A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Corvette
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Non-Factory Spark Plug Gap Setting



 
 
Thread Tools Display Modes
  #1  
Old October 11th 04, 01:47 AM
Drink
external usenet poster
 
Posts: n/a
Default Non-Factory Spark Plug Gap Setting

Hi All,
Quick question: After modifying the ignition system, is there any logical
method or rule of thumb for changing the factory-recommended spark plug gap?
Engine in question is an '86 Corvette 350cid V8 engine with [305 heads]
TPI, HEI ignition, headers, high voltage coil, "performance" 8mm plug wires.
If anyone can shed more light on the effects of the 305 V8 on the 350
block, I'd appreciate that as well. I think the head casting number is
62426.
Best Regards,
Jim


Ads
  #2  
Old October 11th 04, 01:59 AM
Dad
external usenet poster
 
Posts: n/a
Default


"Drink" > wrote in message
...
> Hi All,
> Quick question: After modifying the ignition system, is there any
> logical method or rule of thumb for changing the factory-recommended spark
> plug gap?
> Engine in question is an '86 Corvette 350cid V8 engine with [305 heads]
> TPI, HEI ignition, headers, high voltage coil, "performance" 8mm plug
> wires.
> If anyone can shed more light on the effects of the 305 V8 on the 350
> block, I'd appreciate that as well. I think the head casting number is
> 62426.
> Best Regards,
> Jim

Any additional gap will depend on whether or not you can produce the voltage
required to jump the gap and still maintain a strong spark.

If you think you have that available open it up a bit and try it. Not as
good as knowing what results you will get because of the work required to
take them out and regap. Go to some of the after market ignition sites and
see what they recommend and at what voltage level.
--
Dad
05 C6 Silver/Red 6spd Z51
72 Shark Black/Black/4spd



  #3  
Old October 11th 04, 01:59 AM
Dad
external usenet poster
 
Posts: n/a
Default


"Drink" > wrote in message
...
> Hi All,
> Quick question: After modifying the ignition system, is there any
> logical method or rule of thumb for changing the factory-recommended spark
> plug gap?
> Engine in question is an '86 Corvette 350cid V8 engine with [305 heads]
> TPI, HEI ignition, headers, high voltage coil, "performance" 8mm plug
> wires.
> If anyone can shed more light on the effects of the 305 V8 on the 350
> block, I'd appreciate that as well. I think the head casting number is
> 62426.
> Best Regards,
> Jim

Any additional gap will depend on whether or not you can produce the voltage
required to jump the gap and still maintain a strong spark.

If you think you have that available open it up a bit and try it. Not as
good as knowing what results you will get because of the work required to
take them out and regap. Go to some of the after market ignition sites and
see what they recommend and at what voltage level.
--
Dad
05 C6 Silver/Red 6spd Z51
72 Shark Black/Black/4spd



  #4  
Old October 11th 04, 06:38 AM
Tom in Missouri
external usenet poster
 
Posts: n/a
Default

When standard points ignitions were the norm, voltage was about 15,000 to
30,000, depending on who you asked. Gap was .035".

When HEI began, there was 60,000 volts and the gap was .060"

HEI dropped to 45,000 for reliability and the gap went to .045".

See a vague pattern?

If you want to check, set up one plug wire and a plug outside the engine
where you can see it. Start the engine and let it run at various RPMs and
see what the spark looks like. A good solid spark that is blue in color
should give you good ignition.

Shut off the engine and open the gap some. (Or set up a video camera and
don't shut off the engine.)

Do this a few times and also try closing the gap. When you find the
strongest spark for the widest gap, go for it. The idea is that a wider gap
exposes more spark and thus more initial flame to the air/fuel mixture.
However, you need a strong spark to break through the mix and to ignite it.
So you have a compromise of wide gap and hottest spark.


