I took my 1997 Mazda Protege in for its Illinois periodic emission > test last week. Happily, it passed, but I have a question about the > test itself. > > Beginning now, Illinois is checking the OBD in all vehicles > manufactured in 1996 and later INSTEAD of the exhaust test for > hydrocarbons and CO2. > > That's fine with me, but I couldn't figure out how they do it. Let me > explain. > > When the car is being tested, the driver is asked to step into a kind > of waiting room from which he or she can see the car and the test > display, but can't see what the attendant is actually doing. > > All I could see was the attendant perched on the end of the driver's > seat. He had in his hand an electrical device of some kind attached to > the end of a thick cable that ran up toward the ceiling and into the > booth where all the testing meters are. > > The box didn't seem to be connected to anything in the car, yet > apparently some sort of data was being collected and transmitted to a > computer inside the booth. > > How does this thing work? I thought there'd have to be a direct > electrical connection of some kind to a jack or other connector in the > car, but as far as I could see, there wasn't. In fact, in the > instructions on the emission test notice there's a sentence that says > that if your OBD connector is covered, it's the owner's responsibility > to remove the cover before testing. The owner's manual, however, is > virtually silent about the OBD and any cover. > > Is there a transponder or transmitter of some kind in the car? > > Any comment or explanation will be gratefully received. They plugged into the OBD2 diagnostic port, you just couldn't see it from your vantage point. I doubt that Envirotest would refuse to test a vehicle that had a factory installed cover on the plug (some do, most don't), the blurb in their literature is in regards to a non-stock cover, something like stereo equipment or a trailer brake controller or something intentionally mounted to circumvent them plugging in and testing your vehicle (though some people -do- try). The test scans your vehicles powertrain control module for trouble codes and failed/un-run emissions monitors. There is no transponder or transmitter. The reason your owners manual doesn't go into great depth about the workings of the OBD2 test port is because it is not there as a user serviceable item. The lane attendant can not boof the test, that part has already been anticipated and dealt with, believe me, honestly, they really -did- plug into your vehicle. |
#3
|
|||
|
|||
The connector is under the dash beside the steering column...
|
#4
|
|||
|
|||
> The test scans your vehicles powertrain control module for > trouble codes and failed/un-run emissions monitors. There is no > transponder or transmitter. That's coming in OBD-III.. Regards, Jim |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Where to get Official Speed Limit Info | [email protected] | Driving | 40 | January 3rd 05 07:10 AM |
Compression test question | Kevin S | Jeep | 3 | December 22nd 04 11:46 PM |
Oxygen sensor / emission test | Jeff Rogers | Technology | 8 | December 15th 04 04:10 AM |
Fail Emission Test | ronnie802 | Saturn | 9 | July 22nd 04 12:57 AM |
Dumb question regarding compression test on Audi a4 1.8t | G | Audi | 5 | June 23rd 04 06:47 PM |