If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Steering wheel lock plate
I need to remove the lock plate on my 92 cherokee to replace the turn
signal/ dimmer switch but cant get the lock plate off. I would cut the retaining clip if I knew I didnt need to put it back on. Its just an old fishing car I use to pull my boat down to the lake so Im not worried if the steering wheel doesnt lock.. YEs Ive seen the tools for doing it and dont want to pay the money if I dont have to. Thanks Jimmie |
Ads |
#2
|
|||
|
|||
Steering wheel lock plate
Our local auto parts stores will lend the tool out.
You might need two people to manually take it off if you are small. I can lean onto the plate with one hand and pop the clip out with a screwdriver and the other hand. I weigh about 210 though... You might need two hands to bend the plate down... Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) Jimmie D wrote: > I need to remove the lock plate on my 92 cherokee to replace the turn > signal/ dimmer switch but cant get the lock plate off. > I would cut the retaining clip if I knew I didnt need to put it back on. Its > just an old fishing car I use to pull my boat down to the lake so Im not > worried if the steering wheel doesnt lock.. YEs Ive seen the tools for doing > it and dont want to pay the money if I dont have to. > > Thanks Jimmie > > |
#3
|
|||
|
|||
Steering wheel lock plate
DO NOT cut the retaining clip.
There is a Lock Ring Removal Tool that costs less than $10. It's kind of an elongated U shape with a long bolt up the middle. As you turn the bolt, the legs of the U push the locking plate down the steering column shaft. You can then remove the snap ring and release the tool, the lock ring slides right off after that. An autoparts store that has a Loaner Tool Program will let you take the tool home to use, then bring it back. It's almost the same as checking a book out of the library, except you learn stuff and get dirty at the same time. "Jimmie D" > wrote in message ... >I need to remove the lock plate on my 92 cherokee to replace the turn >signal/ dimmer switch but cant get the lock plate off. > I would cut the retaining clip if I knew I didnt need to put it back on. > Its just an old fishing car I use to pull my boat down to the lake so Im > not worried if the steering wheel doesnt lock.. YEs Ive seen the tools for > doing it and dont want to pay the money if I dont have to. > > Thanks Jimmie > |
#4
|
|||
|
|||
Steering wheel lock plate
Easy. Using two hands, push down evenly on both sides of the plate. Push very hard and hold it down. With your third hand, pull outward gently on the steering shaft. With your fourth and fifth hands, pry the clip loose with small screwdrivers or picks and slide it off the shaft. Gently release the plate with hands 1 and 2. -rev On Jan 25, 1:58 pm, "Jimmie D" > wrote: > I need to remove the lock plate on my 92 cherokee to replace the turn > signal/ dimmer switch but cant get the lock plate off. > I would cut the retaining clip if I knew I didnt need to put it back on. Its > just an old fishing car I use to pull my boat down to the lake so Im not > worried if the steering wheel doesnt lock.. YEs Ive seen the tools for doing > it and dont want to pay the money if I dont have to. > > Thanks Jimmie |
#5
|
|||
|
|||
Steering wheel lock plate
ok, what would happen if I cut the ring, nobdy around has the tool. I
believe you when you say I shouldnt do it but still I am curious. Also are the retainer rings available at the local parts store/ jeep dealer should it go flying off into the bermuda grass. JImmie On Jan 25, 3:37 pm, "Jeff Strickland" > wrote: > DO NOT cut the retaining clip. > > There is a Lock Ring Removal Tool that costs less than $10. It's kind of an > elongated U shape with a long bolt up the middle. As you turn the bolt, the > legs of the U push the locking plate down the steering column shaft. You can > then remove the snap ring and release the tool, the lock ring slides right > off after that. > > An autoparts store that has a Loaner Tool Program will let you take the tool > home to use, then bring it back. It's almost the same as checking a book out > of the library, except you learn stuff and get dirty at the same time. > > "Jimmie D" > wrote in .net... > > > > >I need to remove the lock plate on my 92 cherokee to replace the turn > >signal/ dimmer switch but cant get the lock plate off. > > I would cut the retaining clip if I knew I didnt need to put it back on. > > Its just an old fishing car I use to pull my boat down to the lake so Im > > not worried if the steering wheel doesnt lock.. YEs Ive seen the tools for > > doing it and dont want to pay the money if I dont have to. > > > Thanks Jimmie- Hide quoted text -- Show quoted text - |
#6
|
|||
|
|||
Steering wheel lock plate
It's a standard GM Steering Wheel Lock Ring Removal Tool. The tool is as
