If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Help w/ Installng Turn Signal in GC
My daughter cracked the front pass turn signal lens on her '94 GC. I have a
new lens assy and see that it is install w/ a screw on top and screw on the bottom. I've located the screw on top but access to the bottom of the assy is a real trick. Any insight as to removing the old turn signal lens? Thx Chip L |
Ads |
#2
|
|||
|
|||
Chip L did pass the time by typing:
> My daughter cracked the front pass turn signal lens on her '94 GC. I have a > new lens assy and see that it is install w/ a screw on top and screw on the > bottom. I've located the screw on top but access to the bottom of the assy > is a real trick. > > Any insight as to removing the old turn signal lens? Thx Take the thinest phillips you have and wedge it between the upper turn signal and the lower one, about 1/2" away from the edge by the headlamp. With a flashlight you can see it better. You will push the lower signal down a bit, but that's the way it's done. When you put the new unit in, put your screwdriver on the lower screw then set the lamp in and tighen the lower screw. Then put the side one in. -- -- DougW -- 93 ZJ 4.0 http://members.cox.net/wilsond HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors Banks Header - and BEER, in the fridge! |
#3
|
|||
|
|||
Chip L did pass the time by typing:
> My daughter cracked the front pass turn signal lens on her '94 GC. I have a > new lens assy and see that it is install w/ a screw on top and screw on the > bottom. I've located the screw on top but access to the bottom of the assy > is a real trick. > > Any insight as to removing the old turn signal lens? Thx Take the thinest phillips you have and wedge it between the upper turn signal and the lower one, about 1/2" away from the edge by the headlamp. With a flashlight you can see it better. You will push the lower signal down a bit, but that's the way it's done. When you put the new unit in, put your screwdriver on the lower screw then set the lamp in and tighen the lower screw. Then put the side one in. -- -- DougW -- 93 ZJ 4.0 http://members.cox.net/wilsond HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors Banks Header - and BEER, in the fridge! |
#4
|
|||
|
|||
a long skinny phillips screw driver
Chip L wrote: > My daughter cracked the front pass turn signal lens on her '94 GC. I have a > new lens assy and see that it is install w/ a screw on top and screw on the > bottom. I've located the screw on top but access to the bottom of the assy > is a real trick. > > Any insight as to removing the old turn signal lens? Thx > > Chip L |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Turn signal | [email protected] | BMW | 2 | January 16th 05 11:04 PM |
Accord blinker turn signal relay clicking FAST when not actuated | DBarry | Honda | 1 | January 6th 05 03:04 AM |