If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Speedometer repair
I've just failed the second speedometer in as many years in my daily
driven 63. They were both used units so I am looking for someplace that will recondition one for me to as-new condition. Max |
Ads |
#2
|
|||
|
|||
On Mon, 31 Jan 2005 18:18:39 -0700, Max Welton
> wrote: >I've just failed the second speedometer in as many years in my daily >driven 63. They were both used units so I am looking for someplace that >will recondition one for me to as-new condition. > >Max http://www.speedometershop.com/ Hope that Helps. Remove "YOURPANTIES" to reply MUADIB® http://www.angelfire.com/retro/sster...IN%20PAGE.html one small step for man,..... One giant leap for attorneys. |
#3
|
|||
|
|||
On Mon, 31 Jan 2005 18:18:39 -0700 Max Welton
> wrote: >I've just failed the second speedometer in as many years in my daily >driven 63. They were both used units so I am looking for someplace that >will recondition one for me to as-new condition. What actually falied in them? I can usually fix the mechanical problems, but I can't do anything about the cosmetics. - ----------------------------------------------- Jim Adney Madison, WI 53711 USA ----------------------------------------------- |
#4
|
|||
|
|||
Jim Adney wrote:
> On Mon, 31 Jan 2005 18:18:39 -0700 Max Welton > > wrote: > > >>I've just failed the second speedometer in as many years in my daily >>driven 63. They were both used units so I am looking for someplace that >>will recondition one for me to as-new condition. > > > What actually falied in them? The original developed some erratic behaviour of the speedometer needle. At low speeds (stop-and-go traffic) it would surge between 0 and ~40 mph. At moderate vehicle speeds (40 to 55) it seemed stable and reasonable. Starting around 60 mph, the needle would soar erratically up to 80 and back down. The odometer worked fine and I have that unit in a box as a future parts donor. The one in the car now I got from a Samba ad. It's been fine for about a year. No funny noises or odd behaviour. Sunday the speedometer and odometer both stopped working. Like a broken cable. But whem I unhooked the cable from the speedo and pulled on the cable, it was still secure. And it turns out the speedometer may still be OK after all. Last night I had the front of the car up (brake adjustment and snow tire removal) and gave the tire a spin. Turns out the cable is not turning with the dust cap. It's still there, cotter pin in place. Just doesn't turn. It remains to be seen if the speedo is OK. The fit of old cable and dust cap is screwed up for SOME reason. I brought home a new cable and will go out and take a closer look after dinner. Assuming the speedo will still turn I may be able to just weld up the hole in the dust cap and remake the square hole with a drill and tiny file. Max |
#5
|
|||
|
|||
On Tue, 01 Feb 2005 18:39:58 -0700 Max Welton
> wrote: >The original developed some erratic behaviour of the speedometer needle. Make sure the cable spins completely freely while on its own. Note that it actually needs to be "adjusted" after everything is installed. With everything in place and tight, reach under the car and pull the cable housing toward the center of the car, sliding it as far out of the steering knuckle as it will go. Then push it in as far as it will go. Finally, put it midway between these two positions. >And it turns out the speedometer may still be OK after all. Last night I >had the front of the car up (brake adjustment and snow tire removal) and >gave the tire a spin. Turns out the cable is not turning with the dust >cap. It's still there, cotter pin in place. Just doesn't turn. > >It remains to be seen if the speedo is OK. The fit of old cable and dust >cap is screwed up for SOME reason. I brought home a new cable and will >go out and take a closer look after dinner. Assuming the speedo will >still turn I may be able to just weld up the hole in the dust cap and >remake the square hole with a drill and tiny file. Those holes wear for some reason. You can usually just place the cap over a large punch clamped vertically upwards in a vice, then tap the cap with a hammer to work metal back where it came from. It doesn't take much to make this fit nicely again. - ----------------------------------------------- Jim Adney Madison, WI 53711 USA ----------------------------------------------- |
#6
|
|||
|
|||
In article >,
Jim Adney > wrote: > On Mon, 31 Jan 2005 18:18:39 -0700 Max Welton > > wrote: > > >I've just failed the second speedometer in as many years in my daily > >driven 63. They were both used units so I am looking for someplace that > >will recondition one for me to as-new condition. > > What actually falied in them? > > I can usually fix the mechanical problems, but I can't do anything > about the cosmetics. > > - > ----------------------------------------------- > Jim Adney > Madison, WI 53711 USA > ----------------------------------------------- Can you repair the odometer in a 73 Squareback? If so I wish I'd known you when I was in WI. Actually, I wish I'd known you when I was in Madison regardless - particularly since you probably could have warned me not to allow MOFOCO to kill my car |
#7
|
|||
|
|||
On Sun, 13 Mar 2005 03:35:56 GMT mez > wrote:
>In article >, > Jim Adney > wrote: > >> On Mon, 31 Jan 2005 18:18:39 -0700 Max Welton >> > wrote: >> >> >I've just failed the second speedometer in as many years in my daily >> >driven 63. They were both used units so I am looking for someplace that >> >will recondition one for me to as-new condition. >> >> What actually falied in them? >> >> I can usually fix the mechanical problems, but I can't do anything >> about the cosmetics. >Can you repair the odometer in a 73 Squareback? If so I wish I'd known >you when I was in WI. Sure can. No problem >Actually, I wish I'd known you when I was in Madison regardless - >particularly since you probably could have warned me not to allow MOFOCO >to kill my car Sorry about that. Live and learn.... - ----------------------------------------------- Jim Adney Madison, WI 53711 USA ----------------------------------------------- |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Hondo civic, speedometer sensor fuse blowing up | [email protected] | Honda | 3 | January 15th 05 03:48 AM |
New *FREE* Corvette Discussion Forum | JLA ENTERPRISES TECHNOLOGIES INTEGRATION | Corvette | 12 | November 30th 04 07:36 PM |
Consumer Advocacy Organization Takes Aim at Auto Repair Shop Rip-offs. Please Help! | Kenneth Brotman | 4x4 | 2 | January 6th 04 07:21 PM |
1962 Cadillac Eldorado speedometer cable trouble? | Charles Scheffold | Antique cars | 11 | October 13th 03 05:14 AM |