common as electricity and water. I think you can take the ring out without the tool, as another poster suggested. Use two hands to hold the lock ring down, use your third and fourth hands to remove the clip, the lock ring can then be lifted off. The lock ring is held against the clip by a VERY strong spring. I haven't tried very hard, but I think the clip is next to impossible to get off without the removal tool. Mike Romain seems to think the clip can be removed, but my experience was not the same. I had to go buy the tool because I could not hold the ring down and pry the clip out at the same time. Here's a link to an eBay auction http://cgi.ebay.com/ebaymotors/Steer...spagenameZWDVW There are more listings using the search, STEERING WHEEL LOCK RING REMOVAL TOOL There are different configurations of essentially the same tool. On my CJ5, I bought the GM Type of tool. It looks similar to the picture in the link, but is narrower -- mine is about 2.5 inches wide, the picture looks to be more like 5 inches to me. I understand that you might not want to buy on eBay, but finding the product you need might help you get it locally. AutoZone has the tool, and they will let you use it for free. > wrote in message oups.com... > ok, what would happen if I cut the ring, nobdy around has the tool. I > believe you when you say I shouldnt do it but still I am curious. Also > are the retainer rings available at the local parts store/ jeep dealer > should it go flying off into the bermuda grass. > > JImmie > > On Jan 25, 3:37 pm, "Jeff Strickland" > wrote: >> DO NOT cut the retaining clip. >> >> There is a Lock Ring Removal Tool that costs less than $10. It's kind of >> an >> elongated U shape with a long bolt up the middle. As you turn the bolt, >> the >> legs of the U push the locking plate down the steering column shaft. You >> can >> then remove the snap ring and release the tool, the lock ring slides >> right >> off after that. >> >> An autoparts store that has a Loaner Tool Program will let you take the >> tool >> home to use, then bring it back. It's almost the same as checking a book >> out >> of the library, except you learn stuff and get dirty at the same time. >> >> "Jimmie D" > wrote in >> .net... >> >> >> >> >I need to remove the lock plate on my 92 cherokee to replace the turn >> >signal/ dimmer switch but cant get the lock plate off. >> > I would cut the retaining clip if I knew I didnt need to put it back >> > on. >> > Its just an old fishing car I use to pull my boat down to the lake so >> > Im >> > not worried if the steering wheel doesnt lock.. YEs Ive seen the tools >> > for >> > doing it and dont want to pay the money if I dont have to. >> >> > Thanks Jimmie- Hide quoted text -- Show quoted text - > |
#7
|
|||
|
|||
Steering wheel lock plate
http://www.chevyasylum.com/column/tiltcol.html
http://www.nastyz28.com/tech/e-tiltcol.html http://www.fieros.de/en/articles/steering.html God Bless America, Bill 0|||||||0 http://www.billhughes.com/ "Jimmie D" > wrote in message ... > I need to remove the lock plate on my 92 cherokee to replace the turn > signal/ dimmer switch but cant get the lock plate off. > I would cut the retaining clip if I knew I didnt need to put it back on. Its > just an old fishing car I use to pull my boat down to the lake so Im not > worried if the steering wheel doesnt lock.. YEs Ive seen the tools for doing > it and dont want to pay the money if I dont have to. > > Thanks Jimmie > > |
#8
|
|||
|
|||
Steering wheel lock plate
Replace the solenoid, it is very common for them to weld together
especially with the high amperage draw with a bad starter, and a low battery. God Bless America, Bill 0|||||||0 http://www.billhughes.com/ "Jimmie D" > wrote in message ... > I need to remove the lock plate on my 92 cherokee to replace the turn > signal/ dimmer switch but cant get the lock plate off. > I would cut the retaining clip if I knew I didnt need to put it back on. Its > just an old fishing car I use to pull my boat down to the lake so Im not > worried if the steering wheel doesnt lock.. YEs Ive seen the tools for doing > it and dont want to pay the money if I dont have to. > > Thanks Jimmie > > |
#9
|
|||
|
|||
Steering wheel lock plate
Thanks Bill, You are THE MAN. WIfe went back to auto zone and she
managed to talk to someone who had a clue and they did have the tool after all. Also my steering column is a little wobbly, I hadnt planned on doing anything about it just yet but with the info you supplied I will get er done this weekend. Thanks all Jimmie PS 264000 miles, I will be very happy if she sees 300K. On Jan 25, 7:02 pm, "L.W. \(Bill\) Hughes III" > wrote: > Replace the solenoid, it is very common for them to weld together > especially with the high amperage draw with a bad starter, and a low > battery. > God Bless America, Bill 0|||||||0 > / > > "Jimmie D" > wrote in .net... > > > > > I need to remove the lock plate on my 92 cherokee to replace the turn > > signal/ dimmer switch but cant get the lock plate off. > > I would cut the retaining clip if I knew I didnt need to put it back on. > Its > > just an old fishing car I use to pull my boat down to the lake so Im not > > worried if the steering wheel doesnt lock.. YEs Ive seen the tools for > doing > > it and dont want to pay the money if I dont have to. > > > Thanks Jimmie- Hide quoted text -- Show quoted text - |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Cruise Control Steering Wheel Switch Replacement - '96 Explorer | Len Krauss | Ford Explorer | 1 | August 23rd 06 04:30 AM |
Impala steering will not lock, key will not turn | kbee | Technology | 2 | July 9th 06 05:44 AM |
why a tight steering wheel? | [email protected] | Chrysler | 5 | June 18th 06 03:37 AM |
91 Golf Needs Adjustable Left Tie Rod | you are nuts | VW water cooled | 7 | December 21st 05 07:30 PM |
Honda Civic VTI steering wheel | colenum | Honda | 0 | April 9th 05 01:36 PM |