If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#21
|
|||
|
|||
4.10 and 4.11 are functional equivelents. That means they are the same ...
"Patrick Ô¿Ô" > wrote in message ... > My Rubi came with 4.11 gears. It is a 2005 Unlimited Rubicon. > > Patrick > Ô¿Ô > > > "J Strickland" > wrote in message > ... >> Rubis come with the 4.0L and 4.10 gears. >> >> >> >> >> "Carl Saiyed" > wrote in message >> ... >>>I thought so, but the 4.10's threw me off. >>> >>> Carl >>> >>> >>> "JimG" > wrote in message >>> ... >>>> Carl, the Rubicon only comes with the 4.0L >>>> >>>> -- >>>> JimG >>>> 80' CJ-7 258 CID, HEI >>>> 4.56 Gears, Lock-Right F&R >>>> 35" BFG MT on 15x10 Centerlines >>>> D44 Rear, D30 Front. SOA >>>> Dana 300 w/4:1 & Currie twin sticks >>>> Warn X8000i w/ dual batteries >>>> >>>> 00' TJ Sport 4.0L, 5sp >>>> 4.56 Gears, TrueTrac rear >>>> 33" BFG AT on 15x8 Eagle Alloys >>>> D35 Rear, D30 Front. 3" Suspension Lift >>>> >>>> "Carl Saiyed" > wrote in message >>>> ... >>>> > I'm pushing 33's thru 4.10's with my 4cyl on my 89 YJ. Flat roads are >>>> > no >>>> > problem, large hills slow me down to about 55mph or less. The 6cyl >>>> > thru >>>> > 4.10's will fare much better. Which engine do you have? >>>> > >>>> > Carl >>>> > >>>> > >>>> > >>>> > >>>> > "Fred Garvin" > wrote in message >>>> > news >>>> >> I'm planning to put 33" MTRs on my Rubicon. I love the way that it >>> will >>>> >> idle up a hill with the 31s. Will it still do that with 33s and >>>> >> 4.10s? >>>> >> >>>> >> Thanks! >>>> >> >>>> >> -Fred >>>> >> >>>> >> >>>> > >>>> > >>>> >>>> >>> >>> >> >> > > |
Ads |
#22
|
|||
|
|||
J Strickland wrote: > 4.10 and 4.11 are functional equivelents. That means they are the same ... Exactly. And they are only off that .01 because of the difference in front and rear ring gear diameters. The .01 is insignificant offroad. Jerry > > "Patrick Ô¿Ô" > wrote in message > ... > >>My Rubi came with 4.11 gears. It is a 2005 Unlimited Rubicon. >> >>Patrick >>Ô¿Ô >> >> >>"J Strickland" > wrote in message ... >> >>>Rubis come with the 4.0L and 4.10 gears. >>> >>> >>> >>> >>>"Carl Saiyed" > wrote in message ... >>> >>>>I thought so, but the 4.10's threw me off. >>>> >>>>Carl >>>> >>>> >>>>"JimG" > wrote in message ... >>>> >>>>>Carl, the Rubicon only comes with the 4.0L >>>>> >>>>>-- >>>>>JimG >>>>>80' CJ-7 258 CID, HEI >>>>>4.56 Gears, Lock-Right F&R >>>>>35" BFG MT on 15x10 Centerlines >>>>>D44 Rear, D30 Front. SOA >>>>>Dana 300 w/4:1 & Currie twin sticks >>>>>Warn X8000i w/ dual batteries >>>>> >>>>>00' TJ Sport 4.0L, 5sp >>>>>4.56 Gears, TrueTrac rear >>>>>33" BFG AT on 15x8 Eagle Alloys >>>>>D35 Rear, D30 Front. 3" Suspension Lift >>>>> >>>>>"Carl Saiyed" > wrote in message ... >>>>> >>>>>>I'm pushing 33's thru 4.10's with my 4cyl on my 89 YJ. Flat roads are >>>>>>no >>>>>>problem, large hills slow me down to about 55mph or less. The 6cyl >>>>>>thru >>>>>>4.10's will fare much better. Which engine do you have? >>>>>> >>>>>>Carl >>>>>> >>>>>> >>>>>> >>>>>> >>>>>>"Fred Garvin" > wrote in message >>>>>>news >>>>>> >>>>>>>I'm planning to put 33" MTRs on my Rubicon. I love the way that it >>>> >>>>will >>>> >>>>>>>idle up a hill with the 31s. Will it still do that with 33s and >>>>>>>4.10s? >>>>>>> >>>>>>>Thanks! >>>>>>> >>>>>>>-Fred >>>>>>> >>>>>>> >>>>>> >>>>>> >>>>> >>>> >>> >> > > -- Jerry Bransford PP-ASEL N6TAY See the Geezer Jeep at http://members.cox.net/jerrypb/ |
#23
|
|||
|
|||
Jerry Bransford wrote:
> > > J Strickland wrote: > >> 4.10 and 4.11 are functional equivelents. That means they are the same >> ... > > > Exactly. And they are only off that .01 because of the difference in > front and rear ring gear diameters. The .01 is insignificant offroad. > A 4.10 gear set has 41 teeth on the ring and 10 teeth on the pinion, and a 4.11 has 37 and 9. Roughly a 1/4"/rev rolling distance difference with 33s. Close enough. -- jeff |
#24
|
|||
|
|||
Hi Steve,
Geez, I didn't catch the tooth change the last time you showed me this Japanese crap. God Bless America, ßill O|||||||O http://www.billhughes.com/ Steve wrote: > > Mr. Strickland is correct. The Rubicon Dana 44 TruLok carrier is an odd > duck with a 'thick' ring gear (no carrier break), hence a smaller 10 > tooth pinion on a 41 tooth ring: > > http://xjeep.dyndns.org/trulok/slides/IMG_7878.html > > Steve > http://xjeep.dyndns.org |
#25
|
|||
|
|||
One inch.
