A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Chrysler
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Tough technical questions



 
 
Thread Tools Display Modes
  #1  
Old October 13th 04, 03:56 AM
Hairy
external usenet poster
 
Posts: n/a
Default Tough technical questions


"Nomen Nescio" > wrote in message
...
> 1. The application is to install a rotary shaft oil seal in an aluminum
> housing. The configuration of the seal is with a rubber coated outside
> diameter. The fit in the bored housing is a light push fit. I suspect

the
> seal will work loose on its own during service. What is the best way to
> install this seal? Options I've considered include replacing this seal
> constructed with a metal o.d., but this is not normally recommended due to
> the high coefficient of expansion. A more promising solution is to "glue"
> the seal in with Loctite 495, cyanoacrylate adhesive. Will that work?
>


Loctite 609 would be a better choice, IMO. 495 is just common super glue,
and would probably not be suitable for use on oil seals.

> 2. The problem is installing a chain sprocket onto a keyed tapered shaft
> which is then secured with a retaining nut. What is the best practice:
> Install on clean and dry taper, install on greased taper, or apply a high
> strength Loctite 272 to the taper before assembly? The idea is to make a
> good assembly but be able to disassemble with no more than a puller

without
> heat. Am I correct in assuming that the key is designed for indexing but
> the torque is taken up by the taper?


Yes

If the taper is greased, removal is
> easy, but the torque might be passed on to the key and cause localized
> stress and failure. Clean and dry I think is the standard way of

assembly,
> but Loctite application may be in common practice too.
>


I agree with the "clean and dry". If you are worried about it loosening on
the shaft, you could always heat the sprocket in a pan of water before assy,
then immediately torque the nut down. A little 242 on the threads would keep
the nut from loosening.
H


Ads
  #4  
Old October 13th 04, 10:43 PM
Bill Putney
external usenet poster
 
Posts: n/a
Default

Alex Rodriguez wrote:
> In article >,
> says...
>
>
>>2. The problem is installing a chain sprocket onto a keyed tapered shaft
>>which is then secured with a retaining nut. What is the best practice:
>>Install on clean and dry taper, install on greased taper, or apply a high
>>strength Loctite 272 to the taper before assembly? The idea is to make a
>>good assembly but be able to disassemble with no more than a puller without
>>heat. Am I correct in assuming that the key is designed for indexing but
>>the torque is taken up by the taper? If the taper is greased, removal is
>>easy, but the torque might be passed on to the key and cause localized
>>stress and failure. Clean and dry I think is the standard way of assembly,
>>but Loctite application may be in common practice too.

>
>
> I would clean the parts and then add a thin layer of grease. Then torque
> the bolt to specs. Even with gease, you will need a puller to get the
> sprocket off. Because it is a tapered press fit the sprocket will still
> move a bit up the taper.
> ------------
> Alex


I don't have an answer for the specific application, but from a
design/engineering standpoint, I would follow the written procedure as
far as grease or no grease. I say that because, unless there is a
positive stop (a step), the stresses on a tapered fit will go up maybe
an order of magnitude or more for the same bolt/nut torque, possibly
stretching or breaking the sprocket if it was not designted for that
stress (i.e., if it was designed assuming no grease).

Bill Putney
(To reply by e-mail, replace the last letter of the alphabet in my
adddress with the letter 'x')


----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! >100,000 Newsgroups
---= East/West-Coast Server Farms - Total Privacy via Encryption =---
  #5  
Old October 13th 04, 10:43 PM
Bill Putney
external usenet poster
 
Posts: n/a
Default

Alex Rodriguez wrote:
> In article >,
> says...
>
>
>>2. The problem is installing a chain sprocket onto a keyed tapered shaft
>>which is then secured with a retaining nut. What is the best practice:
>>Install on clean and dry taper, install on greased taper, or apply a high
>>strength Loctite 272 to the taper before assembly? The idea is to make a
>>good assembly but be able to disassemble with no more than a puller without
>>heat. Am I correct in assuming that the key is designed for indexing but
>>the torque is taken up by the taper? If the taper is greased, removal is
>>easy, but the torque might be passed on to the key and cause localized
>>stress and failure. Clean and dry I think is the standard way of assembly,
>>but Loctite application may be in common practice too.

