If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
degreasing old tools
I have what were my grandfather's tools. A mix of snap on, SK, craftsman, various cheapos, other brands that look like quality tools but the names I haven't seen anywhere else. Anyway almost all of them are coated in grease and dirt from many years of use without cleaning. The sockets have grease and dirt caked inside. As I go through cleaning them, each one seems dirtier than the next. It is taking far too long to clean them. Anyone know of any good cleaners/degreasers that would work well in getting them clean? Something I can just soak them in that would at least take most of the grime off? thanks |
Ads |
#2
|
|||
|
|||
Brent P wrote:
> I have what were my grandfather's tools. A mix of snap on, SK, craftsman, > various cheapos, other brands that look like quality tools but the names > I haven't seen anywhere else. Anyway almost all of them are coated in > grease and dirt from many years of use without cleaning. The sockets > have grease and dirt caked inside. As I go through cleaning them, each > one seems dirtier than the next. It is taking far too long to clean them. > > Anyone know of any good cleaners/degreasers that would work well in > getting them clean? Something I can just soak them in that would at least > take most of the grime off? > > thanks The eco-weenies will go nuts, but kerosene works well and as a bonus leaves a little protective wax coating on them. For the REALLY dirty tools, Berkebile 2+2 carb cleaner is the all purpose, cleans-everything solvent. Don't spray it anywhere near paint! It'll eat plastic screwdriver handles as well. If that doesn't work, a bucket of carb dip is the ticket, but it'll eat anything that's not 100% metal. good luck nate -- replace "fly" with "com" to reply. http://home.comcast.net/~njnagel |
#3
|
|||
|
|||
"Brent P" > wrote in message ... > > I have what were my grandfather's tools. A mix of snap on, SK, craftsman, > various cheapos, other brands that look like quality tools but the names > I haven't seen anywhere else. Anyway almost all of them are coated in > grease and dirt from many years of use without cleaning. The sockets > have grease and dirt caked inside. As I go through cleaning them, each > one seems dirtier than the next. It is taking far too long to clean them. > > Anyone know of any good cleaners/degreasers that would work well in > getting them clean? Something I can just soak them in that would at least > take most of the grime off? > > thanks > > > Tried a bucket of gasoline & a parts cleaning brush, VERY CAREFULLY? If u feel u need a solvent, buy some Gunk engine de-greaser. Got a GOOD friend with a solvent tank--may not be friends afterwards, but it'll clean nicely! Lacquer thinner, cheapest available, works well. (If any of these suggestions don't suffice, how much for the tools, grease included?) s |
#4
|
|||
|
|||
> Anyone know of any good cleaners/degreasers that would work well in > getting them clean? Something I can just soak them in that would at > least take most of the grime off? You might see if a local service station will let you use their parts cleaner for a reasonable price. |
#5
|
|||
|
|||
Run 'em through the dishwasher. |
#6
|
|||
|
|||
Daniel J. Stern wrote:
> Run 'em through the dishwasher. > You're single, aren't you? nate (tried that with some old hubcaps once...) -- replace "fly" with "com" to reply. http://home.comcast.net/~njnagel |
#7
|
|||
|
|||
"Nate Nagel" > wrote in message ... > Daniel J. Stern wrote: > > > Run 'em through the dishwasher. > > > > You're single, aren't you? > > nate > > (tried that with some old hubcaps once...) Bet you're single after that!!! s |
#8
|
|||
|
|||
In article ich.edu>, Daniel J. Stern wrote:
> > Run 'em through the dishwasher. I like my dishwasher. But the thought did cross my mind. |
#9
|
|||
|
|||
Try a good overnight soak in something like Simple Green and then put
on your rubber gloves and safety glasses and have at 'em with a retired toothbrush. >> dishwasher > You're single, aren't you? Putting Grampa's socket wrenches in an ultrasonic jewelry cleaner is probably the gold standard in being single, or becoming so. Actually the dishwasher isn't that bad an idea (NOT after using petrochemical cleaners, please), but you'll have to rescue them immediately for an oil bath or you'll see rust a-plenty. : other brands that look like quality tools but the names : I haven't seen anywhere else. There have been some good brands come and go. I'm still using a few hand tools from Diamond Calk Horseshoe Co. after my dad put them through a half century of break-in, for instance. Lots of memories of being taught not only how but why to do things right, there. The years have also seen a lot of junk brands come and go. Hey, that way you get to stock a tool roll for each car without raiding your working supply. Cheers, --Joe |
#10
|
|||
|
|||
In article .com>, Ad absurdum per aspera wrote:
> Try a good overnight soak in something like Simple Green and then put > on your rubber gloves and safety glasses and have at 'em with a retired > toothbrush. That's what I've been doing. SLOW process. It's taking a couple days of soaking and repeated brushing and finishing off with chrome cleaner. It does work, it just takes too long. thanks for the suggestions. I may go get some kerosene. I tried the only carb cleaner I have on hand (just regular ol' gumout), seems to do as well as the simple green but faster. Will know after the socket soaks in there for some time longer. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
degreasing old tools | Brent P | Driving | 34 | March 2nd 05 05:31 AM |
What brand of tools favored by pros? | Roger Sircar | Chrysler | 11 | November 15th 04 03:50 PM |
Audi Special tools | ~ ElektraMan ~ | Audi | 4 | November 3rd 04 09:33 PM |
EXCESS TOOL INVENTORY- SPX/OTC-SERVICE SOLUTIONS TOOLS | Kirk Rocheford-All World, Inc. | Dodge | 0 | October 18th 04 05:37 PM |