For you tool lovers(OT)

Stolen from the Harley group...subsitute "Jeep" for any mention of
motorcycles...



DRILL PRESS: A tall upright machine useful for suddenly snatching
flat metal bar stock out of your hands so that it smacks you in the
chest and flings your beer across the room, splattering it against
that freshly painted motorcycle part you were drying.


WIRE WHEEL: Cleans paint off bolts and then throws them somewhere
under the workbench with the speed of light. Also removes fingerprint
whorls and hard-earned guitar calluses in about the time it takes you
to say, "Ouch...."


ELECTRIC HAND DRILL: Normally used for spinning pop rivets in their
holes until you die of old age.


PLIERS: Used to round off bolt heads.


HACKSAW: One of a family of cutting tools built on the Ouija board
principle. It transforms human energy into a crooked, unpredictable
motion, and the more you attempt to influence its course, the more
dismal your future becomes.


VISE-GRIPS: Used to round off bolt heads. If nothing else is
available, they can also be used to transfer intense welding heat to
the palm of your hand.


OXYACETYLENE TORCH: Used almost entirely for lighting various
flammable objects in your shop on fire. Also handy for igniting the
grease inside the wheel hub you want the bearing race out of.


WHITWORTH SOCKETS: Once used for working on older British cars
and motorcycles, they are now used mainly for impersonating
that 9/16 or 1/2 socket you've been searching for the last 15 minutes.


HYDRAULIC FLOOR JACK: Used for lowering an automobile to the ground
after you have installed your new disk brake pads, trapping the jack
handle firmly under the bumper.


EIGHT-FOOT LONG DOUGLAS FIR 2X4: Used for levering an
automobile upward off a hydraulic jack handle.


TWEEZERS: A tool for removing wood splinters.


PHONE: Tool for calling your neighbors to see if he has another
hydraulic floor jack.


SNAP-ON GASKET SCRAPER: Theoretically useful as a sandwich tool for
spreading mayonnaise; used mainly for getting dog **** off your boot.


E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any
known drill bit that snaps off in bolt holes you couldn't use anyway.


TWO-TON ENGINE HOIST: A tool for testing the tensile strength
on everything you forgot to disconnect.


CRAFTSMAN 1/2 x 16-I NCH SCREWDRIVER: A large prybar that
inexplicably has an accurately machined screwdriver tip on the end
opposite the handle.


AVIATION METAL SNIPS: See hacksaw.


TROUBLE LIGHT: The home mechanic's own tanning booth. Sometimes
called a drop light, it is a good source of vitamin D, "the
sunshine vitamin," which is not otherwise found under cars at night.
Health benefits aside, it's main purpose is to consume 40-watt light
bulbs at about the same rate that 105-mm howitzer shells might be
used during, say, the first few hours of the Battle of the Bulge.
More often dark than light, its name is somewhat misleading.


PHILLIPS SCREWDRIVER: Normally used to stab the lids of old-style
paper-and-tin oil cans and splash oil on your shirt; but can
also be used, as the name implies, to strip out Phillips screw heads.


AIR COMPRESSOR: A machine that takes energy produced in a
coal-burning power plant 200 miles away and transforms it into
compressed air that travels by hose to a Chicago Pneumatic
impact wrench that grips rusty bolts last over tightened 58 years
ago by someone at H-D, and neatly rounds off their heads.


PRY BAR: A tool used to crumple the metal surrounding that clip or
bracket you needed to remove in order to replace a 50¢ part.


HOSE CUTTER: A tool used to cut hoses too short.


HAMMER: Originally employed as a weapon of war, the hammer nowadays
is used as a kind of divining rod to locate the most expensive
parts not far from the object we are trying to hit.


MECHANIC'S KNIFE: Used to open and slice through the contents
of cardboard cartons delivered to your front door; works particularly
well on contents such as seats, vinyl records, liquids in plastic
bottles, collector magazines, refund checks, and rubber or plastic
parts.


DAMMIT TOOL: Any handy tool that you grab and throw across the
garage while yelling "DAMMIT" at the top of your lungs. It is also the
next tool that you will need.


EXPLETIVE: A balm, usually applied verbally in hindsight, which
somehow eases those pains and indignities following our every
deficiency in foresight.


