If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
XJ name that part/pieces
Crap. Past couple of days I notice my fuel economy going to hell, got home
from work today and was about to leave again when the xj wouldn't crank. Opened up the hood and the first injector was spewing gas everywhere, so I replaced all fuel injector o-rings. When I was putting it all back together (losing daylight so I was hurrying) I got it all back and went to plug in what I believe is the Fuel Return Line, and I cut the o-rings by putting it back in hastily. There were 2 orange rings on the outside of a black ring. Its on a 90 XJ 4.0L. Is this the fuel return line? Coming off the fuel rail, front of the engine, to a metal fuel line? I need to know specifically what to ask for, I dont trust the parts guys too much. I'm so ****ed I cut those o-rings!!! argh! Troy |
Ads |
#2
|
|||
|
|||
XJ name that part/pieces
When all else fails, take a digital pic of it, and SHOW it to them.
Kate "Troy" <@ .> wrote in message . .. > Crap. Past couple of days I notice my fuel economy going to hell, got > home from work today and was about to leave again when the xj wouldn't > crank. Opened up the hood and the first injector was spewing gas > everywhere, so I replaced all fuel injector o-rings. > > When I was putting it all back together (losing daylight so I was > hurrying) I got it all back and went to plug in what I believe is the Fuel > Return Line, and I cut the o-rings by putting it back in hastily. There > were 2 orange rings on the outside of a black ring. > > Its on a 90 XJ 4.0L. Is this the fuel return line? Coming off the fuel > rail, front of the engine, to a metal fuel line? I need to know > specifically what to ask for, I dont trust the parts guys too much. I'm so > ****ed I cut those o-rings!!! argh! > > Troy > |
#3
|
|||
|
|||
XJ name that part/pieces
Ya I stopped by autozone today and they didn't know anything about it and
their computers didn't help. I ended up buying a multi o-ring pack and making it work with some redneck ingenuity. Although now it's all back together the damn injector is still leaking, the rail seems to cut the o-ring. I just came inside to get some water while I sent the gf to get another pack of them. I'll let ya'll know how this turns out and what that damn piece is called when I find out. Troy "Kate" > wrote in message .. . > When all else fails, take a digital pic of it, and SHOW it to them. > > Kate > > "Troy" <@ .> wrote in message > . .. >> Crap. Past couple of days I notice my fuel economy going to hell, got >> home from work today and was about to leave again when the xj wouldn't >> crank. Opened up the hood and the first injector was spewing gas >> everywhere, so I replaced all fuel injector o-rings. >> >> When I was putting it all back together (losing daylight so I was >> hurrying) I got it all back and went to plug in what I believe is the >> Fuel Return Line, and I cut the o-rings by putting it back in hastily. >> There were 2 orange rings on the outside of a black ring. >> >> Its on a 90 XJ 4.0L. Is this the fuel return line? Coming off the fuel >> rail, front of the engine, to a metal fuel line? I need to know >> specifically what to ask for, I dont trust the parts guys too much. I'm >> so ****ed I cut those o-rings!!! argh! >> >> Troy >> > > |
#4
|
|||
|
|||
XJ name that part/pieces
Troy wrote:
> Its on a 90 XJ 4.0L. Is this the fuel return line? Coming off the > fuel rail, front of the engine, to a metal fuel line? I need to know > specifically what to ask for, I dont trust the parts guys too much. > I'm so ****ed I cut those o-rings!!! argh! On the rail from the front. Fuel return () pressure regulator Fuel supply injector 1 ... injector 6 http://revbeergoggles.com/Fixes/fuel...-regulator.jpg I'm not sure if you have the same type of connector I do but mine has a couple of ears, two o-rings and a plastic seperator. That's an assembly and a real bitch to replace. better pic. Ignore the bit ass pressure regulator. http://www.revbeergoggles.com/temp/fuel-rail-1.jpg If that's the connector then the part you need is. 1-83502745 or at least the rings from it. http://www.revbeergoggles.com/temp/core.jpg How exactly that goes in I dunno. Your supposed to pry out the old rings and plasitc spacer then shove this in, twist the plug out and your done. Me, I had a spare connector assembly from another project. -- -- DougW -- 93 ZJ 4.0 http://revbeergoggles.com HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors Banks Header - and BEER, in the fridge! |
#5
|
|||
|
|||
XJ name that part/pieces
I hope you didn't tear yours down to show me! If you did you have one clean
ride. Yup thats the little part I will be needing. I kinda forced it back in with some aftermarket o-rings and the plastic piece spread a little and it doesn't leak for now, so I will keep that part number in case it does spring a leak. The o-ring that was being cut when I was pushing the fuel rail back on the injector, this time I lube'd it with some wd-40 and it went on with no problems. I now have no leaks thankfully, but I'm sure the next thing that may have a problem would be that connector you identified for me, thanks a bunch! I would not have been able to find it on my own for sure, was it in the FSM? Troy "DougW" > wrote in message news:W8OCg.251$JR5.149@dukeread11... > Troy wrote: > >> Its on a 90 XJ 4.0L. Is this the fuel return line? Coming off the >> fuel rail, front of the engine, to a metal fuel line? I need to know >> specifically what to ask for, I dont trust the parts guys too much. >> I'm so ****ed I cut those o-rings!!! argh! > > On the rail from the front. > > Fuel return () pressure regulator > Fuel supply > > injector 1 > ... > injector 6 > > http://revbeergoggles.com/Fixes/fuel...-regulator.jpg > > I'm not sure if you have the same type of connector I do but > mine has a couple of ears, two o-rings and a plastic seperator. > That's an assembly and a real bitch to replace. > > better pic. Ignore the bit ass pressure regulator. > http://www.revbeergoggles.com/temp/fuel-rail-1.jpg > > If that's the connector then the part you need is. > 1-83502745 or at least the rings from it. > http://www.revbeergoggles.com/temp/core.jpg > > How exactly that goes in I dunno. Your supposed to pry out the > old rings and plasitc spacer then shove this in, twist the plug > out and your done. Me, I had a spare connector assembly from > another project. > > > -- > -- DougW -- 93 ZJ 4.0 http://revbeergoggles.com > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors > Banks Header - and BEER, in the fridge! > |
