A Fishkeeping forum. FishKeepingBanter.com

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » FishKeepingBanter.com forum » ponds » General
Site Map Home Authors List Search Today's Posts Mark Forums Read Web Partners

Air Manifold and Taps : 55 gal drum



 
 
Thread Tools Display Modes
  #1  
Old March 27th 04, 08:13 AM
Snooze
external usenet poster
 
Posts: n/a
Default Air Manifold and Taps : 55 gal drum


"Drew Cutter" wrote in message
...
How do you add a air manifold and tap to a 55 gal drum (plastic) ?
Pictures ?


I made a tap 2 different ways. The first way is kind of crummy and doesn't
as well as I hoped (but good enough)

Method 1
You'll need
1: 3/4" nipple, stainless steel from a plumbing supply is preferred but
galvanized will do.
2: 3/4" pvc threaded couplers (schedule 40)
3: 3/4" garden hose faucet (may need some adaptors)
4: a roll of Teflon tape.
5: a tube of aquarium caulking (not kitchen/bath or window)

Procedure
1: Drill a 3/4" hole into the drum
2: wrap half of the nipple with Teflon tape
3: Screw the pvc coupler as far as you can onto the taped nipple. You'll
need to go as close to the halfway point as possible. So you'll need 2
wrenches and a buddy.
4: Push the nipple through the hole with the pvc coupler side on the inside
of the drum
5: screw on the garden hose faucet on the other side as tightly as possible.
6: seal the gaps around the drum to make it water tight

Method 2
You'll need
1: two 3/4" schedule 40 couplers
2: a foot of 3/4" schedule 40 pipe
3: 3/4" schedule 40 valve
4: 1 bottle schedule 40 cleaner
5: 1 bottle schedule 40 solvent
6: pipe cutters
7: a tube of aquarium caulking (not kitchen/bath or window)

Procedure
1: Drill a 3/4" hole into the drum
2: cut a about 3" section of pipe
3: clean 1 end of the pipe and 1 end of the coupler with the cleaner
4: apply the solvent to the pipe and coupler
5: push the pipe into the coupler as far in as you can
6: push the pipe through hole, and repeat.
Note steps 4 and 5 have to be done quickly (the solvent sets very quickly)
7: seal the gaps around the hole with aquarium caulking

In my examples I used 3/4" pipe, which is fine as a drain for emptying the
drums during cleaning, but you'll need at least 1.5 or 2" pipe for your main
plumbing.

Good luck
Sameer


  #2  
Old March 27th 04, 01:40 PM
A.N.Other
external usenet poster
 
Posts: n/a
Default Air Manifold and Taps : 55 gal drum

"Drew Cutter" wrote in message
...
How do you add a air manifold and tap to a 55 gal drum (plastic) ?
Pictures ?


Some questions:
Why do you want add a manifold?
How much air?
Where is the air coming from?
I am assuming that the drum is vertical how deep is the liquid inside the
drum?
Is the drum complete or has the top been cut off?







  #3  
Old March 27th 04, 01:40 PM
A.N.Other
external usenet poster
 
Posts: n/a
Default Air Manifold and Taps : 55 gal drum

"Drew Cutter" wrote in message
...
How do you add a air manifold and tap to a 55 gal drum (plastic) ?
Pictures ?


Some questions:
Why do you want add a manifold?
How much air?
Where is the air coming from?
I am assuming that the drum is vertical how deep is the liquid inside the
drum?
Is the drum complete or has the top been cut off?







 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 04:31 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2004-2018 FishKeepingBanter.com.
The comments are property of their posters.