![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]() I'd like to replace the tail light/brake light bulbs and front turn signal bulbs in my 64 Chrysler with LEDs. Do they make LEDs that just plug into the same sockets or do I have to make changes? Any web site I can visit to see these LEDs? |
Ads |
#2
|
|||
|
|||
![]()
You can get 1replacements in various envelope sizes/LED counts at truck
stops and some auto-parts stores. They come in various colors, and sometimes a colored LED appears clear when turned off, so examine the label carefully to make sure you're buying the right thing. Some of them carry fine print that says they aren't Department of Transportation approved, for what that's worth (guess it depends on how nitpicking a cop or a safety inspector feels). This may be different for the replacement bulbs than for whole sealed units in standard truck sizes and shapes -- *those* seem to be just taking over the world lately, probably because of greater reliability. Maybe Daniel Stern can comment more on these matters. Prices seem to be coming down some but are still in the range of $6 a bulb, and if memory serves a '64 Chrysler has a fair number of bulbs, so this isn't going to be a cheap exercise. I'm thinking about buying one for my retrofitted center high-mount stop lamp, so that I (or, more to the point, people behind me) can get the benefit of its very fast risetime without the three-figure price tag of re-lamping a whole '66 Thunderbird with them. If memory serves, the difference in current draw is in your favor not as great as you might intuitively expect. --Joe |
#3
|
|||
|
|||
![]()
Can you get them in 6 volts
"tranch728" > wrote in message ... > > I'd like to replace the tail light/brake light bulbs and front turn > signal bulbs in my 64 Chrysler with LEDs. Do they make LEDs that just plug > into the same sockets or do I have to make changes? > Any web site I can visit to see these LEDs? > > |
#4
|
|||
|
|||
![]()
Pretty unlikely, as you are paying for a direct replacement package: i.e.
and LED w/ the proper resistor mounted in the correct socket. The good news is that you only need ~ 1.2 volts to turn on an LED. So, it can be done. Dog wrote: > Can you get them in 6 volts > "tranch728" > wrote in message > ... >> >> I'd like to replace the tail light/brake light bulbs and front turn >> signal bulbs in my 64 Chrysler with LEDs. Do they make LEDs that just >> plug into the same sockets or do I have to make changes? >> Any web site I can visit to see these LEDs? >> >> -- FXS_at_beechhurst.com |
#5
|
|||
|
|||
![]() "Robin Banks" > skrev i meddelandet ... > On Tue, 01 Feb 2005 08:00:02 -0500, Frank Scully > > wrote: > >> The good news is that you only need ~ 1.2 volts to turn on an LED > > Depends on the LED. Some are 1.3v, some are 9v, some are 12v. > > All in all though, any 12v LED lamp replacement should work in any 12v > auto, > though I'd think the LED would look a little strange in them. (too > "instant" > on/off for my tastes.) > > > ~~R.Banks You can use 240 volts an d a diod 1N5001 as long as you don't exceed the 20-40 mA. Use the right resistor for the LED and you can use any voltage. look at the specs for the LED. U = R · I U / I = R 12 / 0,03A = 400 Ohm resistor for 6 volts = 200 Ohm resistor P = U * I 12 * 0,03A = 0,36 Watt and for 6 volts = 0,18 Watt Pepe |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
American cars | Dave | Antique cars | 6 | February 13th 05 04:27 PM |
528i vs 530i vs 540i USA Versions | FSJ | BMW | 37 | January 16th 05 06:38 PM |
Dream Cars, The Best Cars in the World | Rare Old Things | Antique cars | 0 | February 14th 04 04:38 AM |
I'd like some opinions on which 35+ years US stationcars are good cars, if any. | Basil | Antique cars | 5 | September 10th 03 10:35 PM |