|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
December 7th 04, 05:32 AM
|
|||
|
|||
90 turbo cravan code 13
I just installed a fresh long block and am now getting error code 13.
Indicating a problem with the map sensor. The engine runs pretty well, but has a slight miss at idle. Is the map sensor shot or should I look elsewhere? The van is a high miler 275k kms. I don't know the history of the van as I bought it with a blown motor. Thanks. 
|
| Ads |
|
#2
December 7th 04, 11:42 AM
|
|||
|
|||
|
The first step is to make sure you have vaccuum at the map sensor,and a
good connection, been so long since i dealt with a map code, i forget if the 13 is vacuum or electrical, But if there is a code, im sure the vehicle is running rich at idle, if you got at least 18 inches at the sensor, a good ground at the (i believe the blue/black wire) and 5 volts at the (i belive the orange wire) the map sensor is bad Glenn Beasley Chrysler tech
|
|
#3
December 7th 04, 11:42 AM
|
|||
|
|||
|
The first step is to make sure you have vaccuum at the map sensor,and a
good connection, been so long since i dealt with a map code, i forget if the 13 is vacuum or electrical, But if there is a code, im sure the vehicle is running rich at idle, if you got at least 18 inches at the sensor, a good ground at the (i believe the blue/black wire) and 5 volts at the (i belive the orange wire) the map sensor is bad Glenn Beasley Chrysler tech
|
|
#4
December 8th 04, 06:03 AM
|
|||
|
|||
|
"damnnickname" > wrote in message lkaboutautos.com... > The first step is to make sure you have vaccuum at the map sensor,and a > good connection, been so long since i dealt with a map code, i forget if > the 13 is vacuum or electrical, But if there is a code, im sure the > vehicle is running rich at idle, if you got at least 18 inches at the > sensor, a good ground at the (i believe the blue/black wire) and 5 volts > at the (i belive the orange wire) the map sensor is bad > Glenn Beasley > Chrysler tech > Thanks.
|
|
#5
December 8th 04, 06:03 AM
|
|||
|
|||
|
"damnnickname" > wrote in message lkaboutautos.com... > The first step is to make sure you have vaccuum at the map sensor,and a > good connection, been so long since i dealt with a map code, i forget if > the 13 is vacuum or electrical, But if there is a code, im sure the > vehicle is running rich at idle, if you got at least 18 inches at the > sensor, a good ground at the (i believe the blue/black wire) and 5 volts > at the (i belive the orange wire) the map sensor is bad > Glenn Beasley > Chrysler tech > Thanks.
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Ferodo brake pad code for 1999 BMW E39 520i | vricardo | BMW | 0 | December 9th 04 02:35 PM |
| Help please radio code and headlamp washing question | yar | Corvette | 12 | October 17th 04 03:59 PM |
| Error code 36 | Rick B. | Corvette | 2 | August 24th 04 02:30 AM |
| problem with Audi a4 1.8t 1997 turbo - do i need a new one? | G | Audi | 0 | May 22nd 04 02:35 PM |
Linear Mode
