If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Exhaust help
I decided to do a good deed and change the rusted center pipe on my inlaws 88
Accord. Of course this is turning into a bigger job than expexted. I finally got pipe out but cutting and grinding the bolts that held the pipe to the cat convertor. I thought I could just push the bolts out, but apparently not. Any tips on getting these bolts out? ---------------- Alex |
Ads |
#2
|
|||
|
|||
Alex Rodriguez wrote:
> I decided to do a good deed and change the rusted center pipe on my inlaws 88 > Accord. Of course this is turning into a bigger job than expexted. I finally > got pipe out but cutting and grinding the bolts that held the pipe to the cat > convertor. I thought I could just push the bolts out, but apparently not. Any > tips on getting these bolts out? > ---------------- > Alex > the bolts are captive & come with the pipe. oem pipe anyway. if you can seperate the pipe from the converter, you should be in business for replacement. |
#3
|
|||
|
|||
jim beam wrote:
> Alex Rodriguez wrote: > >> I decided to do a good deed and change the rusted center pipe on my >> inlaws 88 Accord. Of course this is turning into a bigger job than >> expexted. I finally got pipe out but cutting and grinding the bolts >> that held the pipe to the cat convertor. I thought I could just push >> the bolts out, but apparently not. Any tips on getting these bolts out? >> ---------------- >> Alex >> > the bolts are captive & come with the pipe. oem pipe anyway. if you > can seperate the pipe from the converter, you should be in business for > replacement. > The bolts between converter and center pipe (Pipe B) are actually separate, and are called "converter bolts". On my 94 Civic these are specialty bolts (not cheap, same for the 88 Accord) that have a thin, flat head and "ridged" spine designed to grip in the holes in the converter and help prevent the bolt from turning as you apply the nut. I tried to get mine out but found that the rust was more than I could handle with my equipment. Mechanic charged me $75 to do it. Maybe try heat and hammering them out with a punch from the Pipe B side? Just be careful not to pound so hard that you damage either the cat or Pipe A, both of which cost a lot. Might be better to drill them out. |
#4
|
|||
|
|||
I used a 5" angle grinder (wear a full cover face mask when doing this)
and cut them off both ends of the cat - both nut end and bolt end. Removed the pipes and cat and drilled out the bolts in the cat and replaced them with new bolts. Be careful with the cat sensor - it will disconnect. |
#5
|
|||
|
|||
|
#6
|
|||
|
|||
In article >, says...
>The bolts between converter and center pipe (Pipe B) are actually >separate, and are called "converter bolts". On my 94 Civic these are >specialty bolts (not cheap, same for the 88 Accord) that have a thin, >flat head and "ridged" spine designed to grip in the holes in the >converter and help prevent the bolt from turning as you apply the nut. > >I tried to get mine out but found that the rust was more than I could >handle with my equipment. Mechanic charged me $75 to do it. Maybe try >heat and hammering them out with a punch from the Pipe B side? Just be >careful not to pound so hard that you damage either the cat or Pipe A, >both of which cost a lot. Might be better to drill them out. Thanks for the tip. I tried pounding on the bolts with a hammer, not a big one, and they bolts would not budge. I tried drilling them out, but my drill bits were not up to the task. I'm going to buy a couple of decent bits before I try again this weekend. Since I am going to drill them out, I'm not going to bother with the special bolts. ---------------- Alex |
#7
|
|||
|
|||
Alex Rodriguez wrote:
> In article >, says... > > >>The bolts between converter and center pipe (Pipe B) are actually >>separate, and are called "converter bolts". On my 94 Civic these are >>specialty bolts (not cheap, same for the 88 Accord) that have a thin, >>flat head and "ridged" spine designed to grip in the holes in the >>converter and help prevent the bolt from turning as you apply the nut. >> >>I tried to get mine out but found that the rust was more than I could >>handle with my equipment. Mechanic charged me $75 to do it. Maybe try >>heat and hammering them out with a punch from the Pipe B side? Just be >>careful not to pound so hard that you damage either the cat or Pipe A, >>both of which cost a lot. Might be better to drill them out. > > > Thanks for the tip. I tried pounding on the bolts with a hammer, not a big > one, and they bolts would not budge. I tried drilling them out, but my drill > bits were not up to the task. I'm going to buy a couple of decent bits before > I try again this weekend. Since I am going to drill them out, I'm not going to > bother with the special bolts. > ---------------- > Alex > > ordinary bolts will soften & creep at high temperature. and the exit of the cat is /very/ high temperature! |
#8
|
|||
|
|||
"jim beam" > wrote in message ... > Alex Rodriguez wrote: > ordinary bolts will soften & creep at high temperature. and the exit of > the cat is /very/ high temperature! What is the difference between ordinary bolts and the ones you refer to, Jim? |
#9
|
|||
|
|||
|
#10
|
|||
|
|||
SoCalMike wrote:
> wrote: > >> "jim beam" > wrote in message >> ... >> >>> Alex Rodriguez wrote: >> >> >> >>> ordinary bolts will soften & creep at high temperature. and the exit of >>> the cat is /very/ high temperature! >> >> >> >> What is the difference between ordinary bolts and the ones you refer to, >> Jim? >> >> > the OEM bolts are splined to stay snug in the hole. right? Ahh, is THAT what it's called. Yes, they are splined. The shop that got the old ones out for me was apparently able to get them out without making the holes too big to grip the spline--I'd be careful about that if you're drilling them out. Pretty heavy-duty little suckers, too--though short, they weigh several ounces at least (3 of 'em, anyway). No wonder they were some $7 each. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Fix-it exhaust ticket in Virginia? | N8N | Driving | 9 | July 12th 05 10:09 PM |
Questions about Repairing My Exhaust | Julie P. | Technology | 12 | April 7th 05 09:54 PM |
Opinions Wanted: 66 Exhaust Setup | Scott | Ford Mustang | 2 | March 11th 05 12:36 AM |
85 Chevy Caprice. Restricted Exhaust ? | [email protected] | Technology | 14 | February 20th 05 06:46 PM |
Lifetime exhaust warranty ? | DriveSpy | VW water cooled | 7 | February 4th 05 12:00 AM |