If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
2001 Caravan 3.8L - Seized Spark Plug
Have a 2001 Grand Caravan that was at the shop today (3.8L engine w/82K
miles.) The Service Manager indicated they could not do a tune-up due to the fact that one of the plugs on the front bank was seized in the head and he was afraid to strip the head out. Any idea how prevalent a seized plug is in this engine and what the success is of trying to get them out without tearing the threads out of the head? |
Ads |
#2
|
|||
|
|||
Randy wrote:
> Have a 2001 Grand Caravan that was at the shop today (3.8L engine w/82K > miles.) The Service Manager indicated they could not do a tune-up due > to the fact that one of the plugs on the front bank was seized in the > head and he was afraid to strip the head out. > > Any idea how prevalent a seized plug is in this engine and what the > success is of trying to get them out without tearing the threads out of > the head? > It isn't uncommon if you fail to use anti-sieze on the threads when you install them. Tearing out the threads isn't all that big of a deal as you can put in a helicoil. Matt |
#3
|
|||
|
|||
"Randy" > wrote in message oups.com... > Have a 2001 Grand Caravan that was at the shop today (3.8L engine w/82K > miles.) The Service Manager indicated they could not do a tune-up due > to the fact that one of the plugs on the front bank was seized in the > head and he was afraid to strip the head out. > > Any idea how prevalent a seized plug is in this engine and what the > success is of trying to get them out without tearing the threads out of > the head? Those platinum plugs stay in for so long, this is probably your first replacement/????.. you can soak them with a penetrating oil, I recommend rust penetrate from Chrysler, it works great, soak them over night and try to remove them cold. Glenn Beasley Chrysler Tech |
#4
|
|||
|
|||
I believe the plugs were replaced by the same dealer at ~ 30K miles. So
what can you offer on how often this might happen and how offen the penetrating oil is successful (what are the odds that the Dodge dealer gets it out without charging me to replace a head?)? |
#5
|
|||
|
|||
"Randy" > writes:
> I believe the plugs were replaced by the same dealer at ~ 30K miles. So > what can you offer on how often this might happen and how offen the > penetrating oil is successful (what are the odds that the Dodge dealer > gets it out without charging me to replace a head?)? See the previous remark on heli-coils. And a heli-coil might not even be necessary. You take the plug out, using whatever violence is necessary. This will tear up the threads. Now you put a thread-cleaner through the hole. In my experience, this will normally end up with threads that work well enough to get compression, which is all you really need. If this isn't good enough, you re-thread the hole with a bigger tap, and put in an insert called a heli-coil. In Nomen Nescio's ideal world of $150,000 Neons, all aluminum heads would have heli-coils installed at the factory. It's really hard to imagine taking out a seized plug causing so much damage that a heli-coil can't fix it. If the service writer seems to be uncomfortable with this idea, something is really wrong. -- Joseph J. Pfeiffer, Jr., Ph.D. Phone -- (505) 646-1605 Department of Computer Science FAX -- (505) 646-1002 New Mexico State University http://www.cs.nmsu.edu/~pfeiffer |
#6
|
|||
|
|||
Joe Pfeiffer wrote:
> It's really hard to imagine taking out a seized plug causing so much > damage that a heli-coil can't fix it. If the service writer seems to > be uncomfortable with this idea, something is really wrong. Yes, it may be time to switch to another shop. Matt |
#7
|
|||
|
|||
See E mail
"Randy" > wrote in message oups.com... > I believe the plugs were replaced by the same dealer at ~ 30K miles. So > what can you offer on how often this might happen and how offen the > penetrating oil is successful (what are the odds that the Dodge dealer > gets it out without charging me to replace a head?)? > |
#8
|
|||
|
|||
!00k platinum plugs in that engine, replaced at that mileage unless there is
a problem, soak the plugs over nite, remove them from a cold engine and they should pop out, anytime you remove hot steel from hot aluminum metal, problems like this happen, that goes with changing your engine oil also, steel drain plug + aluminum pan= damaged threads when hot. "Randy" > wrote in message oups.com... > I believe the plugs were replaced by the same dealer at ~ 30K miles. So > what can you offer on how often this might happen and how offen the > penetrating oil is successful (what are the odds that the Dodge dealer > gets it out without charging me to replace a head?)? > |
#9
|
|||
|
|||
maxpower wrote:
> !00k platinum plugs in that engine, replaced at that mileage unless there is > a problem, soak the plugs over nite, remove them from a cold engine and they > should pop out, anytime you remove hot steel from hot aluminum metal, > problems like this happen, that goes with changing your engine oil also, > steel drain plug + aluminum pan= damaged threads when hot. Really? I've heard just the opposite. AL expands at a rate higher than steel. Steel plug inside of aluminum will get looser as the temp goes up. Matt |
#10
|
|||
|
|||
hey glenn
i found out a neat thing that happens with the rust pen. from mopar when you soak something with it then heat up the area, when the bubbles show themselfs around the bolt/nut it ready to come out easy maxpower wrote: > "Randy" > wrote in message > oups.com... > > Have a 2001 Grand Caravan that was at the shop today (3.8L engine w/82K > > miles.) The Service Manager indicated they could not do a tune-up due > > to the fact that one of the plugs on the front bank was seized in the > > head and he was afraid to strip the head out. > > > > Any idea how prevalent a seized plug is in this engine and what the > > success is of trying to get them out without tearing the threads out of > > the head? > > Those platinum plugs stay in for so long, this is probably your first > replacement/????.. you can soak them with a penetrating oil, I recommend > rust penetrate from Chrysler, it works great, soak them over night and try > to remove them cold. > > Glenn Beasley > Chrysler Tech |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
removing stripped spark plug - suggestions? | pws | Mazda | 16 | April 18th 05 11:17 PM |
Advice and Help With Removing Broken Spark Plug | BibBob5 | Ford Explorer | 0 | February 23rd 05 11:31 PM |
Broken Spark Plug - Need help fast | Daniel J. Stern | Dodge | 5 | January 31st 05 10:33 PM |
Broken Spark Plug - Need help fast | Daniel J. Stern | Technology | 0 | January 27th 05 05:07 AM |
Twisted-off Spark plug Threads Removed | Gene Gardner | General | 0 | October 5th 04 07:08 PM |