--
Old Crow
'82 FLTC-P "Pearl"
'95 Wrangler YJ
TOMKATAC, SENS, BS#133, MAMBM, SLOB#13, DH#2

ROTFPMP

Snow...

"Old Crow" > wrote in message
oups.com...

Stolen from the Harley group...subsitute "Jeep" for any mention of
motorcycles...



DRILL PRESS: A tall upright machine useful for suddenly snatching
flat metal bar stock out of your hands so that it smacks you in the
chest and flings your beer across the room, splattering it against
that freshly painted motorcycle part you were drying.


WIRE WHEEL: Cleans paint off bolts and then throws them somewhere
under the workbench with the speed of light. Also removes fingerprint
whorls and hard-earned guitar calluses in about the time it takes you
to say, "Ouch...."


ELECTRIC HAND DRILL: Normally used for spinning pop rivets in their
holes until you die of old age.


PLIERS: Used to round off bolt heads.


HACKSAW: One of a family of cutting tools built on the Ouija board
principle. It transforms human energy into a crooked, unpredictable
motion, and the more you attempt to influence its course, the more
dismal your future becomes.


VISE-GRIPS: Used to round off bolt heads. If nothing else is
available, they can also be used to transfer intense welding heat to
the palm of your hand.


OXYACETYLENE TORCH: Used almost entirely for lighting various
flammable objects in your shop on fire. Also handy for igniting the
grease inside the wheel hub you want the bearing race out of.


WHITWORTH SOCKETS: Once used for working on older British cars
and motorcycles, they are now used mainly for impersonating
that 9/16 or 1/2 socket you've been searching for the last 15 minutes.


HYDRAULIC FLOOR JACK: Used for lowering an automobile to the ground
after you have installed your new disk brake pads, trapping the jack
handle firmly under the bumper.


EIGHT-FOOT LONG DOUGLAS FIR 2X4: Used for levering an
automobile upward off a hydraulic jack handle.


TWEEZERS: A tool for removing wood splinters.


PHONE: Tool for calling your neighbors to see if he has another
hydraulic floor jack.


SNAP-ON GASKET SCRAPER: Theoretically useful as a sandwich tool for
spreading mayonnaise; used mainly for getting dog **** off your boot.


E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any
known drill bit that snaps off in bolt holes you couldn't use anyway.


TWO-TON ENGINE HOIST: A tool for testing the tensile strength
on everything you forgot to disconnect.


CRAFTSMAN 1/2 x 16-I NCH SCREWDRIVER: A large prybar that
inexplicably has an accurately machined screwdriver tip on the end
opposite the handle.


AVIATION METAL SNIPS: See hacksaw.


TROUBLE LIGHT: The home mechanic's own tanning booth. Sometimes
called a drop light, it is a good source of vitamin D, "the
sunshine vitamin," which is not otherwise found under cars at night.
Health benefits aside, it's main purpose is to consume 40-watt light
bulbs at about the same rate that 105-mm howitzer shells might be
used during, say, the first few hours of the Battle of the Bulge.
More often dark than light, its name is somewhat misleading.


PHILLIPS SCREWDRIVER: Normally used to stab the lids of old-style
paper-and-tin oil cans and splash oil on your shirt; but can
also be used, as the name implies, to strip out Phillips screw heads.


AIR COMPRESSOR: A machine that takes energy produced in a
coal-burning power plant 200 miles away and transforms it into
compressed air that travels by hose to a Chicago Pneumatic
impact wrench that grips rusty bolts last over tightened 58 years
ago by someone at H-D, and neatly rounds off their heads.


PRY BAR: A tool used to crumple the metal surrounding that clip or
bracket you needed to remove in order to replace a 50¢ part.


HOSE CUTTER: A tool used to cut hoses too short.


HAMMER: Originally employed as a weapon of war, the hammer nowadays
is used as a kind of divining rod to locate the most expensive
parts not far from the object we are trying to hit.


MECHANIC'S KNIFE: Used to open and slice through the contents
of cardboard cartons delivered to your front door; works particularly
well on contents such as seats, vinyl records, liquids in plastic
bottles, collector magazines, refund checks, and rubber or plastic
parts.


DAMMIT TOOL: Any handy tool that you grab and throw across the
garage while yelling "DAMMIT" at the top of your lungs. It is also the
next tool that you will need.


