If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
painting truck ?'s please read (long)
Hi group -
I have an '82 F-100 longbed that has a few rusty spots. I want to just get that "rat-rod" look of black primer, so I was thinking: buy 2 (?) gallons of flat black primer sand the rust spots (quarter sized), spray with aerosol MetalPrep, wash it and rinse it really well, take it to Maaco, and ask them to spray on the primer for $200 or so... I can't work on cars in my apt. complex, and spray cans look VERY crappy. I just want a CHEAP flat finish to carry my motorcycle around in. The truck is off-white now, and I know Maaco would not satisfy me with the results of a new paint job. Lots of trucks have this flat primer finish here in west Georgia, but now I'm afraid just primer alone is too porous, and the rust will start coming up through the paint. Is epoxy primer better? I want it to last a few years, and I'm 53, too worn out and busy to sand a vehicle down properly. I used pbblaster on the bumper bolts, just to help in removal. Now I hear that I should use flat black paint and "reduced" clearcoat to get the look I want, and that this will seal the body from further rust... so do I need 2 gallons? Exactly what kind of primer or black paint (think cheap) is best? I don't even know what flattener or reducers are, except that they get mixed with the paint... oh yes - 1 more question - getting a new windshield put in. My limited intelligence says to do this first, and then it can be masked off... try to think of the finish on the trucks INSIDE Old Navy stores....but black - not blue...has anyone seen these? and if you live near Atlanta and want to tackle this job, please email me.... thanks for input/ideas............:+) paul |
Ads |
#2
|
|||
|
|||
I'm kinda confused...you want to take it to Maaco to give it a cheap
paint job it but you don't think Maaco will do a good job? As long as your expectations for quality are in line with the price you are paying and you are willing to do some prep work I don't think you will be disappointed. Maaco has cranked out inexpensive paint jobs for years. Expect everything that isn't covered to be painted and that the paint job probably won't last as long as one that costs more. |
#3
|
|||
|
|||
That flat black look is NOT primer. It is regular paint treated with a
flatting agent to make it a flat color. NO PRIMER will last without a top coat. If your not really concerned about the final look take it in and have the entire truck shot with bed liner. -- Steve Williams Near Cooperstown, New York > wrote in message oups.com... > Hi group - > I have an '82 F-100 longbed that has a few rusty spots. I want to just > get that "rat-rod" look of black primer, so I was thinking: > buy 2 (?) gallons of flat black primer > sand the rust spots (quarter sized), spray with aerosol MetalPrep, wash > it and rinse it really well, take it to Maaco, and ask them to spray on > the primer for $200 or so... > I can't work on cars in my apt. complex, and spray cans look VERY > crappy. I just want a CHEAP flat finish to carry my motorcycle around > in. > The truck is off-white now, and I know Maaco would not satisfy me with > the results of a new paint job. > Lots of trucks have this flat primer finish here in west Georgia, but > now I'm afraid just primer alone is too porous, and the rust will start > coming up through the paint. Is epoxy primer better? > I want it to last a few years, and I'm 53, too worn out and busy to > sand a vehicle down properly. > I used pbblaster on the bumper bolts, just to help in removal. > Now I hear that I should use flat black paint and "reduced" clearcoat > to get the look I want, and that this will seal the body from further > rust... > so do I need 2 gallons? Exactly what kind of primer or black paint > (think cheap) is best? I don't even know what flattener or reducers > are, except that they get mixed with the paint... > oh yes - 1 more question - getting a new windshield put in. My limited > intelligence says to do this first, and then it can be masked off... > try to think of the finish on the trucks INSIDE Old Navy stores....but > black - not blue...has anyone seen these? > and if you live near Atlanta and want to tackle this job, please email > me.... > thanks for input/ideas............:+) paul > ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==---- http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups ----= East and West-Coast Server Farms - Total Privacy via Encryption =---- |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Please Read: OWN A CAR? - YOUR MISSING OUT! | Edward Tyshkevich | Alfa Romeo | 1 | October 25th 04 07:58 PM |
Please Read: Buy a Car $50 Dollars over Dealer Cost!!!!!!!!!!! | Edward Tyshkevich | 4x4 | 0 | October 16th 04 06:11 AM |
PLEASE READ: Car Secrets Revealed! | Edward Tyshkevich | General | 1 | October 15th 04 06:23 AM |
Holley Truck Avenger | Ltine | 4x4 | 0 | August 22nd 04 08:32 PM |
Need help with paint (long but PLEASE read) | JK | Antique cars | 0 | October 13th 03 10:32 AM |