"Dad" > wrote in message
...
>
> "Drink" > wrote in message
> ...
> > Hi All,
> > Quick question: After modifying the ignition system, is there any
> > logical method or rule of thumb for changing the factory-recommended

spark
> > plug gap?
> > Engine in question is an '86 Corvette 350cid V8 engine with [305 heads]
> > TPI, HEI ignition, headers, high voltage coil, "performance" 8mm plug
> > wires.
> > If anyone can shed more light on the effects of the 305 V8 on the 350
> > block, I'd appreciate that as well. I think the head casting number is
> > 62426.
> > Best Regards,
> > Jim

> Any additional gap will depend on whether or not you can produce the

voltage
> required to jump the gap and still maintain a strong spark.
>
> If you think you have that available open it up a bit and try it. Not as
> good as knowing what results you will get because of the work required to
> take them out and regap. Go to some of the after market ignition sites and
> see what they recommend and at what voltage level.
> --
> Dad
> 05 C6 Silver/Red 6spd Z51
> 72 Shark Black/Black/4spd
>
>
>


  #5  
Old October 11th 04, 06:38 AM
Tom in Missouri
external usenet poster
 
Posts: n/a
Default

When standard points ignitions were the norm, voltage was about 15,000 to
30,000, depending on who you asked. Gap was .035".

When HEI began, there was 60,000 volts and the gap was .060"

HEI dropped to 45,000 for reliability and the gap went to .045".

See a vague pattern?

If you want to check, set up one plug wire and a plug outside the engine
where you can see it. Start the engine and let it run at various RPMs and
see what the spark looks like. A good solid spark that is blue in color
should give you good ignition.

Shut off the engine and open the gap some. (Or set up a video camera and
don't shut off the engine.)

Do this a few times and also try closing the gap. When you find the
strongest spark for the widest gap, go for it. The idea is that a wider gap
exposes more spark and thus more initial flame to the air/fuel mixture.
However, you need a strong spark to break through the mix and to ignite it.
So you have a compromise of wide gap and hottest spark.


"Dad" > wrote in message
...
>
> "Drink" > wrote in message
> ...
> > Hi All,
> > Quick question: After modifying the ignition system, is there any
> > logical method or rule of thumb for changing the factory-recommended

spark
> > plug gap?
> > Engine in question is an '86 Corvette 350cid V8 engine with [305 heads]
> > TPI, HEI ignition, headers, high voltage coil, "performance" 8mm plug
> > wires.
> > If anyone can shed more light on the effects of the 305 V8 on the 350
> > block, I'd appreciate that as well. I think the head casting number is
> > 62426.
> > Best Regards,
> > Jim

> Any additional gap will depend on whether or not you can produce the

voltage
> required to jump the gap and still maintain a strong spark.
>
> If you think you have that available open it up a bit and try it. Not as
> good as knowing what results you will get because of the work required to
> take them out and regap. Go to some of the after market ignition sites and
> see what they recommend and at what voltage level.
> --
> Dad
> 05 C6 Silver/Red 6spd Z51
> 72 Shark Black/Black/4spd
>
>
>


  #6  
Old October 11th 04, 03:11 PM
Drink
external usenet poster
 
Posts: n/a
Default

Gents,
Just wanted to thank the both of you for your advice. Very good stuff and
much appreciated.
Best Regards,
Jim

"Tom in Missouri" > wrote in message
ink.net...
> When standard points ignitions were the norm, voltage was about 15,000 to
> 30,000, depending on who you asked. Gap was .035".
>
> When HEI began, there was 60,000 volts and the gap was .060"
>
> HEI dropped to 45,000 for reliability and the gap went to .045".
>
> See a vague pattern?
>
> If you want to check, set up one plug wire and a plug outside the engine
> where you can see it. Start the engine and let it run at various RPMs and
> see what the spark looks like. A good solid spark that is blue in color
> should give you good ignition.
>
> Shut off the engine and open the gap some. (Or set up a video camera and
> don't shut off the engine.)
>
> Do this a few times and also try closing the gap. When you find the
> strongest spark for the widest gap, go for it. The idea is that a wider
> gap
> exposes more spark and thus more initial flame to the air/fuel mixture.
> However, you need a strong spark to break through the mix and to ignite
> it.
> So you have a compromise of wide gap and hottest spark.
>
>
> "Dad" > wrote in message
> ...
>>
>> "Drink" > wrote in message
>> ...
>> > Hi All,
>> > Quick question: After modifying the ignition system, is there any
>> > logical method or rule of thumb for changing the factory-recommended

