If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Electric Spark noise from under dash when turning ignition key
2004 Accord 2 door EX-L.
Is it normal that I hear some heavy electric sparking from some relay under the dashboard when I turn the ignition key slower than normal? I took it to the dealership today and they told me (without hearing, just based on description) that that is normal and all hondas do that. If this is normal - does it cause premature relay contacts wear out from all this sparking? |
Ads |
#2
|
|||
|
|||
Electric Spark noise from under dash when turning ignition key
"Pszemol" > wrote in
: > 2004 Accord 2 door EX-L. > > Is it normal that I hear some heavy electric sparking from some relay > under the dashboard when I turn the ignition key slower than normal? Do you hear the "sparking" at the very same time as the Check Engine light comes on and goes off? -- Tegger The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
#3
|
|||
|
|||
Electric Spark noise from under dash when turning ignition key
"Tegger" > wrote in message
... >> 2004 Accord 2 door EX-L. >> >> Is it normal that I hear some heavy electric sparking from some relay >> under the dashboard when I turn the ignition key slower than normal? > > > > Do you hear the "sparking" at the very same time as the Check Engine light > comes on and goes off? No, "check engine" light stays solid on when sparking can be heard. It seems to me that this is not fully engaged starter relay. When I am moving the key slowly to the start position first I hear one subtle relay click which blanks off the radio panel, when I do continue slowly turning the key I hear second subtle relay click which turns off the blower motor and then, when I continue to turn the key slowly I hear the fountain of electric sparks sounds and then the starter engages and the motor starts with no problem. Is there a starter motor relay under my dash on the left side of the steering column? Is it possible that this is what I hear? |
#4
|
|||
|
|||
Electric Spark noise from under dash when turning ignition key
"Pszemol" > wrote in
: > "Tegger" > wrote in message > ... >>> 2004 Accord 2 door EX-L. >>> >>> Is it normal that I hear some heavy electric sparking from some >>> relay under the dashboard when I turn the ignition key slower than >>> normal? >> >> >> >> Do you hear the "sparking" at the very same time as the Check Engine >> light comes on and goes off? > > No, "check engine" light stays solid on when sparking can be heard. > > It seems to me that this is not fully engaged starter relay. > > When I am moving the key slowly to the start position first I hear > one subtle relay click which blanks off the radio panel, when I do > continue slowly turning the key I hear second subtle relay click > which turns off the blower motor and then, when I continue to > turn the key slowly I hear the fountain of electric sparks sounds > and then the starter engages and the motor starts with no problem. > > Is there a starter motor relay under my dash on the left side of > the steering column? Is it possible that this is what I hear? > > Your Main Relay/s is/are in fact in that location. I think you may be turning the key TOO slowly, causing the relay to buzz. The ignition switch is not meant to be between positions for extended lengths of time except during troubleshooting. You are meant to turn the switch to each position fairly quickly. What happens if you 1) turn the key quickly to "I", then wait a bit, then 2) turn it quickly to "II", waiting AT LEAST TWO SECONDS, then 3) turn it quickly to "III" until the engine starts? Any "sparking" noise now? Or just heavy clicks as the Check Engine light comes on and goes off? -- Tegger The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
#5
|
|||
|
|||
Electric Spark noise from under dash when turning ignition key
"Tegger" > wrote in message
... > Your Main Relay/s is/are in fact in that location. > > I think you may be turning the key TOO slowly, causing the relay to buzz. Why is it buzzing instead of staying on in place? It looks to me that too much current is flowing through the ignition contacts! Too much current causes sparks and arcing intermittent/nonexistent current flow through the starter relay, which controls much bigger current and now much more audible buzzing sound. This arcing over time would cause relays to burn... > The ignition switch is not meant to be between positions for extended > lengths of time except during troubleshooting. You are meant to turn the > switch to each position fairly quickly. Hm... I just checked - no matter how slow I try to turn the ignition key in my other car (toyota camry) I am UNABLE to cause any buzzing noise or sparks... At some moment the starter engages and I cannot do anything about it other than just release the pressure on the key and disengage the starter or just keep pressing the