|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
April 30th 04, 05:25 AM
|
|||
|
|||
what kind of sheet metal to order?
what type (alloy?) or number should I order for panel work on a jeep?
Local sheet metal shop asked my what kind of steel I needed. 'Autobody' was not an option. Thanks 
|
| Ads |
|
#2
April 30th 04, 05:16 PM
|
|||
|
|||
|
Paul Farber wrote:
> > what type (alloy?) or number should I order for panel work on a jeep? > > Local sheet metal shop asked my what kind of steel I needed. 'Autobody' was > not an option. What options did they give you? Did you ask them for their recommendation? You can find descriptions of some common steel allys he http://www.mcmaster.com/param/asp/ps...sc=Alloy+Steel -- Roger
|
|
#3
April 30th 04, 05:16 PM
|
|||
|
|||
|
Paul Farber wrote:
> > what type (alloy?) or number should I order for panel work on a jeep? > > Local sheet metal shop asked my what kind of steel I needed. 'Autobody' was > not an option. What options did they give you? Did you ask them for their recommendation? You can find descriptions of some common steel allys he http://www.mcmaster.com/param/asp/ps...sc=Alloy+Steel -- Roger
|
|
#4
April 30th 04, 05:17 PM
|
|||
|
|||
|
Paul Farber wrote:
> > what type (alloy?) or number should I order for panel work on a jeep? > > Local sheet metal shop asked my what kind of steel I needed. 'Autobody' was > not an option. What options did they give you? Did you ask them for their recommendation? You can find descriptions of some common steel allys he http://www.mcmaster.com/param/asp/ps...sc=Alloy+Steel -- Roger
|
|
#5
April 30th 04, 05:17 PM
|
|||
|
|||
|
Paul Farber wrote:
> > what type (alloy?) or number should I order for panel work on a jeep? > > Local sheet metal shop asked my what kind of steel I needed. 'Autobody' was > not an option. What options did they give you? Did you ask them for their recommendation? You can find descriptions of some common steel allys he http://www.mcmaster.com/param/asp/ps...sc=Alloy+Steel -- Roger
|
|
#6
May 3rd 04, 08:11 PM
|
|||
|
|||
|
10 gauge
H "Paul Farber" > wrote in message ... > what type (alloy?) or number should I order for panel work on a jeep? > > Local sheet metal shop asked my what kind of steel I needed. 'Autobody' was > not an option. > > Thanks > >
|
|
#7
May 3rd 04, 08:11 PM
|
|||
|
|||
|
10 gauge
H "Paul Farber" > wrote in message ... > what type (alloy?) or number should I order for panel work on a jeep? > > Local sheet metal shop asked my what kind of steel I needed. 'Autobody' was > not an option. > > Thanks > >
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| FS: "Corvette Evolution 1953-1986" Litho Sheet | J.R. Sinclair | Corvette | 0 | December 29th 04 01:11 PM |
| FS: "Corvette Evolution 1953-1986" Litho Sheet | J.R. Sinclair | Corvette | 0 | August 11th 04 07:30 AM |
Linear Mode
