If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Clutch Replacement
I have a 95 Explorer with 245000 miles on it. My son decided to
take it four wheeling last wheel and fried the clutch while changing gears on a steep ascent. Now both him and I will have the pleasure of learning how to replace a clutch. I've started doing some preliminary research and it appears a lot must come off. It starts with the clutch master cylinder, transfer case, and transmission itself. I'm looking for links to clutch replacement guides for this vehicle and possibly a contact I can ask questions of as we go along. Tonight I will get the vehicle off the ground and start looking at what we are up against. This is a perfect car to learn on since it is not worth much but is good for getting around in the snow and hauling a trailer. Thanks, Mark |
Ads |
#2
|
|||
|
|||
Clutch Replacement
If your 95 is anything like my 93, this job is tough. The toughest part by
far is getting the driveshaft removed. The bolts are very small (10 mm?) and are loctited on. The small clearance means lots of turns of the wrench. I paid $495 to a mechanic to do this job the second time. I like to work on my truck, but... some jobs are just too exhausting. "Mark Barrett" > wrote in message ... > I have a 95 Explorer with 245000 miles on it. My son decided to > take it four wheeling last wheel and fried the clutch while changing > gears on a steep ascent. Now both him and I will have the pleasure of > learning how to replace a clutch. I've started doing some preliminary > research and it appears a lot must come off. It starts with the clutch > master cylinder, transfer case, and transmission itself. I'm looking > for links to clutch replacement guides for this vehicle and possibly a > contact I can ask questions of as we go along. Tonight I will get the > vehicle off the ground and start looking at what we are up against. > This is a perfect car to learn on since it is not worth much but is > good for getting around in the snow and hauling a trailer. > Thanks, > Mark > |
#3
|
|||
|
|||
Clutch Replacement
TeflonTW > wrote:
> If your 95 is anything like my 93, this job is tough. The toughest part by > far is getting the driveshaft removed. The bolts are very small (10 mm?) > and are loctited on. The small clearance means lots of turns of the wrench. I was under my 95 last night working on taking off the exhaust which was a slow process of applying liquid wrench and working the bolts. I finally got them off without breaking anything. I was looking at the drive shaft bolts and it appears a 12 pt 10mm socket will take these off. The 12 points will fit over the star pattern. Is this the correct tool? I was not able to get the shift lever off. The manual says to remove the bolt and lift the handle straight out. I removed a nut from a bolt which appears to go through the handle from the back and is keyed. However, the bolt does not budge. It looks to me like the bolt should back out without screwing. What am I missing? My son was playing in the mountains when he fried the clutch on a steep hill. I told him the only way this car was going again was after he and I fixed it. This is his car now. Thanks, Mark |
#4
|
|||
|
|||
Clutch Replacement
"Mark Barrett" > wrote in message > I was under my 95 last night working on taking off the exhaust > which was a slow process of applying liquid wrench and working the > bolts. I finally got them off without breaking anything. > > I was looking at the drive shaft bolts and it appears a 12 pt 10mm > socket will take these off. The 12 points will fit over the star > pattern. Is this the correct tool? > I wasn't able to get a rachet into the tight spaces. If you can, that would be great. > I was not able to get the shift lever off. The manual says to > remove the bolt and lift the handle straight out. I removed a nut > from a bolt which appears to go through the handle from the back > and is keyed. However, the bolt does not budge. It looks to me > like the bolt should back out without screwing. What am I missing? I don't remember any problem getting the shifter off. Yes, maybe you have to kind of force it off after loosening the bolt. I just don't remember. Everything other than the driveline bolts seemed pretty standard maintenance. > > My son was playing in the mountains when he fried the clutch on > a steep hill. I told him the only way this car was going again was > after he and I fixed it. This is his car now. > > Thanks, > Mark > |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Fan Clutch Replacement? | Kyonn Gowans | Jeep | 4 | June 6th 05 10:04 PM |
What now?? (Clutch slave again) | Eric | Jeep | 11 | May 29th 05 06:38 AM |
Wrong Clutch Fork? | Michael White | Jeep | 6 | February 8th 05 02:33 AM |
Clutch died on '96 Golf 1.8 | Wakeley Purple | VW water cooled | 12 | October 21st 04 10:31 AM |
93 SL2 clutch replacement | Trace | Saturn | 1 | May 11th 04 10:34 PM |