>
>
> I would clean the parts and then add a thin layer of grease. Then torque
> the bolt to specs. Even with gease, you will need a puller to get the
> sprocket off. Because it is a tapered press fit the sprocket will still
> move a bit up the taper.
> ------------
> Alex


I don't have an answer for the specific application, but from a
design/engineering standpoint, I would follow the written procedure as
far as grease or no grease. I say that because, unless there is a
positive stop (a step), the stresses on a tapered fit will go up maybe
an order of magnitude or more for the same bolt/nut torque, possibly
stretching or breaking the sprocket if it was not designted for that
stress (i.e., if it was designed assuming no grease).

Bill Putney
(To reply by e-mail, replace the last letter of the alphabet in my
adddress with the letter 'x')


----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! >100,000 Newsgroups
---= East/West-Coast Server Farms - Total Privacy via Encryption =---
  #6  
Old October 13th 04, 11:52 PM
Eightupman
external usenet poster
 
Posts: n/a
Default

FYI....."cyanoacrylate" = Super Glue. while superglue bonds a lot of low
stress applications, I do not think that the brittle properties of that
adhesive will accomplish your desired task.

As far as I know the dry taper and the keyway is all you need. As long as
the keyway fits snug into the shaft, part of it's purpose is to prevent
rotation.


"Nomen Nescio" > wrote in message
...
> 1. The application is to install a rotary shaft oil seal in an aluminum
> housing. The configuration of the seal is with a rubber coated outside
> diameter. The fit in the bored housing is a light push fit. I suspect

the
> seal will work loose on its own during service. What is the best way to
> install this seal? Options I've considered include replacing this seal
> constructed with a metal o.d., but this is not normally recommended due to
> the high coefficient of expansion. A more promising solution is to "glue"
> the seal in with Loctite 495, cyanoacrylate adhesive. Will that work?
>
> 2. The problem is installing a chain sprocket onto a keyed tapered shaft
> which is then secured with a retaining nut. What is the best practice:
> Install on clean and dry taper, install on greased taper, or apply a high
> strength Loctite 272 to the taper before assembly? The idea is to make a
> good assembly but be able to disassemble with no more than a puller

without
> heat. Am I correct in assuming that the key is designed for indexing but
> the torque is taken up by the taper? If the taper is greased, removal is
> easy, but the torque might be passed on to the key and cause localized
> stress and failure. Clean and dry I think is the standard way of

assembly,
> but Loctite application may be in common practice too.
>



  #7  
Old October 13th 04, 11:52 PM
Eightupman
external usenet poster
 
Posts: n/a
Default

FYI....."cyanoacrylate" = Super Glue. while superglue bonds a lot of low
stress applications, I do not think that the brittle properties of that
adhesive will accomplish your desired task.

As far as I know the dry taper and the keyway is all you need. As long as
the keyway fits snug into the shaft, part of it's purpose is to prevent
rotation.


"Nomen Nescio" > wrote in message
...
> 1. The application is to install a rotary shaft oil seal in an aluminum
> housing. The configuration of the seal is with a rubber coated outside
> diameter. The fit in the bored housing is a light push fit. I suspect

the
> seal will work loose on its own during service. What is the best way to
> install this seal? Options I've considered include replacing this seal
> constructed with a metal o.d., but this is not normally recommended due to
> the high coefficient of expansion. A more promising solution is to "glue"
> the seal in with Loctite 495, cyanoacrylate adhesive. Will that work?
>
> 2. The problem is installing a chain sprocket onto a keyed tapered shaft
> which is then secured with a retaining nut. What is the best practice:
> Install on clean and dry taper, install on greased taper, or apply a high
> strength Loctite 272 to the taper before assembly? The idea is to make a
> good assembly but be able to disassemble with no more than a puller

without
> heat. Am I correct in assuming that the key is designed for indexing but
> the torque is taken up by the taper? If the taper is greased, removal is
> easy, but the torque might be passed on to the key and cause localized
> stress and failure. Clean and dry I think is the standard way of

