If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
tech questions: 93 wrangler, 93 gr cher
howdy y'all, two tech questions:
93 wrangler 4.0 ticking sound early in the morning, only has happened a couple times. i want to say cold weather ping, but it's been way colder with no ping. it sounds like ignition or valve train related? like every other revolution tick sound. it went away after a couple minutes driving, and then back to purring like a kitten. 93 grand cherokee 4.0 (buying for my wife) has a hard time starting after it's sat for a while, overnight not so bad, but a couple days and she cranks for a while. i want to say fuel pump check valve is draining back. sound about right? if this is it, i might build a timer circuit to bump the pressure before cranking. -- Ben Jerew AKA PolarPuppy ASE Certified Master Technician New Country Lexus of Latham, NY, USA Amateur Off-Roader 93 YJ 4.0l 3spd |
Ads |
#2
|
|||
|
|||
MudPuppy76 did pass the time by typing:
> howdy y'all, two tech questions: > > 93 wrangler 4.0 ticking sound early in the > morning, only has happened a couple times. i want > to say cold weather ping, but it's been way colder > with no ping. it sounds like ignition or valve > train related? like every other revolution tick > sound. it went away after a couple minutes > driving, and then back to purring like a kitten. Probably needs an oil change. The I6 isn't the worlds most quiet engine when it's older. It could be your getting a teeny crack in the exhaust pipe, that will sound like a tick till the metal heats up and seals it off. Eventually it will sound like a diesel and you will have to replace it. (they all crack) linky: http://members.cox.net/douglas.wilson/banks/ > 93 grand cherokee 4.0 (buying for my wife) has a > hard time starting after it's sat for a while, > overnight not so bad, but a couple days and she > cranks for a while. i want to say fuel pump check > valve is draining back. sound about right? if this > is it, i might build a timer circuit to bump the > pressure before cranking. Either fuel pump check valve or fuel rail pressure regulator has failed. Get a fuel pressure gauge and check the rail. 32 psi at idle, take the hose off the regulator and it should jump 3-4psi, turn the engine off and the pressure should stay level for more than an hour. To check which one is leaking you have to use a special hose that can be clamped. Clamping the OEM hoses isn't a good idea. At two days I wouldn't be worrying. Just tell here to turn the key on, then off, wait a sec, then on again, then start. You might need to replace the fuel filter. -- -- DougW -- 93 ZJ 4.0 http://members.cox.net/wilsond HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors Banks Header - and BEER, in the fridge! |
#3
|
|||
|
|||
MudPuppy76 <"<moc.rr.pacyn"@"pupralop"> proclaimed:
> howdy y'all, two tech questions: > > 93 wrangler 4.0 ticking sound early in the morning, only has happened a > couple times. i want to say cold weather ping, but it's been way colder > with no ping. it sounds like ignition or valve train related? like every > other revolution tick sound. it went away after a couple minutes > driving, and then back to purring like a kitten. > > 93 grand cherokee 4.0 (buying for my wife) has a hard time starting > after it's sat for a while, overnight not so bad, but a couple days and > she cranks for a while. i want to say fuel pump check valve is draining > back. sound about right? if this is it, i might build a timer circuit to > bump the pressure before cranking. > Quick diagnostic on the ZJ would be to turn the key on, wait a coupla seconds. If it starts right away then, the fuel system is losing pressure somewhere. On the 93 don't know if there is also a fuel rail check valve. |
#4
|
|||
|
|||
