If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Clearing out A/C condenser drain holes
I believe the drain holes where condensate from my air conditioner drains
are plugged up. I don't see any water dripping on the ground when I run the A/C and I get a faint smell of mildew when I first start up the fan. Unfortunately, my Chilton's manual doesn't show where these holes are or how to clear them out. Can anyone give me some pointers and/or point me to a diagram on the internet? Thanks in advance. |
Ads |
#2
|
|||
|
|||
I had a musty smell awhile back and fixed it without any disassemble or
work. Try this first: Close all the vents on the for the AC. Put the Fan on full. With the vents closed, the back pressure of the air may very well blow the drains clear. I also poured some bleach down there to kill the mold and muck. "MPost" > wrote in message ... >I believe the drain holes where condensate from my air conditioner drains >are plugged up. I don't see any water dripping on the ground when I run the >A/C and I get a faint smell of mildew when I first start up the fan. >Unfortunately, my Chilton's manual doesn't show where these holes are or >how to clear them out. Can anyone give me some pointers and/or point me to >a diagram on the internet? > > Thanks in advance. > |
#3
|
|||
|
|||
Oh yes, I also believe you need it on reticulate.
"Mikus" > wrote in message .. . >I had a musty smell awhile back and fixed it without any disassemble or >work. > > Try this first: > > Close all the vents on the for the AC. > Put the Fan on full. > With the vents closed, the back pressure of the air may very well blow the > drains clear. > > I also poured some bleach down there to kill the mold and muck. > > "MPost" > wrote in message > ... >>I believe the drain holes where condensate from my air conditioner drains >>are plugged up. I don't see any water dripping on the ground when I run >>the A/C and I get a faint smell of mildew when I first start up the fan. >>Unfortunately, my Chilton's manual doesn't show where these holes are or >>how to clear them out. Can anyone give me some pointers and/or point me to >>a diagram on the internet? >> >> Thanks in advance. >> > > |
#4
|
|||
|
|||
Bleach is a bad idea. Residue may damage coils. Lysol spray is better
choice or purchase foam designed for the purpose from car dealership. I am surprised that back pressure could clear it. "Mikus" > wrote in message .. . >I had a musty smell awhile back and fixed it without any disassemble or >work. > > Try this first: > > Close all the vents on the for the AC. > Put the Fan on full. > With the vents closed, the back pressure of the air may very well blow the > drains clear. > > I also poured some bleach down there to kill the mold and muck. > > "MPost" > wrote in message > ... >>I believe the drain holes where condensate from my air conditioner drains >>are plugged up. I don't see any water dripping on the ground when I run >>the A/C and I get a faint smell of mildew when I first start up the fan. >>Unfortunately, my Chilton's manual doesn't show where these holes are or >>how to clear them out. Can anyone give me some pointers and/or point me to >>a diagram on the internet? >> >> Thanks in advance. >> > > |
#5
|
|||
|
|||
Art wrote:
> Bleach is a bad idea. Residue may damage coils. Lysol spray is better > choice or purchase foam designed for the purpose from car dealership. I am > surprised that back pressure could clear it. > > > "Mikus" > wrote in message > .. . > >>I had a musty smell awhile back and fixed it without any disassemble or >>work. >> >>Try this first: >> >>Close all the vents on the for the AC. >>Put the Fan on full. >>With the vents closed, the back pressure of the air may very well blow the >>drains clear. >> >>I also poured some bleach down there to kill the mold and muck. >> >>"MPost" > wrote in message ... >> >>>I believe the drain holes where condensate from my air conditioner drains >>>are plugged up. I don't see any water dripping on the ground when I run >>>the A/C and I get a faint smell of mildew when I first start up the fan. >>>Unfortunately, my Chilton's manual doesn't show where these holes are or >>>how to clear them out. Can anyone give me some pointers and/or point me to >>>a diagram on the internet? >>> >>>Thanks in advance. >>> >> >> > > I'd be worried about using bleach, especially when your drains are clogged, unless you enjoy the smell of bleach There are commercial products made specifically for this, you dump it down the vent intake in front of your windshield. As for locating the drains, can't help you there.... -- They that can give up essential liberty to obtain a little temporary safety deserve neither liberty nor safety. Benjamin Franklin |
