If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Does the Chrysler Corporation Car Production Broadcast paper show pinion bearing preload and pinion nut torque?
The pinion nut of my 1976 Dodge Royal Monaco loosened. Does the Chrysler Corporation Car Production Broadcast paper that I found under the car seat show pinion bearing preload and pinion nut torque? On the paper there is PIN valued at 26 and P/Shaft valued at 251. Are these the factory settings of the pinion bearing preload and pinion nut torque? If not, is there a way to determine these through the papers. Does anyone know the pinion bearing preload and pinion nut torque that the factory used for a 1976 Dodge Royal Monaco? Thank you for a reply to this newsgroup, J. Pallendino Cleveland, Ohio USA |
Ads |
#2
|
|||
|
|||
The factory service manual should give you a torque value. The later
manuals give a rotating torque for the shaft of a few inch oz. You are crushing a collar inside on the shaft to set the preload so don't over do it because you cannot back it off it you set it too much. It takes a lot of FT Lbs on the nut to crush the collar. When you get close do 1/16 of a turn increments. It most likely will require a cheater bar handle extender to get enough torque to turn the nut. On Sat, 18 Sep 2004 21:42:38 GMT, "JP" > wrote: > >The pinion nut of my 1976 Dodge Royal Monaco loosened. Does the Chrysler >Corporation Car Production Broadcast paper that I found under the car seat >show pinion >bearing preload and pinion nut torque? On the paper there is PIN valued >at 26 and P/Shaft valued at 251. Are these the factory settings of the >pinion bearing preload and >pinion nut torque? If not, is there a way to >determine these through the papers. > >Does anyone know the pinion bearing preload and >pinion nut torque that the factory used for a 1976 Dodge Royal >Monaco? > >Thank you for a reply to this newsgroup, > >J. Pallendino >Cleveland, Ohio USA > > > |
#3
|
|||
|
|||
The factory service manual should give you a torque value. The later
manuals give a rotating torque for the shaft of a few inch oz. You are crushing a collar inside on the shaft to set the preload so don't over do it because you cannot back it off it you set it too much. It takes a lot of FT Lbs on the nut to crush the collar. When you get close do 1/16 of a turn increments. It most likely will require a cheater bar handle extender to get enough torque to turn the nut. On Sat, 18 Sep 2004 21:42:38 GMT, "JP" > wrote: > >The pinion nut of my 1976 Dodge Royal Monaco loosened. Does the Chrysler >Corporation Car Production Broadcast paper that I found under the car seat >show pinion >bearing preload and pinion nut torque? On the paper there is PIN valued >at 26 and P/Shaft valued at 251. Are these the factory settings of the >pinion bearing preload and >pinion nut torque? If not, is there a way to >determine these through the papers. > >Does anyone know the pinion bearing preload and >pinion nut torque that the factory used for a 1976 Dodge Royal >Monaco? > >Thank you for a reply to this newsgroup, > >J. Pallendino >Cleveland, Ohio USA > > > |
#4
|
|||
|
|||
rotating spec is 24 inch lbs
John_F wrote: > The factory service manual should give you a torque value. The later > manuals give a rotating torque for the shaft of a few inch oz. You > are crushing a collar inside on the shaft to set the preload so don't > over do it because you cannot back it off it you set it too much. It > takes a lot of FT Lbs on the nut to crush the collar. When you get > close do 1/16 of a turn increments. It most likely will require a > cheater bar handle extender to get enough torque to turn the nut. > > On Sat, 18 Sep 2004 21:42:38 GMT, "JP" > wrote: > > > > >The pinion nut of my 1976 Dodge Royal Monaco loosened. Does the Chrysler > >Corporation Car Production Broadcast paper that I found under the car seat > >show pinion > >bearing preload and pinion nut torque? On the paper there is PIN valued > >at 26 and P/Shaft valued at 251. Are these the factory settings of the > >pinion bearing preload and > >pinion nut torque? If not, is there a way to > >determine these through the papers. > > > >Does anyone know the pinion bearing preload and > >pinion nut torque that the factory used for a 1976 Dodge Royal > >Monaco? > > > >Thank you for a reply to this newsgroup, > > > >J. Pallendino > >Cleveland, Ohio USA > > > > > > |
#5
|
|||
|
|||
rotating spec is 24 inch lbs
John_F wrote: > The factory service manual should give you a torque value. The later > manuals give a rotating torque for the shaft of a few inch oz. You > are crushing a collar inside on the shaft to set the preload so don't > over do it because you cannot back it off it you set it too much. It > takes a lot of FT Lbs on the nut to crush the collar. When you get > close do 1/16 of a turn increments. It most likely will require a > cheater bar handle extender to get enough torque to turn the nut. > > On Sat, 18 Sep 2004 21:42:38 GMT, "JP" > wrote: > > > > >The pinion nut of my 1976 Dodge Royal Monaco loosened. Does the Chrysler > >Corporation Car Production Broadcast paper that I found under the car seat > >show pinion > >bearing preload and pinion nut torque? On the paper there is PIN valued > >at 26 and P/Shaft valued at 251. Are these the factory settings of the > >pinion bearing preload and > >pinion nut torque? If not, is there a way to > >determine these through the papers. > > > >Does anyone know the pinion bearing preload and > >pinion nut torque that the factory used for a 1976 Dodge Royal > >Monaco? > > > >Thank you for a reply to this newsgroup, > > > >J. Pallendino > >Cleveland, Ohio USA > > > > > > |
#6
|
|||
|
|||
On Sat, 18 Sep 2004, JP wrote:
> > The pinion nut of my 1976 Dodge Royal Monaco loosened. Does the > Chrysler Corporation Car Production Broadcast paper that I found under > the car seat show pinion bearing preload and pinion nut torque? No, the broadcast sheet shows the equipment and trim the car was built with. Get your torque values out of the Factory Service Manual. |
#7
|
|||
|
|||
On Sat, 18 Sep 2004, JP wrote:
> > The pinion nut of my 1976 Dodge Royal Monaco loosened. Does the > Chrysler Corporation Car Production Broadcast paper that I found under > the car seat show pinion bearing preload and pinion nut torque? No, the broadcast sheet shows the equipment and trim the car was built with. Get your torque values out of the Factory Service Manual. |
Thread Tools | |
Display Modes | |
|
|