If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Geo Metro Gauge problems
Hi,
I have a Geo Metro (1992, 2 door, 3 cylinder) and the fuel and temperature gauges have started to act crazy. The temperature gauge was particularly alarming because it indicated that the car was overheating. I had a mechanic check it and he said the temperature is fine and that the gauges are probably broken. He said it would cost ~$200 to fix it. He also said as long as I keep an eye on the coolant and keep the gas tank full, that I can probably leave it broken. He didn't seem too enthusiastic about my idea to replace the engine with a rebuilt. I bought the car with abtou 81,000 miles on it and had to get the engine essentially rebuilt after buying it. Since then, I've put over 100,000 miles on the car. It still gets 50 mpg and runs quite well. The mechanic, in Pennsylvania where I now live, said that the body is probably in bad shape, but he didn't check it. I moved from Montana where they don't salt the street, so corosion is not as bad there. Any thoughts and opinions about the gauges or the rebuilt engine idea? I can't afford a new car and I don't want to buy a used car because they are typically in bad shape and require a lot of work initially. At least with a rebuilt engine, I'd know the engine is OK. I travel quite a bit, about 1200 miles per month, and am worried my car's days are coming to an end. Thank you for your help and advice. By the way, I don't know anything about car engines and repair, so please be patient with me. Sincerely, Heath |
Ads |
#2
|
|||
|
|||
|
#4
|
|||
|
|||
On Wed, 09 Feb 2005 19:23:32 -0500, Nate Nagel >
wrote: >Lawrence Glickman wrote: > >> On 9 Feb 2005 15:51:23 -0800, wrote: >> >> >>>Hi, >>>I have a Geo Metro (1992, 2 door, 3 cylinder) and the fuel and >>>temperature gauges have started to act crazy. The temperature gauge was >>>particularly alarming because it indicated that the car was >>>overheating. I had a mechanic check it and he said the temperature is >>>fine and that the gauges are probably broken. He said it would cost >>>~$200 to fix it. He also said as long as I keep an eye on the coolant >>>and keep the gas tank full, that I can probably leave it broken. >> >> >> I sort of agree with this to this point. But I've seen gauge kits at >> car parts stores that have all you need >> fuel >> amperes >> oil pressure >> >> and the only question I have is how to hook them up to the sensors. >> That is going to be the tough part of the job. The gauges are cheap >> enough, but finding out how to hook them up to the sensors for those >> things is a mystery unless you know someone who is familiar with your >> particular automobile. Maybe the instructions that come with the kit >> have the instructions, don't know. >> >> >>>He didn't seem too enthusiastic about my idea to replace the engine >>>with a rebuilt. I bought the car with abtou 81,000 miles on it and had >>>to get the engine essentially rebuilt after buying it. Since then, I've >>>put over 100,000 miles on the car. It still gets 50 mpg and runs quite >>>well. The mechanic, in Pennsylvania where I now live, said that the >>>body is probably in bad shape, but he didn't check it. >> >> >> I've driven cars where you could see the road beneath you if you >> looked down from the driver's seat. So? I never fell out of one, >> although I =did= get a ticket in Pennsylvania from a cop who said >> something about my car needing to have something on it fixed, can't >> remember what now, too many years ago. >> >> >>>I moved from >>>Montana where they don't salt the street, so corosion is not as bad >>>there. >>>Any thoughts and opinions about the gauges or the rebuilt engine idea? >> >> >> Engine is probably OK in my opinion. >> If you need a gauge kit, see above. BTW, getting it fixed for less >> than $200 sounds like a hell of a bargain. >> >> >>>I can't afford a new car and I don't want to buy a used car because >>>they are typically in bad shape and require a lot of work initially. At >>>least with a rebuilt engine, I'd know the engine is OK. >>>I travel quite a bit, about 1200 miles per month, and am worried my >>>car's days are coming to an end. >>>Thank you for your help and advice. By the way, I don't know anything >>>about car engines and repair, so please be patient with me. >>>Sincerely, >>>Heath >> >> >> I think if I were in your situation, I would go to a parts store, open >> a box that has a gauge cluster in it, and scope out the installation >> instructions. If it looked like something I could do myself, ( route >> some wires from some sending sensors to the back of the gauge cluster >> ) then I would probably buy the kit, install the wires, and be happy >> about it. >> >> Lg >> > >Don't even bother, just go straight to the junkyard. an IP for a Metro >can't be that desirable an item. > >nate You have to think about the work involved in that. Possibly remove instrument panel from junked Metro Remove instrument panel from OP's car Install instrument panel from JY into OP's car hope everything works. That's a lot of screwdriver work there, maybe you need special torx bits, maybe you have to know where all the fasteners are hidden to begin with. How many times have you thought you had all the screws out and went to pull off a panel only to realize there were more fasteners -somewhere- that had to come out? Sure if OP wants to go through all of this, it will be a great learning experience, but I get the impression he just wants his information back as soon as possible with the least amount of fuss. Lg |