EXPLETIVE: A balm, usually applied verbally in hindsight, which
somehow eases those pains and indignities following our every
deficiency in foresight.


--
Old Crow
'82 FLTC-P "Pearl"
'95 Wrangler YJ
TOMKATAC, SENS, BS#133, MAMBM, SLOB#13, DH#2

That was a great laugh, thanks for sharing!

KJK


"Old Crow" > wrote in message
oups.com...

Stolen from the Harley group...subsitute "Jeep" for any mention of
motorcycles...



DRILL PRESS: A tall upright machine useful for suddenly snatching
flat metal bar stock out of your hands so that it smacks you in the
chest and flings your beer across the room, splattering it against
that freshly painted motorcycle part you were drying.


WIRE WHEEL: Cleans paint off bolts and then throws them somewhere
under the workbench with the speed of light. Also removes fingerprint
whorls and hard-earned guitar calluses in about the time it takes you
to say, "Ouch...."


ELECTRIC HAND DRILL: Normally used for spinning pop rivets in their
holes until you die of old age.


PLIERS: Used to round off bolt heads.


HACKSAW: One of a family of cutting tools built on the Ouija board
principle. It transforms human energy into a crooked, unpredictable
motion, and the more you attempt to influence its course, the more
dismal your future becomes.


VISE-GRIPS: Used to round off bolt heads. If nothing else is
available, they can also be used to transfer intense welding heat to
the palm of your hand.


OXYACETYLENE TORCH: Used almost entirely for lighting various
flammable objects in your shop on fire. Also handy for igniting the
grease inside the wheel hub you want the bearing race out of.


WHITWORTH SOCKETS: Once used for working on older British cars
and motorcycles, they are now used mainly for impersonating
that 9/16 or 1/2 socket you've been searching for the last 15 minutes.


HYDRAULIC FLOOR JACK: Used for lowering an automobile to the ground
after you have installed your new disk brake pads, trapping the jack
handle firmly under the bumper.


EIGHT-FOOT LONG DOUGLAS FIR 2X4: Used for levering an
automobile upward off a hydraulic jack handle.


TWEEZERS: A tool for removing wood splinters.


PHONE: Tool for calling your neighbors to see if he has another
hydraulic floor jack.


SNAP-ON GASKET SCRAPER: Theoretically useful as a sandwich tool for
spreading mayonnaise; used mainly for getting dog **** off your boot.


E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any
known drill bit that snaps off in bolt holes you couldn't use anyway.


TWO-TON ENGINE HOIST: A tool for testing the tensile strength
on everything you forgot to disconnect.


CRAFTSMAN 1/2 x 16-I NCH SCREWDRIVER: A large prybar that
inexplicably has an accurately machined screwdriver tip on the end
opposite the handle.


AVIATION METAL SNIPS: See hacksaw.


TROUBLE LIGHT: The home mechanic's own tanning booth. Sometimes
called a drop light, it is a good source of vitamin D, "the
sunshine vitamin," which is not otherwise found under cars at night.
Health benefits aside, it's main purpose is to consume 40-watt light
bulbs at about the same rate that 105-mm howitzer shells might be
used during, say, the first few hours of the Battle of the Bulge.
More often dark than light, its name is somewhat misleading.


PHILLIPS SCREWDRIVER: Normally used to stab the lids of old-style
paper-and-tin oil cans and splash oil on your shirt; but can
also be used, as the name implies, to strip out Phillips screw heads.


AIR COMPRESSOR: A machine that takes energy produced in a
coal-burning power plant 200 miles away and transforms it into
compressed air that travels by hose to a Chicago Pneumatic
impact wrench that grips rusty bolts last over tightened 58 years
ago by someone at H-D, and neatly rounds off their heads.


PRY BAR: A tool used to crumple the metal surrounding that clip or
bracket you needed to remove in order to replace a 50¢ part.


HOSE CUTTER: A tool used to cut hoses too short.


HAMMER: Originally employed as a weapon of war, the hammer nowadays
is used as a kind of divining rod to locate the most expensive
parts not far from the object we are trying to hit.


MECHANIC'S KNIFE: Used to open and slice through the contents
of cardboard cartons delivered to your front door; works particularly
well on contents such as seats, vinyl records, liquids in plastic
bottles, collector magazines, refund checks, and rubber or plastic
parts.


