A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Ford Explorer
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Brake upgrade for towing with a 97 Explorer



 
 
Thread Tools Display Modes
  #1  
Old March 7th 05, 12:24 AM
external usenet poster
 
Posts: n/a
Default Brake upgrade for towing with a 97 Explorer

I've been searching this group and other Explorer resources on the
Internet but I haven't found much good advice on upgrading the brakes
on my Explorer.

I have a 97 Limited, 4.0 SOHC, 4WD and I plan on pulling a trailer
cross country this summer (I'm guessing about 3,500 lbs but I'm not
sure). As far as I know most small trailers, such as UHauls, don't
have brakes so it is up to the towing vehicle to stop the trailer. I
found some Power Stop rotors at Summit Racing for $76 per front rotor,
the pads are an additional $30. Is this enough to stop an extra 2 tons
of weight? The front calipers are 2 piston calipers while the rears
are single piston. Should I sink money into high performance calipers
as well? Do I need to buy high performance rotors and pads for the
rear?

As far as the rest of the truck goes, I plan on installing a trailer
hitch, I recently flushed and filled the coolant, it has a tranny
cooler with recently flushed and filled ATF Mercon V, power steering
cooler, I'm not sure but I think the rear axle is 3.55:1. Does anyone
have any other suggestions or advice on prepping or upgrading to safely
tow a trailer?

Thanks,
Dave Earle

Ads
  #2  
Old March 7th 05, 01:11 AM
gcook
external usenet poster
 
Posts: n/a
Default

Why not check with U-haul? Many of their trailers have inertia type brakes.
Also, dashboard brake actuaters (also activated by inertia) are easy to
install. I think that would be much cheaper.
> wrote in message
ups.com...
> I've been searching this group and other Explorer resources on the
> Internet but I haven't found much good advice on upgrading the brakes
> on my Explorer.
>
> I have a 97 Limited, 4.0 SOHC, 4WD and I plan on pulling a trailer
> cross country this summer (I'm guessing about 3,500 lbs but I'm not
> sure). As far as I know most small trailers, such as UHauls, don't
> have brakes so it is up to the towing vehicle to stop the trailer. I
> found some Power Stop rotors at Summit Racing for $76 per front rotor,
> the pads are an additional $30. Is this enough to stop an extra 2 tons
> of weight? The front calipers are 2 piston calipers while the rears
> are single piston. Should I sink money into high performance calipers
> as well? Do I need to buy high performance rotors and pads for the
> rear?
>
> As far as the rest of the truck goes, I plan on installing a trailer
> hitch, I recently flushed and filled the coolant, it has a tranny
> cooler with recently flushed and filled ATF Mercon V, power steering
> cooler, I'm not sure but I think the rear axle is 3.55:1. Does anyone
> have any other suggestions or advice on prepping or upgrading to safely
> tow a trailer?
>
> Thanks,
> Dave Earle
>



  #3  
Old March 7th 05, 02:19 AM
Big Bill
external usenet poster
 
Posts: n/a
Default

On Mon, 07 Mar 2005 00:11:38 GMT, "gcook" > wrote:

>Why not check with U-haul? Many of their trailers have inertia type brakes.
>Also, dashboard brake actuaters (also activated by inertia) are easy to
>install. I think that would be much cheaper.


Of course, there have to be brakes on the trailer for those to work.
:-)
> wrote in message
oups.com...
>> I've been searching this group and other Explorer resources on the
>> Internet but I haven't found much good advice on upgrading the brakes
>> on my Explorer.
>>
>> I have a 97 Limited, 4.0 SOHC, 4WD and I plan on pulling a trailer
>> cross country this summer (I'm guessing about 3,500 lbs but I'm not
>> sure). As far as I know most small trailers, such as UHauls, don't
>> have brakes so it is up to the towing vehicle to stop the trailer. I
>> found some Power Stop rotors at Summit Racing for $76 per front rotor,
>> the pads are an additional $30. Is this enough to stop an extra 2 tons
>> of weight? The front calipers are 2 piston calipers while the rears
>> are single piston. Should I sink money into high performance calipers
>> as well? Do I need to buy high performance rotors and pads for the
>> rear?
>>
>> As far as the rest of the truck goes, I plan on installing a trailer
>> hitch, I recently flushed and filled the coolant, it has a tranny
>> cooler with recently flushed and filled ATF Mercon V, power steering
>> cooler, I'm not sure but I think the rear axle is 3.55:1. Does anyone
>> have any other suggestions or advice on prepping or upgrading to safely
>> tow a trailer?
>>
>> Thanks,
>> Dave Earle
>>