#5
|
|||
|
|||
"Lawrence Glickman" > wrote in message ... > On Wed, 09 Feb 2005 19:23:32 -0500, Nate Nagel > > wrote: > >>Lawrence Glickman wrote: >> >>> On 9 Feb 2005 15:51:23 -0800, wrote: >>> >>> >>>>Hi, >>>>I have a Geo Metro (1992, 2 door, 3 cylinder) and the fuel and >>>>temperature gauges have started to act crazy. The temperature gauge was >>>>particularly alarming because it indicated that the car was >>>>overheating. I had a mechanic check it and he said the temperature is >>>>fine and that the gauges are probably broken. He said it would cost >>>>~$200 to fix it. He also said as long as I keep an eye on the coolant >>>>and keep the gas tank full, that I can probably leave it broken. >>> >>> >>> I sort of agree with this to this point. But I've seen gauge kits at >>> car parts stores that have all you need >>> fuel >>> amperes >>> oil pressure >>> >>> and the only question I have is how to hook them up to the sensors. >>> That is going to be the tough part of the job. The gauges are cheap >>> enough, but finding out how to hook them up to the sensors for those >>> things is a mystery unless you know someone who is familiar with your >>> particular automobile. Maybe the instructions that come with the kit >>> have the instructions, don't know. >>> >>> >>>>He didn't seem too enthusiastic about my idea to replace the engine >>>>with a rebuilt. I bought the car with abtou 81,000 miles on it and had >>>>to get the engine essentially rebuilt after buying it. Since then, I've >>>>put over 100,000 miles on the car. It still gets 50 mpg and runs quite >>>>well. The mechanic, in Pennsylvania where I now live, said that the >>>>body is probably in bad shape, but he didn't check it. >>> >>> >>> I've driven cars where you could see the road beneath you if you >>> looked down from the driver's seat. So? I never fell out of one, >>> although I =did= get a ticket in Pennsylvania from a cop who said >>> something about my car needing to have something on it fixed, can't >>> remember what now, too many years ago. >>> >>> >>>>I moved from >>>>Montana where they don't salt the street, so corosion is not as bad >>>>there. >>>>Any thoughts and opinions about the gauges or the rebuilt engine idea? >>> >>> >>> Engine is probably OK in my opinion. >>> If you need a gauge kit, see above. BTW, getting it fixed for less >>> than $200 sounds like a hell of a bargain. >>> >>> >>>>I can't afford a new car and I don't want to buy a used car because >>>>they are typically in bad shape and require a lot of work initially. At >>>>least with a rebuilt engine, I'd know the engine is OK. >>>>I travel quite a bit, about 1200 miles per month, and am worried my >>>>car's days are coming to an end. >>>>Thank you for your help and advice. By the way, I don't know anything >>>>about car engines and repair, so please be patient with me. >>>>Sincerely, >>>>Heath >>> >>> >>> I think if I were in your situation, I would go to a parts store, open >>> a box that has a gauge cluster in it, and scope out the installation >>> instructions. If it looked like something I could do myself, ( route >>> some wires from some sending sensors to the back of the gauge cluster >>> ) then I would probably buy the kit, install the wires, and be happy >>> about it. >>> >>> Lg >>> >> >>Don't even bother, just go straight to the junkyard. an IP for a Metro >>can't be that desirable an item. >> >>nate > > You have to think about the work involved in that. > Possibly remove instrument panel from junked Metro > Remove instrument panel from OP's car > Install instrument panel from JY into OP's car > hope everything works. > > That's a lot of screwdriver work there, maybe you need special torx > bits, maybe you have to know where all the fasteners are hidden to > begin with. How many times have you thought you had all the screws > out and went to pull off a panel only to realize there were more > fasteners -somewhere- that had to come out? > > Sure if OP wants to go through all of this, it will be a great > learning experience, but I get the impression he just wants his > information back as soon as possible with the least amount of fuss. > > Lg > So you think wiring up an aftermarket fuel gauge would be less work? What makes you think the problem isn't a bad sending unit or wiring? Or does that aftermarket unit you're talking about come with a new fuel sender? Gee.... if that's the case the gas tank has to come out. But hey, at least he won't have wasted 30 minutes replacing his cluster. Unbelievable..... Bob |
#6
|
|||
|
|||
On Wed, 9 Feb 2005 19:15:54 -0600, "Bob" > wrote:
