If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
1984 Laser: Manual Transmission Shifting Problems Cold
I have a 1984 Chrysler Laser with manual transmission.
I have shifting problems when it is cold (significantly below freezing) but not normally. The shift lever will go forward and back but not left to right (in the location it normally moves left and right). Do I have ice somewhere???? Where? What is the explanation? Solution? Thank you. -- Jonathan Grobe Books Browse our inventory of thousands of used books at: http://www.grobebooks.com |
Ads |
#2
|
|||
|
|||
On Mon, 20 Dec 2004 02:44:08 +0000 (UTC), Jonathan Grobe
> wrote: >I have a 1984 Chrysler Laser with manual transmission. >I have shifting problems when it is cold (significantly below >freezing) but not normally. > >The shift lever will go forward and back but not left >to right (in the location it normally moves left and >right). > >Do I have ice somewhere???? Where? What is the >explanation? Solution? The explanation is the viscosity of your transmission oil becomes that of cold molasses at these temperatures, and you can get it into gear when cold if you are patient. Once warmed up, it will work as normal. If you don't want this problem, put some kind of heater under your transmission. See your dealer or auto parts store. Lg > >Thank you. |
#3
|
|||
|
|||
On Mon, 20 Dec 2004 02:44:08 +0000 (UTC), Jonathan Grobe
> wrote: >I have a 1984 Chrysler Laser with manual transmission. >I have shifting problems when it is cold (significantly below >freezing) but not normally. > >The shift lever will go forward and back but not left >to right (in the location it normally moves left and >right). > >Do I have ice somewhere???? Where? What is the >explanation? Solution? The explanation is the viscosity of your transmission oil becomes that of cold molasses at these temperatures, and you can get it into gear when cold if you are patient. Once warmed up, it will work as normal. If you don't want this problem, put some kind of heater under your transmission. See your dealer or auto parts store. Lg > >Thank you. |
#4
|
|||
|
|||
Lawrence Glickman wrote:
> The explanation is the viscosity of your transmission oil becomes that > of cold molasses at these temperatures, and you can get it into gear > when cold if you are patient. Once warmed up, it will work as normal. Did you actually read his post, Lawrence? Ian |
#5
|
|||
|
|||
Lawrence Glickman wrote:
> The explanation is the viscosity of your transmission oil becomes that > of cold molasses at these temperatures, and you can get it into gear > when cold if you are patient. Once warmed up, it will work as normal. Did you actually read his post, Lawrence? Ian |
#6
|
|||
|
|||
shiden_kai wrote:
> Lawrence Glickman wrote: > > >>The explanation is the viscosity of your transmission oil becomes that >>of cold molasses at these temperatures, and you can get it into gear >>when cold if you are patient. Once warmed up, it will work as normal. > > > Did you actually read his post, Lawrence? > > Ian Careful Ian! He'll threaten you then he'll Plonk you!!!! 8^) Bill Putney (To reply by e-mail, replace the last letter of the alphabet in my adddress with the letter 'x') |
#7
|
|||
|
|||
shiden_kai wrote:
> Lawrence Glickman wrote: > > >>The explanation is the viscosity of your transmission oil becomes that >>of cold molasses at these temperatures, and you can get it into gear >>when cold if you are patient. Once warmed up, it will work as normal. > > > Did you actually read his post, Lawrence? > > Ian Careful Ian! He'll threaten you then he'll Plonk you!!!! 8^) Bill Putney (To reply by e-mail, replace the last letter of the alphabet in my adddress with the letter 'x') |
#8
|
|||
|
|||
"Jonathan Grobe" > wrote in message ... >I have a 1984 Chrysler Laser with manual transmission. > I have shifting problems when it is cold (significantly below > freezing) but not normally. > > The shift lever will go forward and back but not left > to right (in the location it normally moves left and > right). I would look for a build-up of grease on the transmission shift levers, which will trap dirt which in turn will absorb water which will freeze. Clean everything and lubricate with light oil. You can see these under the hood. I had one of those beasts for a while in the early 1990s, and if I recall correctly the end of the cables had rubber boots over them, which could easily trap dirt. |
#9
|
|||
|
|||
"Jonathan Grobe" > wrote in message ... >I have a 1984 Chrysler Laser with manual transmission. > I have shifting problems when it is cold (significantly below > freezing) but not normally. > > The shift lever will go forward and back but not left > to right (in the location it normally moves left and > right). I would look for a build-up of grease on the transmission shift levers, which will trap dirt which in turn will absorb water which will freeze. Clean everything and lubricate with light oil. You can see these under the hood. I had one of those beasts for a while in the early 1990s, and if I recall correctly the end of the cables had rubber boots over them, which could easily trap dirt. |
#10
|
|||
|
|||
Jonathan Grobe wrote: > I have a 1984 Chrysler Laser with manual transmission.>>>> The advice you received regarding shift cable binding is worth checking out. (Especially the cable that selects the different shift forks left to right) An extra thought: I have overhauled 5 or 10 of the K car transaxles (I think New Process 535s) and during the late 80's it seems like Chrysler retroactively began specifying ATF for trans lube verses 90 weight. I have always used ATF with no problem. It gets down near 0 degrees F. here for a couple weeks a year, but shifting my and my customer's Chryslers was no problem due to the thinner oil. No durability problems to note either. I got a customer in once with a 89 Omni that had a wasted mainshaft and diff bearings. It had recently been to a 'Trans' shop who used 90 weight during an overhaul. The fix was to do it all over again with new parts and ofcourse use ATF. Toyota MDT in MO |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
ATF in manual transmission?! | Jeff Strickland | BMW | 9 | December 25th 04 07:45 PM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 10 | December 18th 04 05:15 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 10 | October 16th 04 05:28 AM |
E39 (530d) Problems with automatic transmission? | Marko Grossmann | BMW | 12 | October 16th 04 04:47 AM |