God Bless America, ßill O|||||||O http://www.billhughes.com/ jeff wrote: > > A 4.10 gear set has 41 teeth on the ring and 10 teeth on the pinion, and > a 4.11 has 37 and 9. Roughly a 1/4"/rev rolling distance difference with > 33s. Close enough. > > -- > jeff |
#26
|
|||
|
|||
Back to school Bill.
L.W.(ßill) Hughes III wrote: > One inch. > God Bless America, ßill O|||||||O > http://www.billhughes.com/ > > jeff wrote: > >>A 4.10 gear set has 41 teeth on the ring and 10 teeth on the pinion, and >>a 4.11 has 37 and 9. Roughly a 1/4"/rev rolling distance difference with >>33s. Close enough. >> >>-- >>jeff |
#27
|
|||
|
|||
Ok. thanks. Now I know what gears I really have
Patrick Ô¿Ô "Steve" > wrote in message news:lJ4Ee.166535$on1.22715@clgrps13... > Mr. Strickland is correct. The Rubicon Dana 44 TruLok carrier is an odd > duck with a 'thick' ring gear (no carrier break), hence a smaller 10 tooth > pinion on a 41 tooth ring: > > http://xjeep.dyndns.org/trulok/slides/IMG_7878.html > > Steve > http://xjeep.dyndns.org > > > Dave Milne wrote: >> yes, and now you really are nitpicking. >> >> But for the sake of completeness. >> >> The Dana 44 came with a 4.10 ish ratio of 45/11 or 4.09 >> The Dana 30 with 41/10 or 4.10 exactly >> The Dana 35 came with 37/9 or 4.11. >> >> So whatever Jeep advertised the Dana 30/35 combo to be (4.10 I think) >> they would have been wrong for one axle. >> >> Dave Milne, Scotland >> '91 Grand Wagoneer, '99 TJ >> >> "Patrick Ô¿Ô" > wrote in message >> ... >> >>>In other words it's false advertising on the part of Jeep. >>> >>>Patrick >>>Ô¿Ô >>> >>> >>>"L.W. ("ßill") Hughes III" > wrote in message ... >>> >>>> Nick picking, the Dana 44 is a 4.09 ratio, as it's tooth count is >>>>11 and 45: http://www.billhughes.com/tooth_count.txt >>>> God Bless America, ßill O|||||||O >>>> >>>>"Patrick Ô¿Ô" wrote: >>>> >>>>>My Rubi came with 4.11 gears. It is a 2005 Unlimited Rubicon. >>>>> >>>>>Patrick >>>>>Ô¿Ô >>> >>> >> |
#28
|
|||
|
|||
33" diameter, times Pi (3.14159) for the circumference, times .01
equals the change in inches. God Bless America, ßill O|||||||O http://www.billhughes.com/ RoyJ wrote: > > Back to school Bill. > > L.W.(ßill) Hughes III wrote: > > One inch. > > God Bless America, ßill O|||||||O > > http://www.billhughes.com/ > > > > jeff wrote: > > > >>A 4.10 gear set has 41 teeth on the ring and 10 teeth on the pinion, and > >>a 4.11 has 37 and 9. Roughly a 1/4"/rev rolling distance difference with > >>33s. Close enough. > >> > >>-- > >>jeff |
#29
|
|||
|
|||
no, 33 x pi = 103.67" for the circumference.
Difference is between 4.11 and 4.10, so multiply that by 0.01/4.11 = 0.25" as Jeff said. Dave Milne, Scotland '91 Grand Wagoneer, '99 TJ "L.W. (ßill) Hughes III" > wrote in message ... > 33" diameter, times Pi (3.14159) for the circumference, times .01 > equals the change in inches. > God Bless America, ßill O|||||||O > http://www.billhughes.com/ > > RoyJ wrote: > > > > Back to school Bill. > > > > L.W.(ßill) Hughes III wrote: > > > One inch. > > > God Bless America, ßill O|||||||O > > > http://www.billhughes.com/ > > > > > > jeff wrote: > > > > > >>A 4.10 gear set has 41 teeth on the ring and 10 teeth on the pinion, and > > >>a 4.11 has 37 and 9. Roughly a 1/4"/rev rolling distance difference with > > >>33s. Close enough. > > >> > > >>-- > > >>jeff |
#30
|
|||
|
|||
Right. Somehow I jumped to .01 as being one percent.
God Bless America, ßill O|||||||O http://www.billhughes.com/ Dave Milne wrote: > > no, 33 x pi = 103.67" for the circumference. > Difference is between 4.11 and 4.10, so multiply that by 0.01/4.11 = 0.25" > as Jeff said. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Power Adding Steps | [email protected] | Ford Mustang | 7 | February 23rd 05 07:56 PM |
Ran at the track last night!! | Erik D. | Ford Mustang | 13 | November 29th 04 03:36 AM |
ATI Catalyst 4.10's Released | Pete | Simulators | 1 | October 15th 04 04:21 PM |