assembly,
> but Loctite application may be in common practice too.
>



  #8  
Old October 15th 04, 09:54 AM
Scott M
external usenet poster
 
Posts: n/a
Default


"Nomen Nescio" > wrote in message
...
> Thank you all for your advice.
>
> Do you think a steel cased oil seal will work satisfactorily in aluminum
> alloy if the seal is a good press fit? I would apply a light coat of
> Permatex #1 or Permatex Aviation to the outside diameter before driving it
> home.
>
> I am working on an obsolete motorcycle. The supplier has on hand
> elastomer
> coated o.d. oil seals, but the retention in the bore is problematic. I
> don't think OEM stuff is available and he is supplying generic parts. If
> that is the case, my automotive supplier can special order any seals I
> want
> by size and type specification, so the decision can be made to go with a
> conventional metal case seal. Rubber coated o.d. is supposed to be ideal
> for aluminum alloy, but I don't see any reliability in these seals if I
> can
> literally push into place by hand with essentially no mechanical
> retention.


put a little silicon on the outide of the rubber coated seal and then you
could pean it in a bit with a punch.....just another option.


  #9  
Old October 15th 04, 09:54 AM
Scott M
external usenet poster
 
Posts: n/a
Default


"Nomen Nescio" > wrote in message
...
> Thank you all for your advice.
>
> Do you think a steel cased oil seal will work satisfactorily in aluminum
> alloy if the seal is a good press fit? I would apply a light coat of
> Permatex #1 or Permatex Aviation to the outside diameter before driving it
> home.
>
> I am working on an obsolete motorcycle. The supplier has on hand
> elastomer
> coated o.d. oil seals, but the retention in the bore is problematic. I
> don't think OEM stuff is available and he is supplying generic parts. If
> that is the case, my automotive supplier can special order any seals I
> want
> by size and type specification, so the decision can be made to go with a
> conventional metal case seal. Rubber coated o.d. is supposed to be ideal
> for aluminum alloy, but I don't see any reliability in these seals if I
> can
> literally push into place by hand with essentially no mechanical
> retention.


put a little silicon on the outide of the rubber coated seal and then you
could pean it in a bit with a punch.....just another option.


  #10  
Old October 15th 04, 12:49 PM
Repairman
external usenet poster
 
Posts: n/a
Default

Use the rubber coated ones and the Permatex to help hold it.
You will get galvanic action between the steel and aluminum with the
non-coated ones. That's why the OEM ones are rubber coated to prevent that
corrosion from happening. You don't want the cases to corrode and get pitted
in the seal area after time goes by.
A 2 stroke motor has retainer plates to hold the seals in as they have
pressurized bottom ends, not a problem with a vented 4 stroke crankcase.
--
John
"anything you say can & will be misquoted & used against you"
'01 FLHR ''Red"
'04 MXZ 600ho
'99 XC700
BRC mem

"Nomen Nescio" > wrote in message
...
> Thank you all for your advice.
>
> Do you think a steel cased oil seal will work satisfactorily in aluminum
> alloy if the seal is a good press fit? I would apply a light coat of
> Permatex #1 or Permatex Aviation to the outside diameter before driving it
> home.
>
> I am working on an obsolete motorcycle. The supplier has on hand
> elastomer
> coated o.d. oil seals, but the retention in the bore is problematic. I
> don't think OEM stuff is available and he is supplying generic parts. If
> that is the case, my automotive supplier can special order any seals I
> want
> by size and type specification, so the decision can be made to go with a
> conventional metal case seal. Rubber coated o.d. is supposed to be ideal
> for aluminum alloy, but I don't see any reliability in these seals if I
> can
> literally push into place by hand with essentially no mechanical
> retention.
>



 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Questions, questions, questions Vernon Balbert BMW 15 January 16th 05 04:01 AM
Where to get Official Speed Limit Info [email protected] Driving 40 January 3rd 05 08:10 AM
First BMW - 318iS - few questions? Kevin Rhodes BMW 5 November 16th 04 11:02 PM
E36 Wheels and Suspension questions Jim P. BMW 4 November 11th 04 06:35 PM
Some more newbie questions Ypnos Alfa Romeo 7 June 23rd 04 10:35 AM


All times are GMT +1. The time now is 10:11 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.