If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Civic problem solved!
Well I replaced the main relay and ignition switch and it still died out
after a few minutes of driving. When it cooled off there was spark again and it would start and run until it got hot again. So I put in a new igniter from Napa. That seems to have cured the problem. At least for now! I still don't know why the igniters in my vehicle only seem to last a year or two................But they have not been genuine Honda parts.......... thanks for all your excellent help Gary in Hawaii 91 Civic Hatchback, 178k miles |
#2
|
|||
|
|||
Ropert's Aloha wrote: > > Well I replaced the main relay and ignition switch and it still died out > after a few minutes of driving. When it cooled off there was spark again and > it would start and run until it got hot again. So I put in a new igniter > from Napa. That seems to have cured the problem. At least for now! I still > don't know why the igniters in my vehicle only seem to last a year or > two................But they have not been genuine Honda parts.......... Having followed this NG for a few years, I remember several posters reporting that after market igniters (ICMs) don't last long. |
#3
|
|||
|
|||
Hi
Just making su Did you put heatsink compound on the device? (Radio Shack sells it) It is supposed to have that stuff between the device and its mounting plate. If you didn't do that, I'd suggest you redo it because it might cause problems for you a while from now. Regards, Remco |
#4
|
|||
|
|||
> Just making su > Did you put heatsink compound on the device? (Radio Shack sells it) It > is supposed to have that stuff between the device and its mounting > plate. If you didn't do that, I'd suggest you redo it because it might > cause problems for you a while from now. No, Ididn't use any. None even came with the igniter I bought at Napa. I went to Radio Shack out here in Hawaii and the kid in the store looked like he had never heard of it. I searched the store and found nothing. Then I went to Napa and the only thing close was a Silicone Dielectric by Permatex for Ford and GM to protect from moisture. It didn't really mention protection from heat. I almost went for it, but thought maybe Comp USA would have something like it. I even went to Ace Hardware and they had nothing. So do you put the grease in between the little mounting plate that is bolted onto the inside of the distributor? And how much? There was a very tiny thin coat of a type of clear grease on it when I took it out, but didn't seem like it was between the mounting plate and igniter unit, but myabe it really was. thanks for the heads up Gary Hawaii |
#5
|
|||
|
|||
"Ropert's Aloha" > wrote
> > Just making su > > Did you put heatsink compound on the device? (Radio Shack sells it) It > > is supposed to have that stuff between the device and its mounting > > plate. If you didn't do that, I'd suggest you redo it because it might > > cause problems for you a while from now. > > > No, Ididn't use any. None even came with the igniter I bought at Napa. I > went to Radio Shack out here in Hawaii and the kid in the store looked like > he had never heard of it. I searched the store and found nothing. Then I > went to Napa and the only thing close was a Silicone Dielectric by Permatex > for Ford and GM to protect from moisture. It didn't really mention > protection from heat. I almost went for it, but thought maybe Comp USA would > have something like it. I even went to Ace Hardware and they had nothing. So > do you put the grease in between the little mounting plate that is bolted > onto the inside of the distributor? And how much? There was a very tiny thin > coat of a type of clear grease on it when I took it out, but didn't seem > like it was between the mounting plate and igniter unit, but myabe it really > was. I installed a new igniter a couple of years ago in my 91 Civic. IIRC, I went to a place like CarQuest, Autozone, Checkers, or Advance, and they had some. The clerks knew what I was talking about. Maybe call one of these stores and ask. |
#6
|
|||
|
|||
Ropert's Aloha wrote:
> > > Just making su > > Did you put heatsink compound on the device? (Radio Shack sells it) It > > is supposed to have that stuff between the device and its mounting > > plate. If you didn't do that, I'd suggest you redo it because it might > > cause problems for you a while from now. > > No, Ididn't use any. None even came with the igniter I bought at Napa. I > went to Radio Shack out here in Hawaii and the kid in the store looked like > he had never heard of it. I searched the store and found nothing. Yep, that's Radio Shack, the corporate motto is: You've got questions, we have blank stares! Hehehe... They sell it, it's called "heat sink compound", here's the info from their website: 273-1372 RadioShack Heat Sink Compound Also, any electronics store such as Fry's will have it, it's the same stuff used on heatsinks for computer processor heatsinks and cooling fans. JazzMan -- ************************************************** ******** Please reply to jsavage"at"airmail.net. Curse those darned bulk e-mailers! ************************************************** ******** "Rats and roaches live by competition under the laws of supply and demand. It is the privilege of human beings to live under the laws of justice and mercy." - Wendell Berry ************************************************** ******** |
#7
|
|||
|
|||
Look on my website under "Cars" for the description of changing the ignition control module (igniter?) on my car. I used dielectric heat sink paste from an electronics store, a small blister pack for $1 (Canadian) last spring. I did some research on it with a lot of help from people in this newsgroup. The distributor (pun?) of the Japanese part was Standard in the USA and I belive they sell the little bubble packs, their Canadian subsidiary Blue Streak does. At $1 a shot I don't know why they don't just stick one in the box with the expensive part. www.ncf.ca/~ag384/top.htm -- ------------------------------------------------------------------------------ William R Watt National Capital FreeNet Ottawa's free community network homepage: www.ncf.ca/~ag384/top.htm warning: non-FreeNet email must have "notspam" in subject or it's returned |
#8
|
|||
|
|||
William R. Watt wrote:
> > Look on my website under "Cars" for the description of changing the > ignition control module (igniter?) on my car. I used dielectric heat sink > paste from an electronics store, a small blister pack for $1 (Canadian) > last spring. I did some research on it with a lot of help from people in > this newsgroup. The distributor (pun?) of the Japanese part was Standard > in the USA and I belive they sell the little bubble packs, their Canadian > subsidiary Blue Streak does. At $1 a shot I don't know why they don't just > stick one in the box with the expensive part. www.ncf.ca/~ag384/top.htm > Because the real cost of that grease is far less than a penny a shot. The little package costs more than the contents. The reason they don't put it in is because getting you to part with a buck for essentially 2c worth of product is good for the bottom line. I bought a large tube, I think 8-12 oz, for less than $10 a long time ago, it will last me the rest of my life. JazzMan -- ************************************************** ******** Please reply to jsavage"at"airmail.net. Curse those darned bulk e-mailers! ************************************************** ******** "Rats and roaches live by competition under the laws of supply and demand. It is the privilege of human beings to live under the laws of justice and mercy." - Wendell Berry ************************************************** ******** |
#9
|
|||
|
|||
The silicone dielectric grease is what you were looking for. BTDT.
