A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto newsgroups » General
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Car Brake Pads Installed Incorrectly



 
 
Thread Tools Display Modes
  #1  
Old August 11th 04, 12:27 PM
eddy eagle
external usenet poster
 
Posts: n/a
Default Car Brake Pads Installed Incorrectly

(CE) wrote in message . com>...
> Hello,
>
> I took my car, 98 Civic to a local store for brake pads to be changed.
> After regular driving of 12,000 miles after the change, there was
> sqeaking/metal scratching noise, and I took it back to the shop to
> have them check it out. They told me the caliper was sticking and was
> not releasing correctly.
>
> I then found out that my Honda Warranty covers a faulty caliper, and I
> take it back a honda dealer to have the caliper replaced. I told them
> my story with the previous shop that did the brake pads, and they ran
> a diagnostics. They told me my calipers were fine, and the problem was
> brake pads were installed incorrectly (the inner and outer pads were
> reversed), and combined with A/M brake pads that were very inferior,
> the pads wore down quickly, and causing the sensor to scratch on the
> rotor.
>
> Honda then told me they recommended new brake pads and possibly new
> rotors.
>
> My question is:
> 1. Can the car brake pads be installed incorrectly ( They looked like
> they were symmetrical enough to not make a difference whether the
> inner pad and outer pad was reversed and admittedly, i have untrained
> eyes to judge).
>
> 2. One other thing I noted: The brake pad that wore down, wasn't even
> in thickness, even though it was thinning out in thickness, it was at
> an angle.. so what i think is the front end of the pad was thinner
> than the back end of the pad.
>
> 3. If the caliper was sticking on both sides, .. shouldn't the pads,
> both inner and outer be worn down to a very thin level, but even in
> thickness throughout the pad ?
>
> 4. And if the caliper was sticking on one side, .. shouldn't the side
> thats bad(sticking) cause the pad to be really worn down, but at a
> even level ? instead of an angle ?
>
> I was also thinking the only way I could really tell if the caliper
> was bad, .. would be to drive it another 12000 miles, and see if the
> pads were thinned out again, at a slanted angle, like before, .. and I
> am sure someone out there would be able to gauge as to whats likely
> and whats not.
>
> I've gone through a lot of the postings on this group, and found one
> posting to ask if its possible to have pads backwards ( he sounded
> like it was an impossible thing to do), and also 2 postings that
> suggested that could be a problem for other postings...so there seems
> to be mixed consensus about pads being installed incorrectly
>
> Any brake experts out there for civic 98 car ?


It is possible for cheap pads to wear out in 12,000 miles.
Pads usually wear more on the inner one than the outer one.
The leading edge of the pad can wear more causing some of the
unevenness you observed. Installation and other hardware issues can
also increase the wear and unevenness. Perhaps the wheel bearings were
loose also.
The proof in the pudding is that your cheap brake job only lasted
12,000 miles. Now find a decent shop and get it fixed.
Ads
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
brake pads for 2001 Audi A4 2.8L V6 Quattro Curtis Newton Audi 2 November 18th 04 03:44 PM
Nice page about 'bedding' brake pads Chopface Honda 1 November 10th 04 02:50 PM
Brake Noise Caused by Cheap Brake Pads? Jay Bollyn Saturn 2 October 30th 04 11:19 PM


All times are GMT +1. The time now is 04:32 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.