A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Honda
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Loose caliper on Integra?



 
 
Thread Tools Display Modes
  #1  
Old June 21st 05, 04:42 AM
RkFast
external usenet poster
 
Posts: n/a
Default Loose caliper on Integra?

95 Teg LS....

Did a complete brake job, including two new rear calipers (old ones were
binding up pretty good). About a month after I finished the job, I'm hearing
a pretty loud knocking from the rear when going slow over bumps. Noise goes
away when I depress brake pedal or pull on e-brake handle a few clicks. So I
dive underneath and start pulling on things to see what's loose. Get to the
calipers and when I pulled on them by the brake hose boss and giggle, they
deflect a good 1/8 -1/4 of an inch back and forth!

That's not right, is it? No car I've ever worked on had their calipers move
at all, even when retracted. I'm thinking the rebuilder did a lousy job and
used wrong hardware...surprising ,but I guess possible.

Thoughts?


Ads
  #2  
Old June 21st 05, 06:04 AM
disallow via CarKB.com
external usenet poster
 
Posts: n/a
Default

After getting the front brake pads done on my 98 civic, I noticed a clunk
when I went over bumps as well. It ended up being the way the pads fit in
there, maybe honda changed manufacturers or something, cuz those pads just
don't fit in there properly.

I took it back to the dealership and they tried to make it better, (and
succeeded, I think by bending some of the shims a little). However, now its
about 30000kms later, and I notice a 'click' upon acceleration and another
pronounced 'click' when I decelerate. This only happens in 1st and 2nd gear,
i guess the other gears the deceleration is more gradual. The only thing I
can trace it down to is that the pads are shifting inside the caliper. I
checked my driveshafts, and the outer joints on both are super tight,
otherwise i would have suspected that. I have also replace a tie rod end on
the driver side, it was toast, but did not solve the clicking.

Thats what I came up with anyways. Any other thoughts out there?

RkFast wrote:
>95 Teg LS....
>
>Did a complete brake job, including two new rear calipers (old ones were
>binding up pretty good). About a month after I finished the job, I'm hearing
>a pretty loud knocking from the rear when going slow over bumps. Noise goes
>away when I depress brake pedal or pull on e-brake handle a few clicks. So I
>dive underneath and start pulling on things to see what's loose. Get to the
>calipers and when I pulled on them by the brake hose boss and giggle, they
>deflect a good 1/8 -1/4 of an inch back and forth!
>
>That's not right, is it? No car I've ever worked on had their calipers move
>at all, even when retracted. I'm thinking the rebuilder did a lousy job and
>used wrong hardware...surprising ,but I guess possible.
>
>Thoughts?



--
Message posted via http://www.carkb.com
  #3  
Old June 21st 05, 11:19 AM
RkFast
external usenet poster
 
Posts: n/a
Default

This isn't the pad moving, its caliper itself. You can grab hold of it,
wiggle it back and forth and see it move.

The only thing I can think of is that the rebuilder user the incorrect size
slider pins.

"disallow via CarKB.com" > wrote in message
...
> After getting the front brake pads done on my 98 civic, I noticed a clunk
> when I went over bumps as well. It ended up being the way the pads fit in
> there, maybe honda changed manufacturers or something, cuz those pads just
> don't fit in there properly.
>
> I took it back to the dealership and they tried to make it better, (and
> succeeded, I think by bending some of the shims a little). However, now
> its
> about 30000kms later, and I notice a 'click' upon acceleration and another
> pronounced 'click' when I decelerate. This only happens in 1st and 2nd
> gear,
> i guess the other gears the deceleration is more gradual. The only thing
> I
> can trace it down to is that the pads are shifting inside the caliper. I
> checked my driveshafts, and the outer joints on both are super tight,
> otherwise i would have suspected that. I have also replace a tie rod end
> on
> the driver side, it was toast, but did not solve the clicking.
>
> Thats what I came up with anyways. Any other thoughts out there?
>
> RkFast wrote:
>>95 Teg LS....
>>
>>Did a complete brake job, including two new rear calipers (old ones were
>>binding up pretty good). About a month after I finished the job, I'm
>>hearing
>>a pretty loud knocking from the rear when going slow over bumps. Noise
>>goes
>>away when I depress brake pedal or pull on e-brake handle a few clicks. So
>>I
>>dive underneath and start pulling on things to see what's loose. Get to
>>the
>>calipers and when I pulled on them by the brake hose boss and giggle, they
>>deflect a good 1/8 -1/4 of an inch back and forth!
>>
>>That's not right, is it? No car I've ever worked on had their calipers
>>move
>>at all, even when retracted. I'm thinking the rebuilder did a lousy job
>>and
>>used wrong hardware...surprising ,but I guess possible.
>>
>>Thoughts?

>
>
> --
> Message posted via http://www.carkb.com



  #4  
Old June 21st 05, 12:07 PM
Professor
external usenet poster
 
Posts: n/a
Default

Maybe missing anti-rattle clips for caliper slide if equipped?

Professor
Check out FlashAlert at www.telstar-electronics.com

  #5  
Old June 21st 05, 12:54 PM
RkFast
external usenet poster
 
Posts: n/a
Default

Nope...they are there.