DAMMIT TOOL: Any handy tool that you grab and throw across the
garage while yelling "DAMMIT" at the top of your lungs. It is also the
next tool that you will need.


EXPLETIVE: A balm, usually applied verbally in hindsight, which
somehow eases those pains and indignities following our every
deficiency in foresight.


--
Old Crow
'82 FLTC-P "Pearl"
'95 Wrangler YJ
TOMKATAC, SENS, BS#133, MAMBM, SLOB#13, DH#2

Thanks Old Crow for the belly laugh.
As for myself I would add a cell phone at the end "to call for
assistance with mortal bleeding".

Who put the cameras in my shop! That was awesome. Thanks for sharing.


"Old Crow" > wrote in message
oups.com...

Stolen from the Harley group...subsitute "Jeep" for any mention of
motorcycles...



DRILL PRESS: A tall upright machine useful for suddenly snatching
flat metal bar stock out of your hands so that it smacks you in the
chest and flings your beer across the room, splattering it against
that freshly painted motorcycle part you were drying.


WIRE WHEEL: Cleans paint off bolts and then throws them somewhere
under the workbench with the speed of light. Also removes fingerprint
whorls and hard-earned guitar calluses in about the time it takes you
to say, "Ouch...."


ELECTRIC HAND DRILL: Normally used for spinning pop rivets in their
holes until you die of old age.


PLIERS: Used to round off bolt heads.


HACKSAW: One of a family of cutting tools built on the Ouija board
principle. It transforms human energy into a crooked, unpredictable
motion, and the more you attempt to influence its course, the more
dismal your future becomes.


VISE-GRIPS: Used to round off bolt heads. If nothing else is
available, they can also be used to transfer intense welding heat to
the palm of your hand.


OXYACETYLENE TORCH: Used almost entirely for lighting various
flammable objects in your shop on fire. Also handy for igniting the
grease inside the wheel hub you want the bearing race out of.


WHITWORTH SOCKETS: Once used for working on older British cars
and motorcycles, they are now used mainly for impersonating
that 9/16 or 1/2 socket you've been searching for the last 15 minutes.


HYDRAULIC FLOOR JACK: Used for lowering an automobile to the ground
after you have installed your new disk brake pads, trapping the jack
handle firmly under the bumper.


EIGHT-FOOT LONG DOUGLAS FIR 2X4: Used for levering an
automobile upward off a hydraulic jack handle.


TWEEZERS: A tool for removing wood splinters.


PHONE: Tool for calling your neighbors to see if he has another
hydraulic floor jack.


SNAP-ON GASKET SCRAPER: Theoretically useful as a sandwich tool for
spreading mayonnaise; used mainly for getting dog **** off your boot.


E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any
known drill bit that snaps off in bolt holes you couldn't use anyway.


TWO-TON ENGINE HOIST: A tool for testing the tensile strength
on everything you forgot to disconnect.


CRAFTSMAN 1/2 x 16-I NCH SCREWDRIVER: A large prybar that
inexplicably has an accurately machined screwdriver tip on the end
opposite the handle.


AVIATION METAL SNIPS: See hacksaw.


TROUBLE LIGHT: The home mechanic's own tanning booth. Sometimes
called a drop light, it is a good source of vitamin D, "the
sunshine vitamin," which is not otherwise found under cars at night.
Health benefits aside, it's main purpose is to consume 40-watt light
bulbs at about the same rate that 105-mm howitzer shells might be
used during, say, the first few hours of the Battle of the Bulge.
More often dark than light, its name is somewhat misleading.


PHILLIPS SCREWDRIVER: Normally used to stab the lids of old-style
paper-and-tin oil cans and splash oil on your shirt; but can
also be used, as the name implies, to strip out Phillips screw heads.


AIR COMPRESSOR: A machine that takes energy produced in a
coal-burning power plant 200 miles away and transforms it into
compressed air that travels by hose to a Chicago Pneumatic
impact wrench that grips rusty bolts last over tightened 58 years
ago by someone at H-D, and neatly rounds off their heads.


PRY BAR: A tool used to crumple the metal surrounding that clip or
bracket you needed to remove in order to replace a 50¢ part.


HOSE CUTTER: A tool used to cut hoses too short.