ignition key and continue starting. Something is definitelly worse in the honda design if they rely on the driver speed of turning this key to prevent relay arcing... Is honda known for more problems with relays than toyota? > What happens if you > 1) turn the key quickly to "I", then wait a bit, then > 2) turn it quickly to "II", waiting AT LEAST TWO SECONDS, then > 3) turn it quickly to "III" until the engine starts? > > Any "sparking" noise now? > Or just heavy clicks as the Check Engine light comes on and goes off? No noticable arcing when I turn ignition key into the position III *quickly*. Just starter engages and the engine starts. Just because I am not noticing it does not mean it does not happen. The arcing, if it is noticable when turning the key slowly it will be there when turning key quickly, only will last shorter (i.e 50-100ms instead of 500ms). Even short arcing times the number of engine starts = premature failure... |
#6
|
|||
|
|||
Electric Spark noise from under dash when turning ignition key
"Pszemol" > wrote in
: > "Tegger" > wrote in message > ... >> Your Main Relay/s is/are in fact in that location. >> >> I think you may be turning the key TOO slowly, causing the relay to >> buzz. > > Why is it buzzing instead of staying on in place? Because you're forcing the relay's contacts to just barely make contact for too long. It's possible to do this with ANY relay if you do things "just so". > It looks to me that too much current is flowing through the ignition > contacts! No, you're simply turning the key too slowly. Why are you doing this? Are you /trying/ to find trouble where there is none? > > Too much current causes sparks and arcing intermittent/nonexistent > current flow through the starter relay, which controls much bigger > current and now much more audible buzzing sound. > > This arcing over time would cause relays to burn... Well sure, if you insist on being silly about it. In normal use most drivers simply twist the ignition switch right around from "0" to "III" without any pauses at all. (That in itself is bad, but for different reasons.) > >> The ignition switch is not meant to be between positions for extended >> lengths of time except during troubleshooting. You are meant to turn >> the switch to each position fairly quickly. > > Hm... > > I just checked - no matter how slow I try to turn the ignition key in > my other car (toyota camry) I am UNABLE to cause any buzzing noise or > sparks... Different setup. Toyota only engages the fuel pump once the engine is turning, so no current will flow until the engine cranks. > At some moment the starter engages and I cannot do anything > about it other than just release the pressure on the key and disengage > the starter or just keep pressing the ignition key and continue > starting. Of course. At some point you will complete the circuit to the starter solenoid and the starter will engage. You must /really/ be trying to find problems where none exist. > > Something is definitelly worse in the honda design if they rely on > the driver speed of turning this key to prevent relay arcing... You'd think, except that this does not translate into the real world. Nobody other than people trying to find non-existent problems do what you do. > > Is honda known for more problems with relays than toyota? In the days when Honda combined two relays into one, yes. But that was due to the sheer mass of that combination, which mass caused the famous Honda PGM-FI Main Relay problems for so many years. That problem and its solution remains one of the most popular pages on my site. But since ~2005, Honda has split the Main Relay into two parts like everybody else, so the old problems are probably gone for good. > >> What happens if you >> 1) turn the key quickly to "I", then wait a bit, then >> 2) turn it quickly to "II", waiting AT LEAST TWO SECONDS, then >> 3) turn it quickly to "III" until the engine starts? >> >> Any "sparking" noise now? >> Or just heavy clicks as the Check Engine light comes on and goes off? > > No noticable arcing when I turn ignition key into the position III > *quickly*. > Just starter engages and the engine starts. Then everything's just dandy. Maybe you should stop trying to find problems where they don't exist. Do you want to maintain a good relationship with your dealer, or do you want to make them hide under their desks when they see you coming? > > Just because I am not noticing it does not mean it does not happen. > The arcing, if it is noticable when turning the key slowly it will be > there when turning key quickly, only will last shorter (i.e 50-100ms > instead of 500ms). > Even short arcing times the number of engine starts = premature > failure... > It doesn't work that way, sorry. -- Tegger The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
#7
|
|||
|
|||
Electric Spark noise from under dash when turning ignition key