>


--
Bill Funk
Change "g" to "a"
  #4  
Old March 7th 05, 02:28 AM
Big Bill
external usenet poster
 
Posts: n/a
Default

On 6 Mar 2005 15:24:54 -0800, wrote:

>I've been searching this group and other Explorer resources on the
>Internet but I haven't found much good advice on upgrading the brakes
>on my Explorer.
>
>I have a 97 Limited, 4.0 SOHC, 4WD and I plan on pulling a trailer
>cross country this summer (I'm guessing about 3,500 lbs but I'm not
>sure). As far as I know most small trailers, such as UHauls, don't
>have brakes so it is up to the towing vehicle to stop the trailer. I
>found some Power Stop rotors at Summit Racing for $76 per front rotor,
>the pads are an additional $30. Is this enough to stop an extra 2 tons
>of weight? The front calipers are 2 piston calipers while the rears
>are single piston. Should I sink money into high performance calipers
>as well? Do I need to buy high performance rotors and pads for the
>rear?
>
>As far as the rest of the truck goes, I plan on installing a trailer
>hitch, I recently flushed and filled the coolant, it has a tranny
>cooler with recently flushed and filled ATF Mercon V, power steering
>cooler, I'm not sure but I think the rear axle is 3.55:1. Does anyone
>have any other suggestions or advice on prepping or upgrading to safely
>tow a trailer?
>
>Thanks,
>Dave Earle


I'm a freak for towing safety. So taqke this in the spirit it's
offered...
If you're going to upgrade the brakes, upgrade them as though you mean
it.
A matched system that actually increases braking over stock isn't
cheap, but it can be a life-saver. Something along the lines of a
Brembo upgrade with bigger rotor (more swept area, more braking
action, longer life, less fade) will do wonders.
If you really don't want to spend that kind of money, you could switch
to ceramic pads, for longer life, less fading.

Your Explorer will already brake hard enough to activate your
anti-lock system, so in reality, more won't do you much good, as far
as that one emergency braking maneuver is concerned. What you are
probably looking for is less fade over longer braking applications,
like going down grades. Ceramic pads should handle that nicely,
really. Just keep speeds lower where extended braking is expected, and
don't worry about the idiots who want to go faster. Remember that
downshifting (even shifting out of OD) will provide engine braking,
often (on Interstates) eliminating the need to brake at all.
Enjoy the trip!

--
Bill Funk
Change "g" to "a"
  #5  
Old March 7th 05, 03:41 AM
Ratbert
external usenet poster
 
Posts: n/a
Default

Big Bill wrote:
> On Mon, 07 Mar 2005 00:11:38 GMT, "gcook" > wrote:
>
>
>>Why not check with U-haul? Many of their trailers have inertia type brakes.
>>Also, dashboard brake actuaters (also activated by inertia) are easy to
>>install. I think that would be much cheaper.

>
>
> Of course, there have to be brakes on the trailer for those to work.
> :-)


Of course, U-haul won't rent you a trailer anyway.

  #6  
Old March 7th 05, 01:27 PM
gcook
external usenet poster
 
Posts: n/a
Default

Well, no. I meant for you to install one of the brake controllers that
throw out a large parachute. Check thr J.C.Worthless catalog. :>)
"Big Bill" > wrote in message
...
> On Mon, 07 Mar 2005 00:11:38 GMT, "gcook" > wrote:
>
> >Why not check with U-haul? Many of their trailers have inertia type

brakes.
> >Also, dashboard brake actuaters (also activated by inertia) are easy to
> >install. I think that would be much cheaper.