HAMMER: Originally employed as a weapon of war, the hammer nowadays
is used as a kind of divining rod to locate the most expensive
parts not far from the object we are trying to hit.


MECHANIC'S KNIFE: Used to open and slice through the contents
of cardboard cartons delivered to your front door; works particularly
well on contents such as seats, vinyl records, liquids in plastic
bottles, collector magazines, refund checks, and rubber or plastic
parts.


DAMMIT TOOL: Any handy tool that you grab and throw across the
garage while yelling "DAMMIT" at the top of your lungs. It is also the
next tool that you will need.


EXPLETIVE: A balm, usually applied verbally in hindsight, which
somehow eases those pains and indignities following our every
deficiency in foresight.


--
Old Crow
'82 FLTC-P "Pearl"
'95 Wrangler YJ
TOMKATAC, SENS, BS#133, MAMBM, SLOB#13, DH#2

I like this post...
Tomes

"Old Crow" > wrote in message
oups.com...

Stolen from the Harley group...subsitute "Jeep" for any mention of
motorcycles...



DRILL PRESS: A tall upright machine useful for suddenly snatching
flat metal bar stock out of your hands so that it smacks you in the
chest and flings your beer across the room, splattering it against
that freshly painted motorcycle part you were drying.


WIRE WHEEL: Cleans paint off bolts and then throws them somewhere
under the workbench with the speed of light. Also removes fingerprint
whorls and hard-earned guitar calluses in about the time it takes you
to say, "Ouch...."


ELECTRIC HAND DRILL: Normally used for spinning pop rivets in their
holes until you die of old age.


PLIERS: Used to round off bolt heads.


HACKSAW: One of a family of cutting tools built on the Ouija board
principle. It transforms human energy into a crooked, unpredictable
motion, and the more you attempt to influence its course, the more
dismal your future becomes.


VISE-GRIPS: Used to round off bolt heads. If nothing else is
available, they can also be used to transfer intense welding heat to
the palm of your hand.


OXYACETYLENE TORCH: Used almost entirely for lighting various
flammable objects in your shop on fire. Also handy for igniting the
grease inside the wheel hub you want the bearing race out of.


WHITWORTH SOCKETS: Once used for working on older British cars
and motorcycles, they are now used mainly for impersonating
that 9/16 or 1/2 socket you've been searching for the last 15 minutes.


HYDRAULIC FLOOR JACK: Used for lowering an automobile to the ground
after you have installed your new disk brake pads, trapping the jack
handle firmly under the bumper.


EIGHT-FOOT LONG DOUGLAS FIR 2X4: Used for levering an
automobile upward off a hydraulic jack handle.


TWEEZERS: A tool for removing wood splinters.


PHONE: Tool for calling your neighbors to see if he has another
hydraulic floor jack.


SNAP-ON GASKET SCRAPER: Theoretically useful as a sandwich tool for
spreading mayonnaise; used mainly for getting dog **** off your boot.


E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any
known drill bit that snaps off in bolt holes you couldn't use anyway.


TWO-TON ENGINE HOIST: A tool for testing the tensile strength
on everything you forgot to disconnect.


CRAFTSMAN 1/2 x 16-I NCH SCREWDRIVER: A large prybar that
inexplicably has an accurately machined screwdriver tip on the end
opposite the handle.


AVIATION METAL SNIPS: See hacksaw.


TROUBLE LIGHT: The home mechanic's own tanning booth. Sometimes
called a drop light, it is a good source of vitamin D, "the
sunshine vitamin," which is not otherwise found under cars at night.
Health benefits aside, it's main purpose is to consume 40-watt light
bulbs at about the same rate that 105-mm howitzer shells might be
used during, say, the first few hours of the Battle of the Bulge.
More often dark than light, its name is somewhat misleading.


PHILLIPS SCREWDRIVER: Normally used to stab the lids of old-style
paper-and-tin oil cans and splash oil on your shirt; but can
also be used, as the name implies, to strip out Phillips screw heads.


AIR COMPRESSOR: A machine that takes energy produced in a
coal-burning power plant 200 miles away and transforms it into
compressed air that travels by hose to a Chicago Pneumatic
impact wrench that grips rusty bolts last over tightened 58 years
ago by someone at H-D, and neatly rounds off their heads.


