A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » VW water cooled
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Cold Start sequence for VW diesel engine (Seat Toledo)



 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #2  
Old October 27th 04, 01:39 AM
Woodchuck
external usenet poster
 
Posts: n/a
Default

Turn the key on and crank it after the glow plug lamp goes out. From memory
the glow plugs will stay on after startup to help it run smoother. Also the
3 glow plug in the water jacket stay on to help get heat sooner. As to if
the plugs are sticking on... well I guess so but one would need to connect a
volt meter and see if they all go out after the engine is warm


"MikeyB" > wrote in message
m...
> Does any own know the cold start sequence for 1997 (VW) 1.9 Diesel
> engine from a Seat Toledo SE.
> - Engine No: 1Y0698861
> - Spares No: R000570
> - The same engine is also used by VW cars but I'm not sure which.
>
> From cold:
> 1. Trickle current when driver's door is opened and closed
> (glow plugs).
> 2. Full current for a few seconds once ignition is turned on
> (glow plugs).
> 3. Then no current.
> 4. Full current returns for appox. 3 mins once engine starts.
> Until engine warms up.(glow plugs?)
>
> Warm start:
> As above but full power remains for less than 3 mins depending on how
> recently the car was used.
>
> I am trying to work out if the large amount of current taken during
> the latter heating period (approx 3 mins) is "normal" or the battery (
> which was old anyway) broke through normal ware and tear.
> (I am assuming this 3 mins heating is for the glow plugs - it seems an
> awfully long time.)
>
> I had a flat battery and a burnt out fuse. I have been told by a car
> mechanic that current should only heat the glow plugs for a few
> seconds rather than a few minutes and the reason why the battery is
> flat is because the glow plugs are heated for too long.
>
> Also if any one knows where I can get a wiring diagram for this car
> too.
> (Haynes don't do a manual for this model)
>
> Or if you know of any other cars that this engine is also used on it
> would be a help - I could have a look in the Haynes manual for that
> car.
>
> Thanks
>
> MikeyB



 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
rec.autos.makers.chrysler FAQ, Part 1/6 Dr. David Zatz Chrysler 7 February 1st 05 02:43 PM
rec.autos.makers.chrysler FAQ, Part 1/6 Dr. David Zatz Chrysler 10 January 2nd 05 06:15 AM
rec.autos.makers.chrysler FAQ, Part 1/6 Dr. David Zatz Chrysler 10 December 2nd 04 06:19 AM
rec.autos.makers.chrysler FAQ, Part 1/6 Dr. David Zatz Chrysler 10 November 16th 04 06:28 AM


All times are GMT +1. The time now is 02:55 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.