I used it under a new ignition module in my car as a heat insulator as per the FSM. Also use it on plug wires at both ends to keep out moisture and prevent arcing. FWIW YMMV DFB On Sat, 18 Dec 2004 22:03:04 GMT, "Ropert's Aloha" > wrote: > >> Just making su >> Did you put heatsink compound on the device? (Radio Shack sells it) It >> is supposed to have that stuff between the device and its mounting >> plate. If you didn't do that, I'd suggest you redo it because it might >> cause problems for you a while from now. > > >No, Ididn't use any. None even came with the igniter I bought at Napa. I >went to Radio Shack out here in Hawaii and the kid in the store looked like >he had never heard of it. I searched the store and found nothing. Then I >went to Napa and the only thing close was a Silicone Dielectric by Permatex >for Ford and GM to protect from moisture. It didn't really mention >protection from heat. I almost went for it, but thought maybe Comp USA would >have something like it. I even went to Ace Hardware and they had nothing. So >do you put the grease in between the little mounting plate that is bolted >onto the inside of the distributor? And how much? There was a very tiny thin >coat of a type of clear grease on it when I took it out, but didn't seem >like it was between the mounting plate and igniter unit, but myabe it really >was. > >thanks for the heads up > >Gary >Hawaii > "When a legislature undertakes to proscribe the exercise of a citizen's constitutional rights it acts lawlessly and the citizen can take matters into his own hands and proceed on the basis that such a law is no law at all." - Justice William O. Douglas |
#10
|
|||
|
|||
It's better to use "dielectric heat transfer grease". Compare the specs to the "dielectric grease". Not the same. The technician at Blue Streak looked at the specs on the website of the stuff I used and said it was good but Blue Streak recommends a grease of their own. The stuff sold at the auto parts store for spark plugs is not the same stuff. MisterSkippy ) writes: > The silicone dielectric grease is what you were looking for. BTDT. > I used it under a new ignition module in my car as a heat insulator as > per the FSM. Also use it on plug wires at both ends to keep out > moisture and prevent arcing. > FWIW > YMMV > DFB > > On Sat, 18 Dec 2004 22:03:04 GMT, "Ropert's Aloha" > > wrote: > >> >>> Just making su >>> Did you put heatsink compound on the device? (Radio Shack sells it) It >>> is supposed to have that stuff between the device and its mounting >>> plate. If you didn't do that, I'd suggest you redo it because it might >>> cause problems for you a while from now. >> >> >>No, Ididn't use any. None even came with the igniter I bought at Napa. I >>went to Radio Shack out here in Hawaii and the kid in the store looked like >>he had never heard of it. I searched the store and found nothing. Then I >>went to Napa and the only thing close was a Silicone Dielectric by Permatex >>for Ford and GM to protect from moisture. It didn't really mention >>protection from heat. I almost went for it, but thought maybe Comp USA would >>have something like it. I even went to Ace Hardware and they had nothing. So >>do you put the grease in between the little mounting plate that is bolted >>onto the inside of the distributor? And how much? There was a very tiny thin >>coat of a type of clear grease on it when I took it out, but didn't seem >>like it was between the mounting plate and igniter unit, but myabe it really >>was. >> >>thanks for the heads up >> >>Gary >>Hawaii >> > > > > > > "When a legislature undertakes to proscribe the exercise of a citizen's > constitutional rights it acts lawlessly and the citizen can take matters into > his own hands and proceed on the basis that such a law is no law at all." > - Justice William O. Douglas -- ------------------------------------------------------------------------------ William R Watt National Capital FreeNet Ottawa's free community network homepage: www.ncf.ca/~ag384/top.htm warning: non-FreeNet email must have "notspam" in subject or it's returned |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Civic problem solved! | Ropert's Aloha | Honda | 8 | December 21st 04 12:31 AM |
New *FREE* Corvette Discussion Forum | JLA ENTERPRISES TECHNOLOGIES INTEGRATION | Corvette | 12 | November 30th 04 06:36 PM |
88 civic starter problem? | Jeremy | Honda | 13 | November 3rd 04 06:40 PM |
2000 Honda Civic Power Window Problem | [email protected] | Honda | 6 | October 31st 04 01:46 AM |
Chevy Venture airbag light - problem solved | Katy | General | 0 | February 21st 04 12:29 AM |