PRY BAR: A tool used to crumple the metal surrounding that clip or
bracket you needed to remove in order to replace a 50¢ part.


HOSE CUTTER: A tool used to cut hoses too short.


HAMMER: Originally employed as a weapon of war, the hammer nowadays
is used as a kind of divining rod to locate the most expensive
parts not far from the object we are trying to hit.


MECHANIC'S KNIFE: Used to open and slice through the contents
of cardboard cartons delivered to your front door; works particularly
well on contents such as seats, vinyl records, liquids in plastic
bottles, collector magazines, refund checks, and rubber or plastic
parts.


DAMMIT TOOL: Any handy tool that you grab and throw across the
garage while yelling "DAMMIT" at the top of your lungs. It is also the
next tool that you will need.


EXPLETIVE: A balm, usually applied verbally in hindsight, which
somehow eases those pains and indignities following our every
deficiency in foresight.


--
Old Crow
'82 FLTC-P "Pearl"
'95 Wrangler YJ
TOMKATAC, SENS, BS#133, MAMBM, SLOB#13, DH#2

popeyeball wrote:
> Thanks Old Crow for the belly laugh.
> As for myself I would add a cell phone at the end "to call for
> assistance with mortal bleeding".

Heh, I saw a guy on a Gold Wing last weekend using a phone that might
qualify for the list. Crusing through the parking lot, one hand on the
handlebars, other holding the phone to his ear...under his helmet!

--
Old Crow
'82 FLTC-P "Pearl"
'95 Wrangler YJ
TOMKAT,DOF#51,SENS, BS#133, MAMBM, SLOB#13, DH#2

ROTFPMP ???????? (roll on the floor pulling my pecker)???? lmao

Jeff








"Snow" > wrote in message
...
> ROTFPMP
>
> Snow...
>
> "Old Crow" > wrote in message
> oups.com...
>
> Stolen from the Harley group...subsitute "Jeep" for any mention of
> motorcycles...
>
>
>
> DRILL PRESS: A tall upright machine useful for suddenly snatching
> flat metal bar stock out of your hands so that it smacks you in the
> chest and flings your beer across the room, splattering it against
> that freshly painted motorcycle part you were drying.
>
>
> WIRE WHEEL: Cleans paint off bolts and then throws them somewhere
> under the workbench with the speed of light. Also removes fingerprint
> whorls and hard-earned guitar calluses in about the time it takes you
> to say, "Ouch...."
>
>
> ELECTRIC HAND DRILL: Normally used for spinning pop rivets in their
> holes until you die of old age.
>
>
> PLIERS: Used to round off bolt heads.
>
>
> HACKSAW: One of a family of cutting tools built on the Ouija board
> principle. It transforms human energy into a crooked, unpredictable
> motion, and the more you attempt to influence its course, the more
> dismal your future becomes.
>
>
> VISE-GRIPS: Used to round off bolt heads. If nothing else is
> available, they can also be used to transfer intense welding heat to
> the palm of your hand.
>
>
> OXYACETYLENE TORCH: Used almost entirely for lighting various
> flammable objects in your shop on fire. Also handy for igniting the
> grease inside the wheel hub you want the bearing race out of.
>
>
> WHITWORTH SOCKETS: Once used for working on older British cars
> and motorcycles, they are now used mainly for impersonating
