If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
E30 OBC Question
I have it somewhere, but WHERE is the question... How do I reset my
OBC to English and set the time/date? |
Ads |
#2
|
|||
|
|||
Psycho wrote: > I have it somewhere, but WHERE is the question... How do I reset my > OBC to English and set the time/date? RTFM. -- C.R. Krieger (Been there; done that) |
#3
|
|||
|
|||
"C.R. Krieger" > wrote in message oups.com... > > Psycho wrote: > > I have it somewhere, but WHERE is the question... How do I reset my > > OBC to English and set the time/date? > > RTFM. CR, The manual explains how to set the clock and the calendar, but is silent on the language. That is, I think it's silent on changing the language. |
#4
|
|||
|
|||
Thanks for the reply but do you think I'd be asking if I had the
FSUCKING manual? Sure isn't as friendly here as it was 7 months ago... On 8 Mar 2005 12:19:45 -0800, "C.R. Krieger" > wrote: > >Psycho wrote: >> I have it somewhere, but WHERE is the question... How do I reset my >> OBC to English and set the time/date? > >RTFM. |
#5
|
|||
|
|||
Setting the Clock and the Date is as simple as holding the respective button
until the message says INPUT TIME or INPUT DATE, then use the 1000, 100,10, and 1 buttons to input the new data. The trouble is getting the display to read in English. It is just a matter of holding some buttons while switching the ignition to ON, but not START. I don't recall which buttons need to be held. .. "Psycho" > wrote in message ... > Thanks for the reply but do you think I'd be asking if I had the > FSUCKING manual? Sure isn't as friendly here as it was 7 months ago... > > On 8 Mar 2005 12:19:45 -0800, "C.R. Krieger" > > wrote: > > > > >Psycho wrote: > >> I have it somewhere, but WHERE is the question... How do I reset my > >> OBC to English and set the time/date? > > > >RTFM. > |
#6
|
|||
|
|||
Thanks Jeff, I did manage to find the information on one of the
unofficial BMW sites. OBC now reads correctly (to me at least). Now I just need to get the correct coding plug for it. The one in it now is from a 535. Not good for the range function or MPG... On Wed, 9 Mar 2005 13:09:31 -0800, "Jeff Strickland" > wrote: >Setting the Clock and the Date is as simple as holding the respective button >until the message says INPUT TIME or INPUT DATE, then use the 1000, 100,10, >and 1 buttons to input the new data. The trouble is getting the display to >read in English. It is just a matter of holding some buttons while switching >the ignition to ON, but not START. I don't recall which buttons need to be >held. > >. > > >"Psycho" > wrote in message .. . >> Thanks for the reply but do you think I'd be asking if I had the >> FSUCKING manual? Sure isn't as friendly here as it was 7 months ago... >> >> On 8 Mar 2005 12:19:45 -0800, "C.R. Krieger" > >> wrote: >> >> > >> >Psycho wrote: >> >> I have it somewhere, but WHERE is the question... How do I reset my >> >> OBC to English and set the time/date? >> > >> >RTFM. >> > |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
League Set-Up Question??? | TlgtrProd | Simulators | 0 | January 23rd 05 04:44 PM |
Where to get Official Speed Limit Info | [email protected] | Driving | 40 | January 3rd 05 07:10 AM |
009 Distributor question | [email protected] | VW air cooled | 5 | December 31st 04 09:52 AM |
JEEP question - 4.0 vs 4.0HO | James Morrow | 4x4 | 12 | June 2nd 04 05:16 PM |