MudPuppy76 <"<moc.rr.pacyn"@"pupralop"> wrote: > 93 grand cherokee 4.0 (buying for my wife) has a > hard time starting after it's sat for a while, > overnight not so bad, but a couple days and she > cranks for a while. i want to say fuel pump check > valve is draining back. sound about right? if this > is it, i might build a timer circuit to bump the > pressure before cranking. Put a gauge on it and monitor bleeddown pressure overnight. If it is your pump checkball, then I would think you would want to replace the pump - esp. if it is a high mileage unit, rather than insert a homemade timer into the FP circuit. The pump should run Key On anyway. Its the operation of the injectors during cranking that bleed the fuel line of air when you have a fuel drainback problem, not fuel pressure alone. And incase this is just coincidence that the engine only has trouble on extended sits --- the 4.0 of that era had problems with its crank sensor. Not sure if it was still a problem part by 1993 though. Their output level would weaken at cranking speeds and cause either a no start or a long crank. Just something to think about, Toyota MDT in MO |
#5
|
|||
|
|||
Comboverfish wrote:
> MudPuppy76 <"<moc.rr.pacyn"@"pupralop"> wrote: > >>93 grand cherokee 4.0 (buying for my wife) has a >>hard time starting after it's sat for a while, >>overnight not so bad, but a couple days and she >>cranks for a while. i want to say fuel pump check >>valve is draining back. sound about right? if this >>is it, i might build a timer circuit to bump the >>pressure before cranking. > > > Put a gauge on it and monitor bleeddown pressure overnight. If it is > your pump checkball, then I would think you would want to replace the > pump - esp. if it is a high mileage unit, rather than insert a homemade > timer into the FP circuit. The pump should run Key On anyway. Its the > operation of the injectors during cranking that bleed the fuel line of > air when you have a fuel drainback problem, not fuel pressure alone. > > And incase this is just coincidence that the engine only has trouble on > extended sits --- the 4.0 of that era had problems with its crank > sensor. Not sure if it was still a problem part by 1993 though. Their > output level would weaken at cranking speeds and cause either a no > start or a long crank. Just something to think about, > > Toyota MDT in MO > will check the fuel pressure when i get back to the shop on monday. maybe put a scope on the crank sensor just to see. -- Ben Jerew AKA PolarPuppy ASE Certified Master Technician New Country Lexus of Latham, NY, USA Amateur Off-Roader 93 YJ 4.0l 3spd |
#6
|
|||
|
|||
If it is the fuel pump check valve, you would probably only have problems
starting when the engine is warm. (same symptoms as a bad fuel pressure regulator). If you put a pressure gauge on the fuel test port you should hold pressure after shutdown. If not it is either the fuel pressure regulator or the aformentioned check valve. If it is the valve, I agree with above post, you should replace the pump. I just did this on my '94, not a bad job, but the pump is expensive. I got one for 235 from autozone. HTH, Phil "MudPuppy76 <"<moc.rr.pacyn"@"pupralop">" <--SDRAWKCAB> wrote in message ... > Comboverfish wrote: > >> MudPuppy76 <"<moc.rr.pacyn"@"pupralop"> wrote: >> >>>93 grand cherokee 4.0 (buying for my wife) has a >>>hard time starting after it's sat for a while, >>>overnight not so bad, but a couple days and she >>>cranks for a while. i want to say fuel pump check >>>valve is draining back. sound about right? if this >>>is it, i might build a timer circuit to bump the >>>pressure before cranking. >> >> >> Put a gauge on it and monitor bleeddown pressure overnight. If it is >> your pump checkball, then I would think you would want to replace the >> pump - esp. if it is a high mileage unit, rather than insert a homemade >> timer into the FP circuit. The pump should run Key On anyway. Its the >> operation of the injectors during cranking that bleed the fuel line of >> air when you have a fuel drainback problem, not fuel pressure alone. >> >> And incase this is just coincidence that the engine only has trouble on >> extended sits --- the 4.0 of that era had problems with its crank >> sensor. Not sure if it was still a problem part by 1993 though. Their >> output level would weaken at cranking speeds and cause either a no >> start or a long crank. Just something to think about, >> >> Toyota MDT in MO >> > will check the fuel pressure when i get back to the shop on monday. maybe > put a scope on the crank sensor just to see. > > -- > Ben Jerew AKA PolarPuppy > ASE Certified Master Technician > New Country Lexus of Latham, NY, USA > Amateur Off-Roader 93 YJ 4.0l 3spd |
#7
|
|||
|
|||
yeah, i'm gonna have to go with the fuel pump.
