If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Creating a thread on a metal post?
So this is random, but Im scratching my head... trying to find a way to
mount a little mustang badge on my grille, the badge has little metal posts that arent quite long enough to reach.. Is there something that will put a thread on them so I can put on a nut and a bracket? I.E. the oposite of drilling and tapping a hole, can i thread a blank post somehow? If not, what can I use to bond chromed metal (permanently enough that some kid wont yank it off) |
Ads |
#2
|
|||
|
|||
On Thu, 2 Jun 2005 20:46:22 -0400, <japhar> wrote:
>So this is random, but Im scratching my head... trying to find a way to >mount a little mustang badge on my grille, the badge has little metal posts >that arent quite long enough to reach.. > >Is there something that will put a thread on them so I can put on a nut and >a bracket? I.E. the oposite of drilling and tapping a hole, can i thread a >blank post somehow? > >If not, what can I use to bond chromed metal (permanently enough that some >kid wont yank it off) > You need a die...as in "tap and die set" However, since those emblems are fairly soft metal, and the post diameter small, a die might not work. I've see some emblems held on with a stamped-steel, self-tapping nut similar to those pictured on this site: http://www.boltproducts.com/tinnerma...peed-nuts.html (look a the 'Palnut' models) DP Pics of the cars: http://tinyurl.com/d2q9u |
#3
|
|||
|
|||
On Thu, 2 Jun 2005 20:46:22 -0400, <japhar> wrote:
>So this is random, but Im scratching my head... trying to find a way to >mount a little mustang badge on my grille, the badge has little metal posts >that arent quite long enough to reach.. > stop scratching we have enough dandruff ya sand nig its dirty under that turbin >Is there something that will put a thread on them so I can put on a nut and >a bracket? I.E. the oposite of drilling and tapping a hole, can i thread a >blank post somehow? > i bet you shoot blanks ya tard >If not, what can I use to bond chromed metal (permanently enough that some >kid wont yank it off) > have them removable the kids will get your paint unless they get them off ya foctard h u r c a s t |
#4
|
|||
|
|||
What kind of grille do you have?
I have a billet gille on mine. I put a Cobra emblem in the middle of it. I used Automotive two sided tape, just like they use to attach the side emblems, it has held for several years, no problem. You clean the back really well with alcohol, let it dry. Over apply it, cut the excess off with a razor blade so that it it trimmed nicely around the edges of the emblem and stick it on. BUT my grille IS metal. The posts are very soft, if you try to thread one, you may have it break off. You MIGHT be able to use something like JB weld (or some sort of really good glue) screws to the back of the emblem or something like that if the back of the emblem is hollow <japhar> wrote in message ... | So this is random, but Im scratching my head... trying to find a way to | mount a little mustang badge on my grille, the badge has little metal posts | that arent quite long enough to reach.. | | Is there something that will put a thread on them so I can put on a nut and | a bracket? I.E. the oposite of drilling and tapping a hole, can i thread a | blank post somehow? | | If not, what can I use to bond chromed metal (permanently enough that some | kid wont yank it off) | | |
#5
|
|||
|
|||
japhar wrote:
> So this is random, but Im scratching my head... trying to find a way to > mount a little mustang badge on my grille, the badge has little metal posts > that arent quite long enough to reach.. > > Is there something that will put a thread on them so I can put on a nut and > a bracket? I.E. the oposite of drilling and tapping a hole, can i thread a > blank post somehow? > > If not, what can I use to bond chromed metal (permanently enough that some > kid wont yank it off) > > Get a piece of tubing that fit's over the posts, and extends past the post ends about 1/4". Get a screw (like #10), that is the same diameter as the post, and cut the head off. The screw should fit in the tube, and the tube should fit over the end of the post. Use JB Weld to hold it all together. I would even dril a couple of transverse holes in the tube to allow the JB Weld to spooge out and make a stronger bond and prevent air pockets. -- ..boB 1997 HD FXDWG - Turbocharged! 2001 Dodge Dakota QC 5.9/4x4/3.92 1966 Mustang Coupe - Daily Driver 1966 FFR Cobra - Ongoing project |
#6
|
|||
|
|||
Ohhh Bobby!
You much smart boy!!! ".boB" > wrote in message . com... | japhar wrote: | > So this is random, but Im scratching my head... trying to find a way to | > mount a little mustang badge on my grille, the badge has little metal posts | > that arent quite long enough to reach.. | > | > Is there something that will put a thread on them so I can put on a nut and | > a bracket? I.E. the oposite of drilling and tapping a hole, can i thread a | > blank post somehow? | > | > If not, what can I use to bond chromed metal (permanently enough that some | > kid wont yank it off) | > | > | | Get a piece of tubing that fit's over the posts, and extends past the post ends | about 1/4". Get a screw (like #10), that is the same diameter as the post, and cut | the head off. The screw should fit in the tube, and the tube should fit over the end | of the post. Use JB Weld to hold it all together. I would even dril a couple of | transverse holes in the tube to allow the JB Weld to spooge out and make a stronger | bond and prevent air pockets. | | -- | .boB | 1997 HD FXDWG - Turbocharged! | 2001 Dodge Dakota QC 5.9/4x4/3.92 | 1966 Mustang Coupe - Daily Driver | 1966 FFR Cobra - Ongoing project | |
#7
|
|||
|
|||
Hm, worth a look, thanks!