> spark
>> > plug gap?
>> > Engine in question is an '86 Corvette 350cid V8 engine with [305
>> > heads]
>> > TPI, HEI ignition, headers, high voltage coil, "performance" 8mm plug
>> > wires.
>> > If anyone can shed more light on the effects of the 305 V8 on the 350
>> > block, I'd appreciate that as well. I think the head casting number is
>> > 62426.
>> > Best Regards,
>> > Jim

>> Any additional gap will depend on whether or not you can produce the

> voltage
>> required to jump the gap and still maintain a strong spark.
>>
>> If you think you have that available open it up a bit and try it. Not as
>> good as knowing what results you will get because of the work required
>> to
>> take them out and regap. Go to some of the after market ignition sites
>> and
>> see what they recommend and at what voltage level.
>> --
>> Dad
>> 05 C6 Silver/Red 6spd Z51
>> 72 Shark Black/Black/4spd
>>
>>
>>

>



  #7  
Old October 11th 04, 03:11 PM
Drink
external usenet poster
 
Posts: n/a
Default

Gents,
Just wanted to thank the both of you for your advice. Very good stuff and
much appreciated.
Best Regards,
Jim

"Tom in Missouri" > wrote in message
ink.net...
> When standard points ignitions were the norm, voltage was about 15,000 to
> 30,000, depending on who you asked. Gap was .035".
>
> When HEI began, there was 60,000 volts and the gap was .060"
>
> HEI dropped to 45,000 for reliability and the gap went to .045".
>
> See a vague pattern?
>
> If you want to check, set up one plug wire and a plug outside the engine
> where you can see it. Start the engine and let it run at various RPMs and
> see what the spark looks like. A good solid spark that is blue in color
> should give you good ignition.
>
> Shut off the engine and open the gap some. (Or set up a video camera and
> don't shut off the engine.)
>
> Do this a few times and also try closing the gap. When you find the
> strongest spark for the widest gap, go for it. The idea is that a wider
> gap
> exposes more spark and thus more initial flame to the air/fuel mixture.
> However, you need a strong spark to break through the mix and to ignite
> it.
> So you have a compromise of wide gap and hottest spark.
>
>
> "Dad" > wrote in message
> ...
>>
>> "Drink" > wrote in message
>> ...
>> > Hi All,
>> > Quick question: After modifying the ignition system, is there any
>> > logical method or rule of thumb for changing the factory-recommended

> spark
>> > plug gap?
>> > Engine in question is an '86 Corvette 350cid V8 engine with [305
>> > heads]
>> > TPI, HEI ignition, headers, high voltage coil, "performance" 8mm plug
>> > wires.
>> > If anyone can shed more light on the effects of the 305 V8 on the 350
>> > block, I'd appreciate that as well. I think the head casting number is
>> > 62426.
>> > Best Regards,
>> > Jim

>> Any additional gap will depend on whether or not you can produce the

> voltage
>> required to jump the gap and still maintain a strong spark.
>>
>> If you think you have that available open it up a bit and try it. Not as
>> good as knowing what results you will get because of the work required
>> to
>> take them out and regap. Go to some of the after market ignition sites
>> and
>> see what they recommend and at what voltage level.
>> --
>> Dad
>> 05 C6 Silver/Red 6spd Z51
>> 72 Shark Black/Black/4spd
>>
>>
>>

>



 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
330xi Oil Pan Drain Plug - Where is it? Tom Allen BMW 4 December 31st 04 03:34 AM
1995 Audi A6 Spark Plug Torque Spec etc. Soyboy Audi 1 July 27th 04 04:19 PM


All times are GMT +1. The time now is 06:47 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.