"Tegger" > wrote in message
... > "Pszemol" > wrote in > : > >> "Tegger" > wrote in message >> ... >>> Your Main Relay/s is/are in fact in that location. >>> >>> I think you may be turning the key TOO slowly, causing the relay to >>> buzz. >> >> Why is it buzzing instead of staying on in place? > > > > Because you're forcing the relay's contacts to just barely make contact > for too long. It's possible to do this with ANY relay if you do things > "just so". > > > >> It looks to me that too much current is flowing through the ignition >> contacts! > > > > > No, you're simply turning the key too slowly. > > Why are you doing this? Are you /trying/ to find trouble where there is > none? > > > >> >> Too much current causes sparks and arcing intermittent/nonexistent >> current flow through the starter relay, which controls much bigger >> current and now much more audible buzzing sound. >> >> This arcing over time would cause relays to burn... > > > > > Well sure, if you insist on being silly about it. > > In normal use most drivers simply twist the ignition switch right around > from "0" to "III" without any pauses at all. (That in itself is bad, but > for different reasons.) > > > >> >>> The ignition switch is not meant to be between positions for extended >>> lengths of time except during troubleshooting. You are meant to turn >>> the switch to each position fairly quickly. >> >> Hm... >> >> I just checked - no matter how slow I try to turn the ignition key in >> my other car (toyota camry) I am UNABLE to cause any buzzing noise or >> sparks... > > > > Different setup. Toyota only engages the fuel pump once the engine is > turning, so no current will flow until the engine cranks. Well, not sure if this is the fuel pump problem... it does not consume so much current as the starter motor does. I suspect this to be the 'starter cut relay' which is buzzing in my car. In the car service manual, on page 4-5, there is a wiring diagram which surprises me - there is the ignition switch pictured there, which is powering the starter cut relay coil AND at the same moment also the starter solenoid, consuming a lot of current used to move the starter switch into the ON position. When I compare the same part of the wiring diagram in my toyota camry I see there totally different picture... from the electrical point of view, of course. In toyota, the starter relay coil only is powered from the ignition switch. The starter relay contacts, the ones providing power to the actual starter solenoid, are powered straight from battery and the current flowing through the starter solenoid is NOT flowing through the ignition switch in toyota. >> At some moment the starter engages and I cannot do anything >> about it other than just release the pressure on the key and disengage >> the starter or just keep pressing the ignition key and continue >> starting. > > > > Of course. At some point you will complete the circuit to the starter > solenoid and the starter will engage. You must /really/ be trying to > find problems where none exist. I am not sure if you read this carefully - I am UNABLE to repeat the same in toyota. The key at some point makes the contact and this is it: no buzzing, no arcing - the starter is engaged and it is turning. But it does not happen with honda - at some angle of the turned key the starter relay is just buzzing, not making the contact... The weak ignition switch is strugling to close the circuit of the starter relay coil AND at the same point RELAY'S OWN POWER CONTACTS! This should not happen! I wonder how this wiring diagram looks like in the newer models. Tegger, do you have any newer Accord service manual? 2008 maybe? Would you mind scanning this one manual page for me, please? >> Something is definitelly worse in the honda design if they rely on >> the driver speed of turning this key to prevent relay arcing... > > > > > You'd think, except that this does not translate into the real world. > Nobody other than people trying to find non-existent problems do what > you do. If the problem was non existent than I could not find it... I would not find it with my toyota - because there is no problem there. >> Is honda known for more problems with relays than toyota? > > > > In the days when Honda combined two relays into one, yes. But that was > due to the sheer mass of that combination, which mass caused the famous > Honda PGM-FI Main Relay problems for so many years. That problem and its > solution remains one of the most popular pages on my site. > > But since ~2005, Honda has split the Main Relay into two parts like > everybody else, so the old problems are probably gone for good. My car is registered April 2004. It must have been made earlier than that... >>> What happens if you >>> 1) turn the key quickly to "I", then wait a bit, then >>> 2) turn it quickly to "II", waiting AT LEAST TWO SECONDS, then >>> 3) turn