sadly though, i have to get a fuel pump for my 93 yj too (leaking out the top if i fill it up too much) crap, i'm not made out of money, just carbon and water! Phil Rynn wrote: > If it is the fuel pump check valve, you would probably only have problems > starting when the engine is warm. (same symptoms as a bad fuel pressure > regulator). If you put a pressure gauge on the fuel test port you should > hold pressure after shutdown. If not it is either the fuel pressure > regulator or the aformentioned check valve. > If it is the valve, I agree with above post, you should replace the pump. > I just did this on my '94, not a bad job, but the pump is expensive. I got > one for 235 from autozone. >>Comboverfish wrote: >> >> >>>MudPuppy76 <"<moc.rr.pacyn"@"pupralop"> wrote: >>> >>> >>>>93 grand cherokee 4.0 (buying for my wife) has a >>>>hard time starting after it's sat for a while, >>>>overnight not so bad, but a couple days and she >>>>cranks for a while. i want to say fuel pump check >>>>valve is draining back. sound about right? if this >>>>is it, i might build a timer circuit to bump the >>>>pressure before cranking. >>> >>> >>>Put a gauge on it and monitor bleeddown pressure overnight. If it is >>>your pump checkball, then I would think you would want to replace the >>>pump - esp. if it is a high mileage unit, rather than insert a homemade >>>timer into the FP circuit. The pump should run Key On anyway. Its the >>>operation of the injectors during cranking that bleed the fuel line of >>>air when you have a fuel drainback problem, not fuel pressure alone. >>> >>>And incase this is just coincidence that the engine only has trouble on >>>extended sits --- the 4.0 of that era had problems with its crank >>>sensor. Not sure if it was still a problem part by 1993 though. Their >>>output level would weaken at cranking speeds and cause either a no >>>start or a long crank. Just something to think about, >>> >>>Toyota MDT in MO >>> >> >>will check the fuel pressure when i get back to the shop on monday. maybe >>put a scope on the crank sensor just to see. -- Ben Jerew AKA PolarPuppy ASE Certified Master Technician New Country Lexus of Latham, NY, USA Amateur Off-Roader 93 YJ 4.0l 3spd |
#8
|
|||
|
|||
On Tue, 15 Feb 2005 01:50:19 GMT, "MudPuppy76
<\"<moc.rr.pacyn\"@\"pupralop\">" <--SDRAWKCAB> wrote: >yeah, i'm gonna have to go with the fuel pump. >sadly though, i have to get a fuel pump for my 93 >yj too (leaking out the top if i fill it up too >much) crap, i'm not made out of money, just carbon >and water! Ditto. That is why you get the parts from somewhere and do the job yourself. >Phil Rynn wrote: > >> If it is the fuel pump check valve, you would probably only have problems >> starting when the engine is warm. (same symptoms as a bad fuel pressure >> regulator). If you put a pressure gauge on the fuel test port you should >> hold pressure after shutdown. If not it is either the fuel pressure >> regulator or the aformentioned check valve. >> If it is the valve, I agree with above post, you should replace the pump. >> I just did this on my '94, not a bad job, but the pump is expensive. I got >> one for 235 from autozone. not OEM? here is an article about autozone fuel pumps you might want to read first, I have it archived so don't have the message number: \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ \\\\\\\\\\\\\\\\\\\\\\\ Your fuel pump is more than likely on it's way out, and it would be wise to replace it now than to wait and be stranded (don't ask me how I know this). I remember reading somewhere that these fuel pumps would get contaminated with the left over solder from when the fuel tanks were put together and get louder and fail. The same thing happened to me, and mine went all of a sudden. How I missed that noise that night... Also, spend the extra money and get a >OEM< fuel pump. As a tech, I have replaced many pumps 2 and 3 times because the aftermarket ones failed after a couple of months. I too bought a Master fuel pump from Autozone, and after 2 months the noise was back, so I returned it and got a Ford one, and haven't had trouble since. Since this is a very aggravating job and the pumps seem to always go right AFTER you fill up, do yourself a favor and get a good one the first time. \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ \\\\\\\\\\\\\\\\\\\\\\ EDITED: >OEM< was originally "Ford" in original message. Now do you _still_ want to go through all that HELL of replacing a fuel pump with autozone part, only to have to do it again in 2 months? Lg >>>Comboverfish wrote: >>> >>> >>>>MudPuppy76 <"<moc.rr.pacyn"@"pupralop"> wrote: >>>> >>>> >>>>>93 grand cherokee 4.0 (buying for my wife) has a >>>>>hard time starting after it's sat for a while, >>>>>overnight not so bad, but a couple days and she >>>>>cranks for a while. i want to say fuel pump check >>>>>valve is draining back. sound about right? if this >>>>>is it, i might build a timer circuit to bump the >>>>>pressure before cranking. >>>> >>>> >>>>Put a gauge on it and monitor bleeddown pressure overnight. If it is >>>>your pump checkball, then I would think you would want to replace the >>>>pump - esp. if it is a high mileage unit, rather than insert a homemade >>>>timer into the FP circuit. The pump should run Key On anyway. Its the >>>>operation of the injectors during cranking that bleed the fuel line of >>>>air when you have a fuel drainback problem, not fuel pressure alone. >>>> >>>>And incase this is just coincidence that the engine only has trouble on >>>>extended sits --- the 4.0 of that era had problems with its crank >>>>sensor. Not sure if it was still a problem part by 1993 though. Their >>>>output level would weaken at cranking speeds and cause either a no >>>>start or a long crank. Just something to think about, >>>> >>>>Toyota MDT in MO >>>> >>> >>>will check the fuel pressure when i get back to the shop on monday. maybe >>>put a scope on the crank sensor just to see. |
#9
|
|||
|
|||
What a pile of crap that post is!