>
> Of course, there have to be brakes on the trailer for those to work.
> :-)
> > wrote in message
> oups.com...
> >> I've been searching this group and other Explorer resources on the
> >> Internet but I haven't found much good advice on upgrading the brakes
> >> on my Explorer.
> >>
> >> I have a 97 Limited, 4.0 SOHC, 4WD and I plan on pulling a trailer
> >> cross country this summer (I'm guessing about 3,500 lbs but I'm not
> >> sure). As far as I know most small trailers, such as UHauls, don't
> >> have brakes so it is up to the towing vehicle to stop the trailer. I
> >> found some Power Stop rotors at Summit Racing for $76 per front rotor,
> >> the pads are an additional $30. Is this enough to stop an extra 2 tons
> >> of weight? The front calipers are 2 piston calipers while the rears
> >> are single piston. Should I sink money into high performance calipers
> >> as well? Do I need to buy high performance rotors and pads for the
> >> rear?
> >>
> >> As far as the rest of the truck goes, I plan on installing a trailer
> >> hitch, I recently flushed and filled the coolant, it has a tranny
> >> cooler with recently flushed and filled ATF Mercon V, power steering
> >> cooler, I'm not sure but I think the rear axle is 3.55:1. Does anyone
> >> have any other suggestions or advice on prepping or upgrading to safely
> >> tow a trailer?
> >>
> >> Thanks,
> >> Dave Earle
> >>

> >

>
> --
> Bill Funk
> Change "g" to "a"



  #7  
Old March 17th 05, 05:19 AM
Barry
external usenet poster
 
Posts: n/a
Default

I have had no problems towing an 18 ft car hauler w/ my 91 Exploder which
has the towing package & no brake upgrades.
It stops very well in tandem w/ the elec trailer brakes. Towing a loaded car
hauler up hill is another matter, as is the fuel consumption.
"Big Bill" > wrote in message
...
> On 6 Mar 2005 15:24:54 -0800, wrote:
>
> >I've been searching this group and other Explorer resources on the
> >Internet but I haven't found much good advice on upgrading the brakes
> >on my Explorer.
> >
> >I have a 97 Limited, 4.0 SOHC, 4WD and I plan on pulling a trailer
> >cross country this summer (I'm guessing about 3,500 lbs but I'm not
> >sure). As far as I know most small trailers, such as UHauls, don't
> >have brakes so it is up to the towing vehicle to stop the trailer. I
> >found some Power Stop rotors at Summit Racing for $76 per front rotor,
> >the pads are an additional $30. Is this enough to stop an extra 2 tons
> >of weight? The front calipers are 2 piston calipers while the rears
> >are single piston. Should I sink money into high performance calipers
> >as well? Do I need to buy high performance rotors and pads for the
> >rear?
> >
> >As far as the rest of the truck goes, I plan on installing a trailer
> >hitch, I recently flushed and filled the coolant, it has a tranny
> >cooler with recently flushed and filled ATF Mercon V, power steering
> >cooler, I'm not sure but I think the rear axle is 3.55:1. Does anyone
> >have any other suggestions or advice on prepping or upgrading to safely
> >tow a trailer?
> >
> >Thanks,
> >Dave Earle

>
> I'm a freak for towing safety. So taqke this in the spirit it's
> offered...
> If you're going to upgrade the brakes, upgrade them as though you mean
> it.
> A matched system that actually increases braking over stock isn't
> cheap, but it can be a life-saver. Something along the lines of a
> Brembo upgrade with bigger rotor (more swept area, more braking
> action, longer life, less fade) will do wonders.
> If you really don't want to spend that kind of money, you could switch
> to ceramic pads, for longer life, less fading.
>
> Your Explorer will already brake hard enough to activate your
> anti-lock system, so in reality, more won't do you much good, as far
> as that one emergency braking maneuver is concerned. What you are
> probably looking for is less fade over longer braking applications,
> like going down grades. Ceramic pads should handle that nicely,
> really. Just keep speeds lower where extended braking is expected, and
> don't worry about the idiots who want to go faster. Remember that
> downshifting (even shifting out of OD) will provide engine braking,
> often (on Interstates) eliminating the need to brake at all.
> Enjoy the trip!
>
> --
> Bill Funk
> Change "g" to "a"



 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Brake rotors already grooving [email protected] Technology 46 January 15th 05 04:42 PM
HELP! - 2002 Explorer Rear Brake Caliper Sticking discgolfer7213 Ford Explorer 0 January 11th 05 03:16 AM
How to replace brake lines on 1976 Rabbit? Joseph Meehan VW water cooled 10 January 2nd 05 04:21 AM
'66 Brake Upgrade .boB Ford Mustang 1 December 21st 04 07:29 PM
civic big brake upgrade - pt II jim beam Honda 0 October 16th 04 03:25 PM


All times are GMT +1. The time now is 01:12 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.