#6
|
|||
|
|||
Interesting idea. I tried the back pressure technique, but unfortunately, it
didn't work for me. Any other ideas on how to locate and clear the drain holes? "Mikus" > wrote in message . .. > Oh yes, I also believe you need it on reticulate. > > > "Mikus" > wrote in message > .. . >>I had a musty smell awhile back and fixed it without any disassemble or >>work. >> >> Try this first: >> >> Close all the vents on the for the AC. >> Put the Fan on full. >> With the vents closed, the back pressure of the air may very well blow >> the drains clear. >> >> I also poured some bleach down there to kill the mold and muck. >> >> "MPost" > wrote in message >> ... >>>I believe the drain holes where condensate from my air conditioner drains >>>are plugged up. I don't see any water dripping on the ground when I run >>>the A/C and I get a faint smell of mildew when I first start up the fan. >>>Unfortunately, my Chilton's manual doesn't show where these holes are or >>>how to clear them out. Can anyone give me some pointers and/or point me >>>to a diagram on the internet? >>> >>> Thanks in advance. >>> >> >> > > |
#7
|
|||
|
|||
MPost wrote:
> Interesting idea. I tried the back pressure technique, but unfortunately, it > didn't work for me. Any other ideas on how to locate and clear the drain > holes? > > "Mikus" > wrote in message > . .. > >>Oh yes, I also believe you need it on reticulate. >> >> >>"Mikus" > wrote in message ... >> >>>I had a musty smell awhile back and fixed it without any disassemble or >>>work. >>> >>>Try this first: >>> >>>Close all the vents on the for the AC. >>>Put the Fan on full. >>>With the vents closed, the back pressure of the air may very well blow >>>the drains clear. >>> >>>I also poured some bleach down there to kill the mold and muck. >>> >>>"MPost" > wrote in message ... >>> >>>>I believe the drain holes where condensate from my air conditioner drains >>>>are plugged up. I don't see any water dripping on the ground when I run >>>>the A/C and I get a faint smell of mildew when I first start up the fan. >>>>Unfortunately, my Chilton's manual doesn't show where these holes are or >>>>how to clear them out. Can anyone give me some pointers and/or point me >>>>to a diagram on the internet? >>>> >>>>Thanks in advance. >>>> >>> >>> >> > > Didn't see what model is being discussed - when I drove a 97 I pulled the blower motor (3 screws) and poured a little water down the ducting from the motor location towards the condenser housing and it dribbled out in the engine bay from a black rubber L-shaped do-dad located low on the firewall about midway. When I had the warm and fuzzies it was draining, I sprayed some (a lot) of anti-bacterial windex down the same vent. It worked for a long while. I also paid to have it down at the dealer - lasted maybe a little longer and smelled a lot cleaner (don't know if that was just fragrance or the dealer did a more thorough/better job). |
#8
|
|||
|
|||
Now that you mention Lysol, It was indeed what I put down the vent, Not
Bleach. It had been long enough since I did it, that I forgot. "Skip" > wrote in message nk.net... > Art wrote: >> Bleach is a bad idea. Residue may damage coils. Lysol spray is better >> choice or purchase foam designed for the purpose from car dealership. I >> am surprised that back pressure could clear it. >> >> >> "Mikus" > wrote in message >> .. . >> >>>I had a musty smell awhile back and fixed it without any disassemble or >>>work. >>> >>>Try this first: >>> >>>Close all the vents on the for the AC. >>>Put the Fan on full. >>>With the vents closed, the back pressure of the air may very well blow >>>the drains clear. >>> >>>I also poured some bleach down there to kill the mold and muck. >>> >>>"MPost" > wrote in message ... >>> >>>>I believe the drain holes where condensate from my air conditioner >>>>drains are plugged up. I don't see any water dripping on the ground when >>>>I run the A/C and I get a faint smell of mildew when I first start up >>>>the fan. Unfortunately, my Chilton's manual doesn't show where these >>>>holes are or how to clear them out. Can anyone give me some pointers >>>>and/or point me to a diagram on the internet? >>>> >>>>Thanks in advance. >>>> >>> >>> >> >> > > I'd be worried about using bleach, especially when your drains are > clogged, unless you enjoy the smell of bleach There are commercial > products made specifically for this, you dump it down the vent intake in > front of your windshield. As for locating the drains, can't help you > there.... > > -- > They that can give up essential liberty to obtain a little temporary > safety deserve neither liberty nor safety. Benjamin Franklin |