'Solder' from making the tank contaminating the fuel pumps. ROTFLMAO! I have never heard anything so foolish. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Lawrence Glickman wrote: > > On Tue, 15 Feb 2005 01:50:19 GMT, "MudPuppy76 > <\"<moc.rr.pacyn\"@\"pupralop\">" <--SDRAWKCAB> wrote: > > >yeah, i'm gonna have to go with the fuel pump. > >sadly though, i have to get a fuel pump for my 93 > >yj too (leaking out the top if i fill it up too > >much) crap, i'm not made out of money, just carbon > >and water! > > Ditto. That is why you get the parts from somewhere and do the job > yourself. > > >Phil Rynn wrote: > > > >> If it is the fuel pump check valve, you would probably only have problems > >> starting when the engine is warm. (same symptoms as a bad fuel pressure > >> regulator). If you put a pressure gauge on the fuel test port you should > >> hold pressure after shutdown. If not it is either the fuel pressure > >> regulator or the aformentioned check valve. > >> If it is the valve, I agree with above post, you should replace the pump. > >> I just did this on my '94, not a bad job, but the pump is expensive. I got > >> one for 235 from autozone. > > not OEM? here is an article about autozone fuel pumps you might want > to read first, I have it archived so don't have the message number: > \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ \\\\\\\\\\\\\\\\\\\\\\\ > Your fuel pump is more than likely on it's way out, and it would be > wise to replace it now than to wait and be stranded (don't ask me how > I know this). I remember reading somewhere that these fuel pumps would > get contaminated with the left over solder from when the fuel tanks > were put together and get louder and fail. The same thing happened to > me, and mine went all of a sudden. How I missed that noise that > night... > Also, spend the extra money and get a >OEM< fuel pump. As a tech, I > have replaced many pumps 2 and 3 times because the aftermarket ones > failed after a couple of months. I too bought a Master fuel pump from > Autozone, and after 2 months the noise was back, so I returned it and > got a Ford one, and haven't had trouble since. Since this is a very > aggravating job and the pumps seem to always go right AFTER you fill > up, do yourself a favor and get a good one the first time. > \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ \\\\\\\\\\\\\\\\\\\\\\ > EDITED: >OEM< was originally "Ford" in original message. > > Now do you _still_ want to go through all that HELL of replacing a > fuel pump with autozone part, only to have to do it again in 2 months? > > Lg > > >>>Comboverfish wrote: > >>> > >>> > >>>>MudPuppy76 <"<moc.rr.pacyn"@"pupralop"> wrote: > >>>> > >>>> > >>>>>93 grand cherokee 4.0 (buying for my wife) has a > >>>>>hard time starting after it's sat for a while, > >>>>>overnight not so bad, but a couple days and she > >>>>>cranks for a while. i want to say fuel pump check > >>>>>valve is draining back. sound about right? if this > >>>>>is it, i might build a timer circuit to bump the > >>>>>pressure before cranking. > >>>> > >>>> > >>>>Put a gauge on it and monitor bleeddown pressure overnight. If it is > >>>>your pump checkball, then I would think you would want to replace the > >>>>pump - esp. if it is a high mileage unit, rather than insert a homemade > >>>>timer into the FP circuit. The pump should run Key On anyway. Its the > >>>>operation of the injectors during cranking that bleed the fuel line of > >>>>air when you have a fuel drainback problem, not fuel pressure alone. > >>>> > >>>>And incase this is just coincidence that the engine only has trouble on > >>>>extended sits --- the 4.0 of that era had problems with its crank > >>>>sensor. Not sure if it was still a problem part by 1993 though. Their > >>>>output level would weaken at cranking speeds and cause either a no > >>>>start or a long crank. Just something to think about, > >>>> > >>>>Toyota MDT in MO > >>>> > >>> > >>>will check the fuel pressure when i get back to the shop on monday. maybe > >>>put a scope on the crank sensor just to see. |
#10
|
|||
|
|||
In article >,
Mike Romain > wrote: > What a pile of crap that post is! > > 'Solder' from making the tank contaminating the fuel pumps. ROTFLMAO! > > I have never heard anything so foolish. The only thing close would be that Methanol will dissolve the Tern coating inside a steel tank, contaminating the entire fuel system. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Questions, questions, questions | Vernon Balbert | BMW | 15 | January 16th 05 03:01 AM |
1990 Ford F150 questions | papadad | Technology | 1 | January 7th 05 06:43 AM |
Where to get Official Speed Limit Info | [email protected] | Driving | 40 | January 3rd 05 07:10 AM |
Wrangler TJ Tire axle gearing Questions | Derek Proctor | 4x4 | 6 | June 3rd 04 02:28 PM |