"Professor" > wrote in message
oups.com...
> Maybe missing anti-rattle clips for caliper slide if equipped?
>
> Professor
> Check out FlashAlert at www.telstar-electronics.com
>



  #6  
Old June 21st 05, 01:16 PM
Professor
external usenet poster
 
Posts: n/a
Default

Well maybe your incorrect slider pins theory may be correct. There
should be very little slop in the caliper slide mechanism.

Professor
Check out FlashAlert at www.telstar-electronics.com

  #7  
Old June 21st 05, 01:38 PM
TeGGeR®
external usenet poster
 
Posts: n/a
Default

"RkFast" > wrote in :

> 95 Teg LS....
>
> Did a complete brake job, including two new rear calipers (old ones
> were binding up pretty good). About a month after I finished the job,
> I'm hearing a pretty loud knocking from the rear when going slow over
> bumps. Noise goes away when I depress brake pedal or pull on e-brake
> handle a few clicks. So I dive underneath and start pulling on things
> to see what's loose. Get to the calipers and when I pulled on them by
> the brake hose boss and giggle, they deflect a good 1/8 -1/4 of an
> inch back and forth!
>
> That's not right, is it? No car I've ever worked on had their calipers
> move at all, even when retracted. I'm thinking the rebuilder did a
> lousy job and used wrong hardware...surprising ,but I guess possible.
>
> Thoughts?
>
>



Do you mean "back and forth" as in to the front of the car and rearwards,
or to the left and right of the car?

Are you certain the pads are *completely free* on their mount bracket? That
the pistons are moving out properly on both sides?

When you remove the caliper, both pads ought to almost literally fall off
the mount bracket.

Once piston adjustment has been completed, it should be impossible to move
the caliper at all by hand without a hefty push.


--
TeGGeR®

The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
  #8  
Old June 22nd 05, 12:28 AM
TeGGeR®
external usenet poster
 
Posts: n/a
Default

"RkFast" > wrote in :

> 95 Teg LS....
>
> Did a complete brake job, including two new rear calipers (old ones
> were binding up pretty good). About a month after I finished the job,
> I'm hearing a pretty loud knocking from the rear when going slow over
> bumps. Noise goes away when I depress brake pedal or pull on e-brake
> handle a few clicks. So I dive underneath and start pulling on things
> to see what's loose. Get to the calipers and when I pulled on them by
> the brake hose boss and giggle, they deflect a good 1/8 -1/4 of an
> inch back and forth!



And "back and forth" is what? Left to right relative to the car, or front-
to-back relative to the car?

This is important, as it means different problems.


--
TeGGeR®

The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
  #9  
Old June 23rd 05, 03:33 AM
TeGGeR®
external usenet poster
 
Posts: n/a
Default

"RkFast" > wrote in :

> This isn't the pad moving, its caliper itself. You can grab hold of
> it, wiggle it back and forth and see it move.




Which way is "back and forth"? Front-to-back on the car, or left-to-right
on the car?

Those pins are only 3/8" in diameter where they go into the caliper mount
bracket. If you've got up to 1/4" of play, then you've got some *very*
serious issues here.

Once the pistons have extended fully, there ought to be NO play. I suspect
the pistons are not actually extending as they should. I wonder if the
adjusting screws are sticking in the piston and not rotating properly.

--
TeGGeR®

The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
  #10  
Old June 23rd 05, 05:06 AM
RkFast
external usenet poster
 
Posts: n/a
Default

Front to back, left to right...all over the place.

Well, I solved the issue.

Took out a pin and replaced it with NEW one from Acura. The pin was very
loose in the bracket hole. So it appears that whoever did the rebuilt
"bored" out these holes and they are just plain too big. So I went with a
new set of calipers direct from Acura. So far, problem solved. Caliper can
still be moved around a bit...but its much much "tighter".

Thanks, everyone for your help.

"TeGGeR®" > wrote in message
...
> "RkFast" > wrote in :
>
>> This isn't the pad moving, its caliper itself. You can grab hold of
>> it, wiggle it back and forth and see it move.

>
>
>
> Which way is "back and forth"? Front-to-back on the car, or left-to-right
> on the car?
>
> Those pins are only 3/8" in diameter where they go into the caliper mount
> bracket. If you've got up to 1/4" of play, then you've got some *very*
> serious issues here.
>
> Once the pistons have extended fully, there ought to be NO play. I suspect
> the pistons are not actually extending as they should. I wonder if the
> adjusting screws are sticking in the piston and not rotating properly.
>
> --
> TeGGeR®
>
> The Unofficial Honda/Acura FAQ
> www.tegger.com/hondafaq/



 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Heater boxes loose casing Fred VW air cooled 1 April 6th 05 12:35 AM
Reassembly of caliper, to much pressure on outside rotor Vince Technology 6 January 10th 05 11:56 PM
98 accord rear brake caliper John Edwards Technology 4 January 4th 05 04:19 AM
stuck caliper... Abeness Honda 113 December 7th 04 02:22 AM


All times are GMT +1. The time now is 09:52 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.