#9
|
|||
|
|||
"Jonnie Santos" > wrote in message news:vYEDe.1837$bp.1798@fed1read03... > MPost wrote: >> Interesting idea. I tried the back pressure technique, but unfortunately, >> it didn't work for me. Any other ideas on how to locate and clear the >> drain holes? >> >> "Mikus" > wrote in message >> . .. >> >>>Oh yes, I also believe you need it on reticulate. >>> >>> >>>"Mikus" > wrote in message t... >>> >>>>I had a musty smell awhile back and fixed it without any disassemble or >>>>work. >>>> >>>>Try this first: >>>> >>>>Close all the vents on the for the AC. >>>>Put the Fan on full. >>>>With the vents closed, the back pressure of the air may very well blow >>>>the drains clear. >>>> >>>>I also poured some bleach down there to kill the mold and muck. >>>> >>>>"MPost" > wrote in message ... >>>> >>>>>I believe the drain holes where condensate from my air conditioner >>>>>drains are plugged up. I don't see any water dripping on the ground >>>>>when I run the A/C and I get a faint smell of mildew when I first start >>>>>up the fan. Unfortunately, my Chilton's manual doesn't show where these >>>>>holes are or how to clear them out. Can anyone give me some pointers >>>>>and/or point me to a diagram on the internet? >>>>> >>>>>Thanks in advance. >>>>> >>>> >>>> >>> >> >> > Didn't see what model is being discussed - when I drove a 97 I pulled the > blower motor (3 screws) and poured a little water down the ducting from > the motor location towards the condenser housing and it dribbled out in > the engine bay from a black rubber L-shaped do-dad located low on the > firewall about midway. When I had the warm and fuzzies it was draining, > I sprayed some (a lot) of anti-bacterial windex down the same vent. It > worked for a long while. I also paid to have it down at the dealer - > lasted maybe a little longer and smelled a lot cleaner (don't know if that > was just fragrance or the dealer did a more thorough/better job). |
#10
|
|||
|
|||
My car is a 93 SC-2. I'm a little surprised Chilton's doesn't show how the
drain works...sounds like a pretty basic operation that lots of people would want to do for themselves. "Jonnie Santos" > wrote in message news:vYEDe.1837$bp.1798@fed1read03... > MPost wrote: >> Interesting idea. I tried the back pressure technique, but unfortunately, >> it didn't work for me. Any other ideas on how to locate and clear the >> drain holes? >> >> "Mikus" > wrote in message >> . .. >> >>>Oh yes, I also believe you need it on reticulate. >>> >>> >>>"Mikus" > wrote in message t... >>> >>>>I had a musty smell awhile back and fixed it without any disassemble or >>>>work. >>>> >>>>Try this first: >>>> >>>>Close all the vents on the for the AC. >>>>Put the Fan on full. >>>>With the vents closed, the back pressure of the air may very well blow >>>>the drains clear. >>>> >>>>I also poured some bleach down there to kill the mold and muck. >>>> >>>>"MPost" > wrote in message ... >>>> >>>>>I believe the drain holes where condensate from my air conditioner >>>>>drains are plugged up. I don't see any water dripping on the ground >>>>>when I run the A/C and I get a faint smell of mildew when I first start >>>>>up the fan. Unfortunately, my Chilton's manual doesn't show where these >>>>>holes are or how to clear them out. Can anyone give me some pointers >>>>>and/or point me to a diagram on the internet? >>>>> >>>>>Thanks in advance. >>>>> >>>> >>>> >>> >> >> > Didn't see what model is being discussed - when I drove a 97 I pulled the > blower motor (3 screws) and poured a little water down the ducting from > the motor location towards the condenser housing and it dribbled out in > the engine bay from a black rubber L-shaped do-dad located low on the > firewall about midway. When I had the warm and fuzzies it was draining, > I sprayed some (a lot) of anti-bacterial windex down the same vent. It > worked for a long while. I also paid to have it down at the dealer - > lasted maybe a little longer and smelled a lot cleaner (don't know if that > was just fragrance or the dealer did a more thorough/better job). |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Drain holes | [email protected] | Saturn | 3 | June 9th 05 10:22 PM |
91 Integra Condenser Fan Keeps Running | sean | Honda | 1 | January 19th 05 04:23 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 10 | December 2nd 04 05:19 AM |
Drain holes | ISando | Mazda | 0 | November 17th 04 02:06 PM |
In-the-tank fuel pumps cause death and destruction | Silver Surfer | Chrysler | 293 | November 7th 04 03:41 PM |