If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
4x4 grinding noise
I have a 1991 explorer with automatic locking hubs. When I switch from 4H
to 2H, there is a very loud grinding noise when driving forward. If I disengage the hubs by backing up, then the sounds goes away. It also sometimes does it when I drive forward in 4H. I noticed it started after I was trying to gain traction on ice and I put the truck in 4H right before backing up. I am pretty sure its one of the hubs, but is there something else I should look for? I just had the 4wd motor replaced a couple months ago so it shouldn't be that. How could I check to make sure what it may be. I have also seen some postings about changing from auto to manual hubs. Is this advised? Thank you, Josh |
Ads |
#2
|
|||
|
|||
Yu can purchase the manual hubs plus the hardware kit for about the same as
what one auto hub costs...... while the auto hubs are more convenient, they are failure prone. In your case (the noise), the bad hub is trying to eat the good one. "Maida" > wrote in message lkaboutautos.com... >I have a 1991 explorer with automatic locking hubs. When I switch from 4H > to 2H, there is a very loud grinding noise when driving forward. If I > disengage the hubs by backing up, then the sounds goes away. It also > sometimes does it when I drive forward in 4H. I noticed it started after > I was trying to gain traction on ice and I put the truck in 4H right > before backing up. I am pretty sure its one of the hubs, but is there > something else I should look for? I just had the 4wd motor replaced a > couple months ago so it shouldn't be that. How could I check to make sure > what it may be. I have also seen some postings about changing from auto > to > manual hubs. Is this advised? > > Thank you, > > Josh > |
#3
|
|||
|
|||
I'll agree with Jim,,,
I replaced my auto hubs on my '94 with Warn manuals for less than the price of one automatic hub. The reliability of the Warn manual hubs far exceed the convenience of the auto's. They are very easy to install, if you can change a tire, you can install the manual hubs. btw, Merry Xmas Twano "Jim Warman" > wrote in message newsGOyd.13630$nN6.3639@edtnps84... > Yu can purchase the manual hubs plus the hardware kit for about the same as > what one auto hub costs...... while the auto hubs are more convenient, they > are failure prone. In your case (the noise), the bad hub is trying to eat > the good one. > > > "Maida" > wrote in message > lkaboutautos.com... > >I have a 1991 explorer with automatic locking hubs. When I switch from 4H > > to 2H, there is a very loud grinding noise when driving forward. If I > > disengage the hubs by backing up, then the sounds goes away. It also > > sometimes does it when I drive forward in 4H. I noticed it started after > > I was trying to gain traction on ice and I put the truck in 4H right > > before backing up. I am pretty sure its one of the hubs, but is there > > something else I should look for? I just had the 4wd motor replaced a > > couple months ago so it shouldn't be that. How could I check to make sure > > what it may be. I have also seen some postings about changing from auto > > to > > manual hubs. Is this advised? > > > > Thank you, > > > > Josh > > > > |
#4
|
|||
|
|||
the child?s breast into
cutlets, it will be indistinguishable. The taste of young human, although similar to turkey (and chicken) often can be wildly different depending upon what he or she has consumed during its 10 to 14 months of life... 4 well chosen cutlets (from the breasts of 2 healthy neonates) 2 large lemons (fresh lemons always, if possible) Olive oil Green onions Salt pepper cornstarch neonate stock (chicken, or turkey stock is fine) garlic parsley fresh cracked black pepper Season and sauté the cutlets in olive oil till golden brown, remove. Add the garlic and onions and cook down a bit. Add some lemon juice and some zest, then de-glaze with stock. Add a little cornstarch (dissolved in cold water) to the sauce. You are just about there, Pour the sauce over the cutlets, top with parsley, lemon slices and cracked pepper. Serve with spinach salad, macaroni and cheese (homemade) and iced tea... Spaghetti with Real Italian Meatballs If you don?t have an expendable bambino on hand, you can use a pound of ground pork instead. The secret to great meatballs, is to use very lean meat. 1 lb. ground flesh; human or pork 3 lb. ground beef 1 cup finely chopped onions 7 - 12 cloves garlic 1 cup seasoned bread crumbs ˝ cup milk, 2 eggs Oregano basil salt pepper Italian seasoning, etc. Tomato gravy (see index) Fresh or at least freshly cooked spaghetti or other pasta Mix the ground meats together in a large bowl, then mix each of the other ingredients. Make balls about the size of a baby?s fist (there should be one lying around for reference). Bake at 400°for about 25 minutes - or you could fry them in olive oil. Place the meatballs in the tomato gravy, and simmer for several hours. Serve on spaghetti. Accompany with green salad, garlic bread and red wine. Newborn Parmesan This classic Sicilian cuisine ca |
#5
|
|||
|
|||
I am sure the problem is with your hublocks. You will need to replace both
of them to solve your problem even if you stay with automatic hublocks. Don't worry about staying with automatic hublocks if you prefer them. The factory installed auto hublocks are also Warn hublocks and supplied to Ford. The hublocks have been improved over time and the should work for you just fine. Unfotunatly, you can only by the Warn automatic hublocks through a Ford dealership so it might cost more than buying the Warn manual hublocks through a retailer. It is very easy to replace your automatic hublocks! If you switch to the manual hublocks you will need to replace the wheel bearing retainer nut. This requires some specialty tools. This is not difficult to do and the tools are readily available. Just but be sure to consider this in the total cost of changing to manual hublocks. Happy and Safe 4x4 driving, Scott |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Steering column grinding / squeaking noise when turning right | Ed Jones | VW air cooled | 2 | January 2nd 05 10:45 AM |
1999 Cirrus making grinding noise | Bill Putney | Chrysler | 4 | October 8th 04 04:29 PM |
99 Caravan brake grinding noise even after replacing pads/disks | jogret | Dodge | 4 | October 7th 04 07:49 AM |