it quickly to "III" until the engine starts? >>> >>> Any "sparking" noise now? >>> Or just heavy clicks as the Check Engine light comes on and goes off? >> >> No noticable arcing when I turn ignition key into the position III >> *quickly*. >> Just starter engages and the engine starts. > > > > Then everything's just dandy. :-)) I wish it was just dandy. It would be dandy if I could not hear this arcing... > Maybe you should stop trying to find problems where they don't exist. Do > you want to maintain a good relationship with your dealer, or do you > want to make them hide under their desks when they see you coming? Well, my "relationship" with the dealer is not really my big concern >> Just because I am not noticing it does not mean it does not happen. >> The arcing, if it is noticable when turning the key slowly it will be >> there when turning key quickly, only will last shorter (i.e 50-100ms >> instead of 500ms). >> Even short arcing times the number of engine starts = premature >> failure... > > > It doesn't work that way, sorry. :-)) and yet honda has the famous relay problems but toyota does not... What a concidinky ;-) |
#8
|
|||
|
|||
Electric Spark noise from under dash when turning ignition key
"Pszemol" > wrote in message
... > In the car service manual, on page 4-5, there is a wiring diagram > which surprises me - there is the ignition switch pictured there, which > is powering the starter cut relay coil AND at the same moment also > the starter solenoid, consuming a lot of current used to move the > starter switch into the ON position. > > When I compare the same part of the wiring diagram in my toyota > camry I see there totally different picture... from the electrical point > of view, of course. In toyota, the starter relay coil only is powered > from the ignition switch. The starter relay contacts, the ones providing > power to the actual starter solenoid, are powered straight from battery > and the current flowing through the starter solenoid is NOT flowing > through the ignition switch in toyota. Here is the illustration, may be a helpful aid to the text above: http://www.flickr.com/photos/3755875...7617280874226/ I am still interested if this part of the wiring diagram changed in 2008. |
#9
|
|||
|
|||
Electric Spark noise from under dash when turning ignition key
"Pszemol" > wrote in message
... > "Pszemol" > wrote in message > ... >> In the car service manual, on page 4-5, there is a wiring diagram >> which surprises me - there is the ignition switch pictured there, which >> is powering the starter cut relay coil AND at the same moment also >> the starter solenoid, consuming a lot of current used to move the >> starter switch into the ON position. >> >> When I compare the same part of the wiring diagram in my toyota >> camry I see there totally different picture... from the electrical point >> of view, of course. In toyota, the starter relay coil only is powered >> from the ignition switch. The starter relay contacts, the ones providing >> power to the actual starter solenoid, are powered straight from battery >> and the current flowing through the starter solenoid is NOT flowing >> through the ignition switch in toyota. > > Here is the illustration, may be a helpful aid to the text above: > http://www.flickr.com/photos/3755875...7617280874226/ > > I am still interested if this part of the wiring diagram changed in 2008. Similar circuit in an old generation toyota camry (pages ST-3, ST-24): http://www.turboninjas.com/camry/st.pdf |
#10
|
|||
|
|||
Electric Spark noise from under dash when turning ignition key
"Pszemol" > wrote in
: > > I am not sure if you read this carefully - I am UNABLE to repeat > the same in toyota. The key at some point makes the contact > and this is it: no buzzing, no arcing - the starter is engaged and > it is turning. > > But it does not happen with honda - at some angle of the turned key > the starter relay is just buzzing, not making the contact... The weak > ignition switch is strugling to close the circuit of the starter relay > coil AND at the same point RELAY'S OWN POWER CONTACTS! > This should not happen! If you're so concerned, why don't you just sell this car and buy another Toyota? There are no TSBs or other known issues with your model's ignition system, so whatever you're seeing isn't the problem you think it is. Maybe that's why the dealership told you nothing was wrong. -- Tegger The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
'97 E36: Odd Noise After Turning Off Ignition | Jed | BMW | 2 | March 10th 07 04:41 PM |
Noise when turning | [email protected] | Technology | 1 | August 29th 06 04:13 AM |
E46 Screeching noise on turning right | DW Manchester | BMW | 2 | June 22nd 06 04:40 AM |
bad noise while turning | HerdFsu | VW air cooled | 1 | August 14th 05 02:08 PM |
300m Noise when turning | Steve | Chrysler | 1 | March 21st 05 08:33 PM |