If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
help with clutch disengage issue please?
|
Ads |
#12
|
|||
|
|||
help with clutch disengage issue please?
On Thu, 18 May 2006 20:03:50 GMT, "Carjunky via CarKB.com"
<u21895@uwe> wrote: >how do i check hight and throwout travel? Fron travel you measue the stroke of the slave cylinder when pedeal is depressed one time. For hieght, you measure how high the throughout bearing collar ring on pressure plate is from flywheel when it is bolt to it (if you have acces to old clutch and pressure plate you can compare this) ----------------- The SnoMan www.thesnoman.com |
#13
|
|||
|
|||
help with clutch disengage issue please?
SnoMan wrote:
>>how do i check hight and throwout travel? > >Fron travel you measue the stroke of the slave cylinder when pedeal is >depressed one time. For hieght, you measure how high the throughout >bearing collar ring on pressure plate is from flywheel when it is bolt >to it (if you have acces to old clutch and pressure plate you can >compare this) >----------------- >The SnoMan >www.thesnoman.com The height on the new pressure plate is slightly more, i believe this is just between manufacture. What are the correct bolt torque for the presure plate? thank you -- Message posted via http://www.carkb.com |
#14
|
|||
|
|||
help with clutch disengage issue please?
On Fri, 19 May 2006 13:56:15 GMT, "Carjunky via CarKB.com"
<u21895@uwe> wrote: >The height on the new pressure plate is slightly more, i believe this is just >between manufacture This is not good, it should be less because with a new clutch disc the plate will be retracted more before you disengage it. (this height increases as clutchs wear so it should start out lower) Height "should" be the same or less than old one. I do not have torque spec handy but I can dig it up if need but usually it is in the range 35 to 50 ft lbs depending on bolt size. ----------------- The SnoMan www.thesnoman.com |
#15
|
|||
|
|||
help with clutch disengage issue please?
well let's make sure we got one thing straight first.the height is measured
up to the top of the fingers on the pressure plate that the throwout bearing rides on, right? -- Message posted via http://www.carkb.com |
#16
|
|||
|
|||
help with clutch disengage issue please?
Specifying what i just said. The pressure plat laid face down, measured from
the ground to the top of the fingers, the new one is about 1/8" taller than the old one. -- Message posted via CarKB.com http://www.carkb.com/Uwe/Forums.aspx/saturn/200605/1 |
#17
|
|||
|
|||
help with clutch disengage issue please?
On Fri, 19 May 2006 16:56:04 GMT, "Carjunky via CarKB.com"
<u21895@uwe> wrote: >well let's make sure we got one thing straight first.the height is measured >up to the top of the fingers on the pressure plate that the throwout bearing >rides on, right? Correct. ----------------- The SnoMan www.thesnoman.com |
#18
|
|||
|
|||
help with clutch disengage issue please?
On Fri, 19 May 2006 17:09:44 GMT, "Carjunky via CarKB.com"
<u21895@uwe> wrote: >Specifying what i just said. The pressure plat laid face down, measured from >the ground to the top of the fingers, the new one is about 1/8" taller than >the old one. But is this mounted to flywheel or not (with clucth disc installed) ----------------- The SnoMan www.thesnoman.com |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
new clutch slips :( | [email protected] | 4x4 | 13 | August 5th 05 07:41 AM |
new clutch slips :( | [email protected] | Technology | 3 | July 13th 05 08:19 PM |
clutch won't disengage.. i think | Sk8rgrrl22 | Honda | 3 | March 14th 05 12:52 PM |
Wrong Clutch Fork? | Michael White | Jeep | 6 | February 8th 05 02:33 AM |
stuck caliper... | Abeness | Honda | 113 | December 7th 04 01:22 AM |