"Dinsdale" > wrote in message ... > On Thu, 2 Jun 2005 20:46:22 -0400, <japhar> wrote: > >>So this is random, but Im scratching my head... trying to find a way to >>mount a little mustang badge on my grille, the badge has little metal >>posts >>that arent quite long enough to reach.. >> >>Is there something that will put a thread on them so I can put on a nut >>and >>a bracket? I.E. the oposite of drilling and tapping a hole, can i thread a >>blank post somehow? >> >>If not, what can I use to bond chromed metal (permanently enough that some >>kid wont yank it off) >> > > You need a die...as in "tap and die set" > > However, since those emblems are fairly soft metal, and the post > diameter small, a die might not work. > > I've see some emblems held on with a stamped-steel, self-tapping nut > similar to those pictured on this site: > http://www.boltproducts.com/tinnerma...peed-nuts.html > (look a the 'Palnut' models) > > DP > Pics of the cars: > http://tinyurl.com/d2q9u |
#8
|
|||
|
|||
The grille is billet..
I was going to use tape, except the damn badge is hollow, and has a ton of curves. JB weld is what the guy said to use, but im not wild about using superglue on my baby. "SVTKate" > wrote in message link.net... > What kind of grille do you have? > > I have a billet gille on mine. > I put a Cobra emblem in the middle of it. > I used Automotive two sided tape, just like they use to attach the side > emblems, it has held for several years, no problem. > You clean the back really well with alcohol, let it dry. > Over apply it, cut the excess off with a razor blade so that it it trimmed > nicely around the edges of the emblem and stick it on. > > BUT my grille IS metal. > > The posts are very soft, if you try to thread one, you may have it break > off. > You MIGHT be able to use something like JB weld (or some sort of really > good > glue) screws to the back of the emblem > or something like that if the back of the emblem is hollow > > <japhar> wrote in message ... > | So this is random, but Im scratching my head... trying to find a way to > | mount a little mustang badge on my grille, the badge has little metal > posts > | that arent quite long enough to reach.. > | > | Is there something that will put a thread on them so I can put on a nut > and > | a bracket? I.E. the oposite of drilling and tapping a hole, can i thread > a > | blank post somehow? > | > | If not, what can I use to bond chromed metal (permanently enough that > some > | kid wont yank it off) > | > | > > |
#9
|
|||
|
|||
Damn, thats a really good idea.
".boB" > wrote in message . com... > japhar wrote: >> So this is random, but Im scratching my head... trying to find a way to >> mount a little mustang badge on my grille, the badge has little metal >> posts that arent quite long enough to reach.. >> >> Is there something that will put a thread on them so I can put on a nut >> and a bracket? I.E. the oposite of drilling and tapping a hole, can i >> thread a blank post somehow? >> >> If not, what can I use to bond chromed metal (permanently enough that >> some kid wont yank it off) > > Get a piece of tubing that fit's over the posts, and extends past the > post ends about 1/4". Get a screw (like #10), that is the same diameter > as the post, and cut the head off. The screw should fit in the tube, and > the tube should fit over the end of the post. Use JB Weld to hold it all > together. I would even dril a couple of transverse holes in the tube to > allow the JB Weld to spooge out and make a stronger bond and prevent air > pockets. > > -- > .boB > 1997 HD FXDWG - Turbocharged! > 2001 Dodge Dakota QC 5.9/4x4/3.92 > 1966 Mustang Coupe - Daily Driver > 1966 FFR Cobra - Ongoing project > |
#10
|
|||
|
|||
> ".boB" > wrote in message >> Get a piece of tubing that fit's over the posts, and extends past the >>post ends about 1/4". Get a screw (like #10), that is the same diameter >>as the post, and cut the head off. The screw should fit in the tube, and >>the tube should fit over the end of the post. Use JB Weld to hold it all >>together. I would even dril a couple of transverse holes in the tube to >>allow the JB Weld to spooge out and make a stronger bond and prevent air >>pockets. Hhhhhuh, huhuhuh hhuuh huhh he thaid "spooge", huh huhuhuh.... -- 3am is _never_ a good hour for a summoning - a moment of lost concentration and you've got Nader instead of Nyarlathotep. Amphetamines are not a good idea either: unsafe at any speed. - Cadbury Moose |
Thread Tools | |
Display Modes | |
|
|