If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
Dana 30
The STOCK '91 and the STOCK '95 have different vacumn hookups and
wiring. Whatever. JimG wrote: > Sure do... works fine. > > "RoyJ" wrote in message... > >>Hook up is the same, but you don't have the '4wd' light on the dash. >> >>JimG wrote: >> >>>I did not have to do that... same hook-up on the vacuum disconnect as the >>>91 axle. >>> >>>"RoyJ" < wrote in message... >>> >>> >>>>Part numbers won't match, the '95 has a slightly different vacmumn motor >>>>setup. Requires moving the wire from the switch on the firewall down to >>>>the switch on the axle. No big deal, just one of those irritating things. >>>> >>>>ufatbastehd wrote: >>>> >>>> >>>>>On Feb 20, 3:30 pm, The Merg wrote: >>>>> >>>>> >>>>> >>>>>>'95 is a YJ, so hypothetically it uses the same ujoints and calipers. >>>>>>I >>>>>>don't think they changed those between 91-95. >>>>>>I'm just guessing, though. >>>>>>Go to a parts website, look up the respective parts for the 91 and the >>>>>>95 and see if the part #s match. >>>>>> >>>>>>ufatbastehd wrote: >>>>>> >>>>>> >>>>>> >>>>>>>I may get a Dana 30 out of a 95YJ for my 91 YJ. >>>>>>>Can I use the calipers from my 91 on the 95 axle? >>>>>> >>>>>>>Also does the 95 have the larger TJ style axle ujoints? >>>>> >>>>> >>>>> >>>>> >>>>>DOH! why did'nt I think of that? >>>>> >>> >>> > |
Ads |
#12
|
|||
|
|||
Dana 30
On Feb 20, 9:40 pm, "JimG" > wrote:
> I did not have to do that... same hook-up on the vacuum disconnect as the 91 > axle. > > "RoyJ" < wrote in message... > > Part numbers won't match, the '95 has a slightly different vacmumn motor > > setup. Requires moving the wire from the switch on the firewall down to > > the switch on the axle. No big deal, just one of those irritating things. > > > ufatbastehd wrote: > >> On Feb 20, 3:30 pm, The Merg wrote: > > >>>'95 is a YJ, so hypothetically it uses the same ujoints and calipers. I > >>>don't think they changed those between 91-95. > >>>I'm just guessing, though. > >>>Go to a parts website, look up the respective parts for the 91 and the > >>>95 and see if the part #s match. > > >>>ufatbastehd wrote: > > >>>>I may get a Dana 30 out of a 95YJ for my 91 YJ. > >>>>Can I use the calipers from my 91 on the 95 axle? > > >>>>Also does the 95 have the larger TJ style axle ujoints? > > >> DOH! why did'nt I think of that? I'm using my existing disco so it should just bolt right up with no wiring BS |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
will dana 35 brakes work with dana 44 axle | [email protected] | Jeep | 8 | March 10th 06 06:10 PM |
Dana 33,Dana 44, & Dana 60 How to tell apart. | [email protected] | 4x4 | 6 | April 12th 05 11:53 PM |
PTO for Dana 20 | Willy Schneider | Jeep | 2 | February 6th 05 02:12 AM |
Dana 44 turns into Dana $2000 | Rushfn1 | Jeep | 18 | February 4th 05 06:31 AM |
1992 F250 Dana 44 or Dana 50? | Matt Vorne | 4x4 | 0 | October 28th 04 11:54 PM |