If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
96 Town & Country Oxygen Sensor
I need to change my upper (manifold) O2 sensor and I can just see it from
under the vehicle way up on top of the rear manifold. Anyone have any proceedures for getting to it? It looks like I need to drop the engine or something drastic like that to get to it. Help! |
Ads |
#2
|
|||
|
|||
Before dropping the engine......take it to a shop and ask them to get it
off, its easier to raise the vehicle then pull the engine Glenn Beasley Chrysler Tech "techdrive" > wrote in message lkaboutautos.com... > I need to change my upper (manifold) O2 sensor and I can just see it from > under the vehicle way up on top of the rear manifold. Anyone have any > proceedures for getting to it? It looks like I need to drop the engine or > something drastic like that to get to it. Help! > |
#3
|
|||
|
|||
Before dropping the engine......take it to a shop and ask them to get it
off, its easier to raise the vehicle then pull the engine Glenn Beasley Chrysler Tech "techdrive" > wrote in message lkaboutautos.com... > I need to change my upper (manifold) O2 sensor and I can just see it from > under the vehicle way up on top of the rear manifold. Anyone have any > proceedures for getting to it? It looks like I need to drop the engine or > something drastic like that to get to it. Help! > |
#4
|
|||
|
|||
Do you know a proceedure? I was hoping to keep out of the shop if possible
sparing funds. Thanks |
#5
|
|||
|
|||
Do you know a proceedure? I was hoping to keep out of the shop if possible
sparing funds. Thanks |
#6
|
|||
|
|||
well you never did say what engine it has?? if its the 3.3/3.8 with a
specail wrench you may be able to get it from the top, "techdrive" > wrote in message lkaboutautos.com... > Do you know a proceedure? I was hoping to keep out of the shop if possible > sparing funds. Thanks > |
#7
|
|||
|
|||
well you never did say what engine it has?? if its the 3.3/3.8 with a
specail wrench you may be able to get it from the top, "techdrive" > wrote in message lkaboutautos.com... > Do you know a proceedure? I was hoping to keep out of the shop if possible > sparing funds. Thanks > |
#8
|
|||
|
|||
Thanks, It is the 3.8, forgot to mention that.
|
#9
|
|||
|
|||
Thanks, It is the 3.8, forgot to mention that.
|
#10
|
|||
|
|||
if you have a new one then cut the wires off at the sensor so u can use
a regular socket to remove it from underneath just jack it up techdrive wrote: > Thanks, It is the 3.8, forgot to mention that. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Climatronic Diagnostic Controls | Luís Lourenço | Audi | 1 | November 12th 04 08:22 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 10 | October 16th 04 05:28 AM |
Oxygen sensor problem | Loki | Audi | 6 | October 10th 04 04:16 PM |
2004 Chrysler Town and Country Minivan | Bob | Dodge | 5 | April 25th 04 03:47 AM |