If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
1996 Neon stalling problems
My g/f has a 1996 Neon with about 130 K miles on it. While she puts
less than 10K miles on the car a year, she has neglected to get ANY work done to it. About 3 months ago it developed a problem of suddenly dying while driving. It usually would die within 10 miles or about 20 minutes of driving. If you then let it sit for 5-20 minutes, the car will fire right up again and run another 5- 10 miles before doing it again. We took it to a shop and they did some basic maintenance, scanned the codes and repaired a faulty wiring connection somewhere beneath the battery tray. They also replaced the fuel filter. Well, it didn't fix the problem. This weekend I drove the car around and again confirmed the original fault, sudden stalling after about 15 miles of driving. I have now replaced the coil, spark plug wires, spark plugs, oil and air filters, gave it an oil change, the basics. I will do a scan check shortly, and am now faced with driving the car myself to see if I repaired it. Are there any other possible causes that I might be missing that can cause this? Thanks! |
Ads |
#2
|
|||
|
|||
1996 Neon stalling problems
If the vehilces slowly looses power then cuts off you may have a fuel pump
problem. Test the fuel pressure. If all is good find out what code is present and also state what codes were found at the shop you said did the work on it. Glenn Beasley Chrysler Tech |
#3
|
|||
|
|||
1996 Neon stalling problems
damnnickname wrote: > If the vehilces slowly looses power then cuts off you may have a fuel pump > problem. Test the fuel pressure. If all is good find out what code is > present and also state what codes were found at the shop you said did the > work on it. > > Glenn Beasley > Chrysler Tech Hey Glenn, thanks for the reply! I don't have a fule pressure gauge, and the codes are 11, 12 and 43. I am thinking this is crankshaft sensor related from what I've read up on the net. I took the car out for a spin the other day, and you could slowly feel the hesitation coming on after 15 minutes of driving/10 miles or so. Upon accelleration, the car starts to hesitate a tiny bit, but over 5 minutes gets worse. WHen the car really starts to shake, the engine will die when you come to a stop. Let it sit for 3 minutes or so and it starts right back up and will run for another 10 miles or so. Now for the current problem. The new style OEM crankshaft sensor that I bought today also needed the purchase of a new wiring adapter to adapt it to the old wiring harness. I'm an electronics tech, the crimping and splicing isn't an issue, but there were no instructions with the new wires and connectors. When I asked the dealer to give me a printout, they refused, saying that I should know what I was doing. (strong letter to dealer to follow!) ANyways, can you advise how to connect the new sensor to the old wiring harness? Thanks! Curt |
#4
|
|||
|
|||
1996 Neon stalling problems
"Curt" > wrote in message oups.com... > > damnnickname wrote: > > If the vehilces slowly looses power then cuts off you may have a fuel pump > > problem. Test the fuel pressure. If all is good find out what code is > > present and also state what codes were found at the shop you said did the > > work on it. > > > > Glenn Beasley > > Chrysler Tech > > Hey Glenn, thanks for the reply! I don't have a fule pressure gauge, > and the codes are 11, 12 and 43. I am thinking this is crankshaft > sensor related from what I've read up on the net. I took the car out > for a spin the other day, and you could slowly feel the hesitation > coming on after 15 minutes of driving/10 miles or so. Upon > accelleration, the car starts to hesitate a tiny bit, but over 5 > minutes gets worse. WHen the car really starts to shake, the engine > will die when you come to a stop. Let it sit for 3 minutes or so and it > starts right back up and will run for another 10 miles or so. > > Now for the current problem. The new style OEM crankshaft sensor that I > bought today also needed the purchase of a new wiring adapter to adapt > it to the old wiring harness. I'm an electronics tech, the crimping > and splicing isn't an issue, but there were no instructions with the > new wires and connectors. When I asked the dealer to give me a > printout, they refused, saying that I should know what I was doing. > (strong letter to dealer to follow!) > > ANyways, can you advise how to connect the new sensor to the old wiring > harness? > > Thanks! > Curt > They cant give it to you because they have no idea, The last one I did I believe there were directions in it but the color wires didn't match what the directions said so and the wires aren't in the same places so I used trial and error. I think the only color that was the same was ground, the blue wire. The other thing is if the connector is ok and not damaged, take those parts back to the dealer and go to an after market parts store, they will give you the sensor that does not require the harness Glenn Beasley Chrysler Tech |
#5
|
|||
|
|||
1996 Neon stalling problems
OK, thanks! I can meter the old and new sensors on the bench, so I'll
figure it out. All electrical parts at this dealership are sold as non returnable items. and the one aftermarket store I went to said it was an OEM part only, apparently not though. Canada stinks when it comes to stuff like this and availability, I run across the same with electronics parts and availability. Thanks again though! Curt |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Auto Trans problems 1996 318ti | [email protected] | BMW | 0 | November 8th 05 06:05 PM |
1997 Plymouth Neon starter problems | davage | Dodge | 2 | October 31st 05 07:51 AM |
1997 Neon engine light and other problems | endunk | Dodge | 1 | October 5th 05 06:05 AM |
Problems with 1996 A4 | John Young | Audi | 2 | June 4th 04 07:44 PM |