> that 9/16 or 1/2 socket you've been searching for the last 15 minutes.
>
>
> HYDRAULIC FLOOR JACK: Used for lowering an automobile to the ground
> after you have installed your new disk brake pads, trapping the jack
> handle firmly under the bumper.
>
>
> EIGHT-FOOT LONG DOUGLAS FIR 2X4: Used for levering an
> automobile upward off a hydraulic jack handle.
>
>
> TWEEZERS: A tool for removing wood splinters.
>
>
> PHONE: Tool for calling your neighbors to see if he has another
> hydraulic floor jack.
>
>
> SNAP-ON GASKET SCRAPER: Theoretically useful as a sandwich tool for
> spreading mayonnaise; used mainly for getting dog **** off your boot.
>
>
> E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any
> known drill bit that snaps off in bolt holes you couldn't use anyway.
>
>
> TWO-TON ENGINE HOIST: A tool for testing the tensile strength
> on everything you forgot to disconnect.
>
>
> CRAFTSMAN 1/2 x 16-I NCH SCREWDRIVER: A large prybar that
> inexplicably has an accurately machined screwdriver tip on the end
> opposite the handle.
>
>
> AVIATION METAL SNIPS: See hacksaw.
>
>
> TROUBLE LIGHT: The home mechanic's own tanning booth. Sometimes
> called a drop light, it is a good source of vitamin D, "the
> sunshine vitamin," which is not otherwise found under cars at night.
> Health benefits aside, it's main purpose is to consume 40-watt light
> bulbs at about the same rate that 105-mm howitzer shells might be
> used during, say, the first few hours of the Battle of the Bulge.
> More often dark than light, its name is somewhat misleading.
>
>
> PHILLIPS SCREWDRIVER: Normally used to stab the lids of old-style
> paper-and-tin oil cans and splash oil on your shirt; but can
> also be used, as the name implies, to strip out Phillips screw heads.
>
>
> AIR COMPRESSOR: A machine that takes energy produced in a
> coal-burning power plant 200 miles away and transforms it into
> compressed air that travels by hose to a Chicago Pneumatic
> impact wrench that grips rusty bolts last over tightened 58 years
> ago by someone at H-D, and neatly rounds off their heads.
>
>
> PRY BAR: A tool used to crumple the metal surrounding that clip or
> bracket you needed to remove in order to replace a 50¢ part.
>
>
> HOSE CUTTER: A tool used to cut hoses too short.
>
>
> HAMMER: Originally employed as a weapon of war, the hammer nowadays
> is used as a kind of divining rod to locate the most expensive
> parts not far from the object we are trying to hit.
>
>
> MECHANIC'S KNIFE: Used to open and slice through the contents
> of cardboard cartons delivered to your front door; works particularly
> well on contents such as seats, vinyl records, liquids in plastic
> bottles, collector magazines, refund checks, and rubber or plastic
> parts.
>
>
> DAMMIT TOOL: Any handy tool that you grab and throw across the
> garage while yelling "DAMMIT" at the top of your lungs. It is also the
> next tool that you will need.
>
>
> EXPLETIVE: A balm, usually applied verbally in hindsight, which
> somehow eases those pains and indignities following our every
> deficiency in foresight.
>
>
> --
> Old Crow
> '82 FLTC-P "Pearl"
> '95 Wrangler YJ
> TOMKATAC, SENS, BS#133, MAMBM, SLOB#13, DH#2
>
>