>So you think wiring up an aftermarket fuel gauge would be less work? What >makes you think the problem isn't a bad sending unit or wiring? Or does that >aftermarket unit you're talking about come with a new fuel sender? Gee.... >if that's the case the gas tank has to come out. But hey, at least he won't >have wasted 30 minutes replacing his cluster. Unbelievable..... > Bob What is unbelievable, is you are STILL on my ass. After it like a rabid dog. And like a rabid dog, you should be approached by Animal Control with due caution, and disposed of forthwith. Lg |
#7
|
|||
|
|||
On Wed, 09 Feb 2005 19:28:45 -0600, Lawrence Glickman
> wrote: >On Wed, 9 Feb 2005 19:15:54 -0600, "Bob" > wrote: > > >>So you think wiring up an aftermarket fuel gauge would be less work? What >>makes you think the problem isn't a bad sending unit or wiring? For the same reason I don't think a flock of Mallard Ducks are going to fly out of your ass. What makes you think it IS a bad sending unit or wiring. eh? >>Or does that >>aftermarket unit you're talking about come with a new fuel sender? Gee.... >>if that's the case the gas tank has to come out. But hey, at least he won't >>have wasted 30 minutes replacing his cluster. Unbelievable..... >> Bob Yah, you have quite an imagination, bottom boy. You come up with all kinds of horse**** ideas that have no basis in Reality. Lg |
#8
|
|||
|
|||
"Lawrence Glickman" > wrote in message ... > On Wed, 9 Feb 2005 19:15:54 -0600, "Bob" > wrote: > > >>So you think wiring up an aftermarket fuel gauge would be less work? What >>makes you think the problem isn't a bad sending unit or wiring? Or does >>that >>aftermarket unit you're talking about come with a new fuel sender? Gee.... >>if that's the case the gas tank has to come out. But hey, at least he >>won't >>have wasted 30 minutes replacing his cluster. Unbelievable..... >> Bob > > What is unbelievable, is you are STILL on my ass. > After it like a rabid dog. > > And like a rabid dog, you should be approached by Animal Control with > due caution, and disposed of forthwith. > > Lg > Like I said Larry, I consider it a public service. A lot of the visitors here don't realize how truly stupid most of your ideas are. I'm just doing them a favor by pointing out the stupidest of your ideas. Bob |
#9
|
|||
|
|||
On Wed, 9 Feb 2005 19:49:07 -0600, "Bob" > wrote:
> >"Lawrence Glickman" > wrote in message .. . >> On Wed, 9 Feb 2005 19:15:54 -0600, "Bob" > wrote: >> >> >>>So you think wiring up an aftermarket fuel gauge would be less work? What >>>makes you think the problem isn't a bad sending unit or wiring? Or does >>>that >>>aftermarket unit you're talking about come with a new fuel sender? Gee.... >>>if that's the case the gas tank has to come out. But hey, at least he >>>won't >>>have wasted 30 minutes replacing his cluster. Unbelievable..... >>> Bob >> >> What is unbelievable, is you are STILL on my ass. >> After it like a rabid dog. >> >> And like a rabid dog, you should be approached by Animal Control with >> due caution, and disposed of forthwith. >> >> Lg >> > >Like I said Larry, I consider it a public service. A lot of the visitors >here don't realize how truly stupid most of your ideas are. I'm just doing >them a favor by pointing out the stupidest of your ideas. > Bob > Installing an aftermarket gauge kit is a stupid idea? Well then, you should be spending all your time tomorrow running around to all the auto parts stores telling them to take the products off the shelves instead of wasting your time here in the n/g. THAT would be a Public Service, as soon as the men with the little butterfly nets caught up with you. Lg |
#10
|
|||
|
|||
"Lawrence Glickman" > wrote in message ... > On Wed, 09 Feb 2005 19:28:45 -0600, Lawrence Glickman > > wrote: > >>On Wed, 9 Feb 2005 19:15:54 -0600, "Bob" > wrote: >> >> >>>So you think wiring up an aftermarket fuel gauge would be less work? >>>What >>>makes you think the problem isn't a bad sending unit or wiring? > > For the same reason I don't think a flock of Mallard Ducks are going > to fly out of your ass. > > What makes you think it IS a bad sending unit or wiring. eh? I didn't say it was because I have no idea what his problem is. 20 minutes with a DVOM and a wiring digram and I would know exactly what his problem is though. >>>Or does that >>>aftermarket unit you're talking about come with a new fuel sender? >>>Gee.... >>>if that's the case the gas tank has to come out. But hey, at least he >>>won't >>>have wasted 30 minutes replacing his cluster. Unbelievable..... >>> Bob > > Yah, you have quite an imagination, bottom boy. You come up with all > kinds of horse**** ideas that have no basis in Reality. > > Lg > You're the one who said to go to the parts store and get an aftermarket fuel gauge. Here is your challenge, post a link to an aftermarket gauge that is cheap and will work with the stock Geo sending unit.. Bob |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
various problems with my MX | nytrex | Mazda | 6 | February 7th 05 07:08 PM |
Oil pressure gauge sticking on start-up in cold weather? | Azfreeflyer | Ford Explorer | 6 | December 27th 04 03:22 PM |
FA Air/Fuel Ratio Gauge MK2 and MK3 VW Cars. | Armin B. | VW water cooled | 2 | November 24th 04 07:25 PM |
Audi 100 quattro temp gauge probs | Paul Wickham | Audi | 1 | May 31st 04 04:39 PM |
temperature gauge problems Uk model 1992 K reg 100 2.3 quattro AAR | Paul Wickham | Audi | 0 | May 22nd 04 05:47 PM |