#6
|
|||
|
|||
XJ name that part/pieces
Troy wrote:
> I hope you didn't tear yours down to show me! If you did you have > one clean ride. Nah, I didn't tear it apart. But I do take pictures when it is. > The o-ring that was being cut when I was pushing the fuel rail back > on the injector, this time I lube'd it with some wd-40 and it went on > with no problems. I now have no leaks thankfully, but I'm sure the > next thing that may have a problem would be that connector you > identified for me, thanks a bunch! I would not have been able to > find it on my own for sure, was it in the FSM? When doing injectors or any o-ring work (including the fuel filter which has the same type of connector) it's important to squirt a bit of motor oil on the rings. That repair part is shown in the FSM but it's not even in the online catalog used at the dealer. It's a specialty repair part that was intended to be used every time any fuel rail was off and not just for the Jeep. Thing is they never use them so it dropped off the normal ordering system. They still have them though. It's just a carrier for the o-rings and spacer. I wish they would have used AN fittings. Heck, next mod will probably be custom fuel line. Especially if we go to E85 around here. The stock rubber lines/pump/rings will melt with that much ethanol. What ever you do, don't loose those injector clips. They only come with a new rail and that sucker is way expensive. They are also a hard to find junkyard part. -- -- DougW -- 93 ZJ 4.0 http://revbeergoggles.com HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors Banks Header - and BEER, in the fridge! |
#7
|
|||
|
|||
XJ name that part/pieces
Doug, if you lose a clip just buy a large safety pin that has the same
approximate size wire and bend yourself a new one. It will last at least as long as the "official" ones do. On Fri, 11 Aug 2006 00:47:12 UTC "DougW" > wrote: > Troy wrote: > > I hope you didn't tear yours down to show me! If you did you have > > one clean ride. > > Nah, I didn't tear it apart. But I do take pictures when it is. > > > The o-ring that was being cut when I was pushing the fuel rail back > > on the injector, this time I lube'd it with some wd-40 and it went on > > with no problems. I now have no leaks thankfully, but I'm sure the > > next thing that may have a problem would be that connector you > > identified for me, thanks a bunch! I would not have been able to > > find it on my own for sure, was it in the FSM? > > When doing injectors or any o-ring work (including the fuel filter > which has the same type of connector) it's important to squirt a bit > of motor oil on the rings. > > That repair part is shown in the FSM but it's not even in the online > catalog used at the dealer. It's a specialty repair part that was > intended to be used every time any fuel rail was off and not just for > the Jeep. Thing is they never use them so it dropped off the normal > ordering system. They still have them though. It's just a carrier > for the o-rings and spacer. > > I wish they would have used AN fittings. Heck, next mod will probably > be custom fuel line. Especially if we go to E85 around here. The > stock rubber lines/pump/rings will melt with that much ethanol. > > What ever you do, don't loose those injector clips. They only come > with a new rail and that sucker is way expensive. They are also a > hard to find junkyard part. > -- Will Honea |
#8
|
|||
|
|||
XJ name that part/pieces
Did you think to lube the o-ring before squeezing it back in? I've
used engine oil, 3-1, silicone, and soap - all seem to work a lot better than a dry fit. K-Y might work as well... On Thu, 10 Aug 2006 20:46:17 UTC "Troy" <@á.> wrote: > Ya I stopped by autozone today and they didn't know anything about it and > their computers didn't help. I ended up buying a multi o-ring pack and > making it work with some redneck ingenuity. Although now it's all back > together the damn injector is still leaking, the rail seems to cut the > o-ring. I just came inside to get some water while I sent the gf to get > another pack of them. I'll let ya'll know how this turns out and what that > damn piece is called when I find out. > > Troy > > "Kate" > wrote in message > .. . > > When all else fails, take a digital pic of it, and SHOW it to them. > > > > Kate > > > > "Troy" <@ .> wrote in message > > . .. > >> Crap. Past couple of days I notice my fuel economy going to hell, got > >> home from work today and was about to leave again when the xj wouldn't > >> crank. Opened up the hood and the first injector was spewing gas > >> everywhere, so I replaced all fuel injector o-rings. > >> > >> When I was putting it all back together (losing daylight so I was > >> hurrying) I got it all back and went to plug in what I believe is the > >> Fuel Return Line, and I cut the o-rings by putting it back in hastily. > >> There were 2 orange rings on the outside of a black ring. > >> > >> Its on a 90 XJ 4.0L. Is this the fuel return line? Coming off the fuel > >> rail, front of the engine, to a metal fuel line? I need to know > >> specifically what to ask for, I dont trust the parts guys too much. I'm > >> so ****ed I cut those o-rings!!! argh! > >> > >> Troy > >> > > > > > > -- Will Honea |
Thread Tools | |
Display Modes | |
|
|