4X4PLAY wrote:
> ROTFPMP ???????? (roll on the floor pulling my pecker)???? lmao
>
> Jeff

Wax on...Wax off?




--
Old Crow
'82 FLTC-P "Pearl"
'95 Wrangler YJ
TOMKAT,DOF#51,SENS, BS#133, MAMBM, SLOB#13, DH#2

"4X4PLAY" > wrote in message
news:rlHcf.106167$y_1.41603@edtnps89...
: ROTFPMP ???????? (roll on the floor pulling my pecker)???? lmao
:
: Jeff


I'll bet it was "peeing my pants'
if you keep pullin on that thang, you're gonna stretch it all out and then
it will get wrinkly when it gets cold!


LOL

KJK

:
:
:
:
:
:
:
: "Snow" > wrote in message
: ...
: > ROTFPMP
: >
: > Snow...
: >
: > "Old Crow" > wrote in message
: > oups.com...
: >
: > Stolen from the Harley group...subsitute "Jeep" for any mention of
: > motorcycles...
: >
: >
: >
: > DRILL PRESS: A tall upright machine useful for suddenly snatching
: > flat metal bar stock out of your hands so that it smacks you in the
: > chest and flings your beer across the room, splattering it against
: > that freshly painted motorcycle part you were drying.
: >
: >
: > WIRE WHEEL: Cleans paint off bolts and then throws them somewhere
: > under the workbench with the speed of light. Also removes fingerprint
: > whorls and hard-earned guitar calluses in about the time it takes you
: > to say, "Ouch...."
: >
: >
: > ELECTRIC HAND DRILL: Normally used for spinning pop rivets in their
: > holes until you die of old age.
: >
: >
: > PLIERS: Used to round off bolt heads.
: >
: >
: > HACKSAW: One of a family of cutting tools built on the Ouija board
: > principle. It transforms human energy into a crooked, unpredictable
: > motion, and the more you attempt to influence its course, the more
: > dismal your future becomes.
: >
: >
: > VISE-GRIPS: Used to round off bolt heads. If nothing else is
: > available, they can also be used to transfer intense welding heat to
: > the palm of your hand.
: >
: >
: > OXYACETYLENE TORCH: Used almost entirely for lighting various
: > flammable objects in your shop on fire. Also handy for igniting the
: > grease inside the wheel hub you want the bearing race out of.
: >
: >
: > WHITWORTH SOCKETS: Once used for working on older British cars
: > and motorcycles, they are now used mainly for impersonating
: > that 9/16 or 1/2 socket you've been searching for the last 15 minutes.
: >
: >
: > HYDRAULIC FLOOR JACK: Used for lowering an automobile to the ground
: > after you have installed your new disk brake pads, trapping the jack
: > handle firmly under the bumper.
: >
: >
: > EIGHT-FOOT LONG DOUGLAS FIR 2X4: Used for levering an
: > automobile upward off a hydraulic jack handle.
: >
: >
: > TWEEZERS: A tool for removing wood splinters.
: >
: >
: > PHONE: Tool for calling your neighbors to see if he has another
: > hydraulic floor jack.
: >
: >
: > SNAP-ON GASKET SCRAPER: Theoretically useful as a sandwich tool for
: > spreading mayonnaise; used mainly for getting dog **** off your boot.
: >
: >
: > E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any
: > known drill bit that snaps off in bolt holes you couldn't use anyway.
: >
: >
: > TWO-TON ENGINE HOIST: A tool for testing the tensile strength
: > on everything you forgot to disconnect.
: >
: >
: > CRAFTSMAN 1/2 x 16-I NCH SCREWDRIVER: A large prybar that
: > inexplicably has an accurately machined screwdriver tip on the end
: > opposite the handle.
: >
: >
: > AVIATION METAL SNIPS: See hacksaw.
: >
: >
: > TROUBLE LIGHT: The home mechanic's own tanning booth. Sometimes
: > called a drop light, it is a good source of vitamin D, "the
: > sunshine vitamin," which is not otherwise found under cars at night.
: > Health benefits aside, it's main purpose is to consume 40-watt light
: > bulbs at about the same rate that 105-mm howitzer shells might be
: > used during, say, the first few hours of the Battle of the Bulge.
: > More often dark than light, its name is somewhat misleading.
: >
: >
: > PHILLIPS SCREWDRIVER: Normally used to stab the lids of old-style
: > paper-and-tin oil cans and splash oil on your shirt; but can
: > also be used, as the name implies, to strip out Phillips screw heads.
: >
: >
: > AIR COMPRESSOR: A machine that takes energy produced in a
: > coal-burning power plant 200 miles away and transforms it into
: > compressed air that travels by hose to a Chicago Pneumatic
: > impact wrench that grips rusty bolts last over tightened 58 years
: > ago by someone at H-D, and neatly rounds off their heads.
: >
: >
: > PRY BAR: A tool used to crumple the metal surrounding that clip or
: > bracket you needed to remove in order to replace a 50¢ part.
: >
: >
: > HOSE CUTTER: A tool used to cut hoses too short.
: >
: >
: > HAMMER: Originally employed as a weapon of war, the hammer nowadays
: > is used as a kind of divining rod to locate the most expensive
: > parts not far from the object we are trying to hit.
: >
: >
: > MECHANIC'S KNIFE: Used to open and slice through the contents
: > of cardboard cartons delivered to your front door; works particularly
: > well on contents such as seats, vinyl records, liquids in plastic
: > bottles, collector magazines, refund checks, and rubber or plastic
: > parts.
: >
: >
: > DAMMIT TOOL: Any handy tool that you grab and throw across the
: > garage while yelling "DAMMIT" at the top of your lungs. It is also the
: > next tool that you will need.
: >
: >
: > EXPLETIVE: A balm, usually applied verbally in hindsight, which
: > somehow eases those pains and indignities following our every
: > deficiency in foresight.
: >
: >
: > --
: > Old Crow
: > '82 FLTC-P "Pearl"
: > '95 Wrangler YJ
: > TOMKATAC, SENS, BS#133, MAMBM, SLOB#13, DH#2
: >
: >
:
: