If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Stupid OEM bikini question
I bought a used OEM bikini, windjammer, tonneau combo off a 97 (says "Jeep"
on the tags, so I'm assuming its OEM). The header is a two piece, screw on flat aluminum arrangement with a round channel for the front of the top. Because the aluminum is brite, I assume the top must fold back over it in some fashion. Now where does this thing bolt on? On my CJ it bolted down on top of the windshield, slot forward. The Bestop site shows their channel bolted to the inside of the windshield slot up (seems that that would rip off at highway speeds). The guy I got it from said "when i got it installed on my jeep they installed it outside just above my window but its suppose 2 be installed inside ontop of the rubber where your hard top sits", which I'm having a hard time picturing... I'm at a loss. I can't seem to locate anything specific for this unit and the local dealers are not very helpful. Does anyone have one and know how it was originally intended to go on? Its still dead of winter here so I can't go play on the TJ but I want to get everything together for those first rays of hope... Thanx in advance for any pointers... -- (Please remove the "nospam" when replying) 2000 TJ - OME, 31x10,and a lot of wishfull thinking |
Ads |
#2
|
|||
|
|||
"EDITED FOR CONTENT Hooligan" > ASKED" >I bought a used OEM bikini, Does anyone have one and know how it was >originally intended to go on? > Thanx in advance for any pointers... Well first off is it a bikini or a thong? second, I hope you bought it for someone of the female gender to wear, not yourself. as for the fit and installation ... this seems like a very informative site http://www.biniki-fashions.com/wearing_biniki.htm Snow ... "smartass Saturdays" lol |
#3
|
|||
|
|||
You did NOT buy an OEM bikini. There is no such thing. Any bikini you found
is aftermarket. "Hooligan" > wrote in message ... >I bought a used OEM bikini, windjammer, tonneau combo off a 97 (says "Jeep" >on the tags, so I'm assuming its OEM). The header is a two piece, screw on >flat aluminum arrangement with a round channel for the front of the top. >Because the aluminum is brite, I assume the top must fold back over it in >some fashion. Now where does this thing bolt on? > > On my CJ it bolted down on top of the windshield, slot forward. The Bestop > site shows their channel bolted to the inside of the windshield slot up > (seems that that would rip off at highway speeds). The guy I got it from > said "when i got it installed on my jeep they installed it outside just > above my window but its suppose 2 be installed inside ontop of the rubber > where your hard top sits", which I'm having a hard time picturing... > > I'm at a loss. I can't seem to locate anything specific for this unit and > the local dealers are not very helpful. Does anyone have one and know how > it was originally intended to go on? > > Its still dead of winter here so I can't go play on the TJ but I want to > get everything together for those first rays of hope... > > Thanx in advance for any pointers... > > -- > > (Please remove the "nospam" when replying) > > 2000 TJ - OME, 31x10,and a lot of wishfull thinking > > > |
#4
|
|||
|
|||
http://www.bestop.com/installation_guides/52525.pdf
God Bless America, ßill O|||||||O http://www.billhughes.com/ Hooligan wrote: > > I bought a used OEM bikini, windjammer, tonneau combo off a 97 (says "Jeep" > on the tags, so I'm assuming its OEM). The header is a two piece, screw on > flat aluminum arrangement with a round channel for the front of the top. > Because the aluminum is brite, I assume the top must fold back over it in > some fashion. Now where does this thing bolt on? > > On my CJ it bolted down on top of the windshield, slot forward. The Bestop > site shows their channel bolted to the inside of the windshield slot up > (seems that that would rip off at highway speeds). The guy I got it from > said "when i got it installed on my jeep they installed it outside just > above my window but its suppose 2 be installed inside ontop of the rubber > where your hard top sits", which I'm having a hard time picturing... > > I'm at a loss. I can't seem to locate anything specific for this unit and > the local dealers are not very helpful. Does anyone have one and know how it > was originally intended to go on? > > Its still dead of winter here so I can't go play on the TJ but I want to get > everything together for those first rays of hope... > > Thanx in advance for any pointers... > > -- > > (Please remove the "nospam" when replying) > > 2000 TJ - OME, 31x10,and a lot of wishfull thinking |
#6
|
|||
|
|||
On Sat, 29 Jan 2005 20:22:07 GMT, "Hooligan"
> wrote: >Snow - Its polka dotted and teenie which is what is causing the trouble. > >Jeff - Guy said he got it from DC and the only tags on it say "JEEP" with >the trademark symbol (all three pieces). I assumed that would mean OEM but >hey... > >Bill - If it was the same unit as Bestop's site I would have no questions. >It isn't the same. > >I was just wondering if someone had the the same type of top and where it >was designed to go. > >Thanx anyway... My kid's got one with aa OEM Jeep tag on it also. I got it for him from a Jeep that was traded in where I work. He had to go to the dealer and get the channel, as it wasn't on the Jeep I got the top out of. The channel mounts to the inside of the window frame with a bunch of sheet metal screws, and is different from the header that is part of the soft top. I'd describe it better, but he did the install, and the Jeep's about 70 miles from here, so I can't just go out and look at it. -- Old Crow '82 Shovelhead FLTC 92" 'Pearl' '95 Jeep Wrangler YJ TOMKAT, BS#133, SENS, MAMBM, DOF#51, SPUNGER#2 |
#7
|
|||
|
|||
"Hooligan" > wrote in message ... > Snow - Its polka dotted and teenie which is what is causing the trouble. > > Jeff - Guy said he got it from DC and the only tags on it say "JEEP" with > the trademark symbol (all three pieces). I assumed that would mean OEM but > hey... > I was not aware that there was an OEM bikini. DC gets its top from Bestop, and it is certainly possible that Bestop might have made a bikini that it sold through Jeep, or sold and Jeep allowed them to put the logo on. I guess the bottom line is, how do you install the header? |
#8
|
|||
|
|||
And thats the part I don't know. The header is 2 pieces of brite aluminim
with a round channel for the leading edge of the top. Sort of shaped like this when looked at end on: _____(_) The flat section has no cutouts like the pictures on the Bestop site to get around the footman loop, ST/HT clamps, etc. The channel does have a small lip on the bottom of both the forward and trailing lengthwise edge. Almost like it should fit over something. If you bolted it to something flat it would bow in in the center. What started this was that I bought it via email and I wanted to make sure that I got the proper gear from the sale while it was fresh. Not try and fix a problem after several months when I can actually get it on... The canvas parts looks band new, but the the channel didn't look like anything I had seen or could find. The DC dealerships here in Sait John just looked blank. I guess I will have to wait until I can lift the HT and experiment. The hazards of buying summer gear in the dead of winter I guess... -- (Please remove the "nospam" when replying) 2000 TJ - OME, 31x10,and a lot of wishfull thinking "Jeff Strickland" > wrote in message news > > "Hooligan" > wrote in message > ... >> Snow - Its polka dotted and teenie which is what is causing the trouble. >> >> Jeff - Guy said he got it from DC and the only tags on it say "JEEP" with >> the trademark symbol (all three pieces). I assumed that would mean OEM >> but hey... >> > > I was not aware that there was an OEM bikini. DC gets its top from Bestop, > and it is certainly possible that Bestop might have made a bikini that it > sold through Jeep, or sold and Jeep allowed them to put the logo on. > > I guess the bottom line is, how do you install the header? > > > > > > |
#9
|
|||
|
|||
Hooligan wrote:
> And thats the part I don't know. The header is 2 pieces of brite aluminim > with a round channel for the leading edge of the top. Sort of shaped like > this when looked at end on: > > _____(_) > > The flat section has no cutouts like the pictures on the Bestop site to get > around the footman loop, ST/HT clamps, etc. The channel does have a small > lip on the bottom of both the forward and trailing lengthwise edge. Almost > like it should fit over something. If you bolted it to something flat it > would bow in in the center. > > What started this was that I bought it via email and I wanted to make sure > that I got the proper gear from the sale while it was fresh. Not try and fix > a problem after several months when I can actually get it on... The canvas > parts looks band new, but the the channel didn't look like anything I had > seen or could find. The DC dealerships here in Sait John just looked blank. > I guess I will have to wait until I can lift the HT and experiment. The > hazards of buying summer gear in the dead of winter I guess... > This is a link to Bestop's installation instructions. On my 2004 TJ with the Bikini top (Jeep logo label) the header is the same as the full soft top one. http://www.bestop.com/installation_guides/52525.pdf -- <o><><><><><><><><><><><o><><><><><><><o><><><><>< ><><><><><><><><o> http://www.texbiker.net -- Texas Bicycling Information Central. <o><><><><><><><><><><><o><><><><><><><o><><><><>< ><><><><><><><><o> ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==---- http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups ----= East and West-Coast Server Farms - Total Privacy via Encryption =---- |
#10
|
|||
|
|||
Tme out!
Have you investigated that you do not even need the new header? If you have a Jeep version of the Bestop bikini, it should take the standard Jeep soft top header connector. You shouldn't even need any additional hardware. Simply take the soft top off and put the bikini on. I have a Bestop soft top and a Bestop bikini for my CJ, and the header is the same for both. I do not need two different headers for the two different tops. "Hooligan" > wrote in message ... > And thats the part I don't know. The header is 2 pieces of brite aluminim > with a round channel for the leading edge of the top. Sort of shaped like > this when looked at end on: > > _____(_) > > The flat section has no cutouts like the pictures on the Bestop site to > get around the footman loop, ST/HT clamps, etc. The channel does have a > small lip on the bottom of both the forward and trailing lengthwise edge. > Almost like it should fit over something. If you bolted it to something > flat it would bow in in the center. > > What started this was that I bought it via email and I wanted to make sure > that I got the proper gear from the sale while it was fresh. Not try and > fix a problem after several months when I can actually get it on... The > canvas parts looks band new, but the the channel didn't look like anything > I had seen or could find. The DC dealerships here in Sait John just looked > blank. I guess I will have to wait until I can lift the HT and experiment. > The hazards of buying summer gear in the dead of winter I guess... > > -- > > (Please remove the "nospam" when replying) > > 2000 TJ - OME, 31x10,and a lot of wishfull thinking > > > "Jeff Strickland" > wrote in message > news >> >> "Hooligan" > wrote in message >> ... >>> Snow - Its polka dotted and teenie which is what is causing the trouble. >>> >>> Jeff - Guy said he got it from DC and the only tags on it say "JEEP" >>> with the trademark symbol (all three pieces). I assumed that would mean >>> OEM but hey... >>> >> >> I was not aware that there was an OEM bikini. DC gets its top from >> Bestop, and it is certainly possible that Bestop might have made a bikini >> that it sold through Jeep, or sold and Jeep allowed them to put the logo >> on. >> >> I guess the bottom line is, how do you install the header? >> >> >> >> >> >> > > |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Stupid question (was Changing the oil filter only) | Bill F | Technology | 20 | January 18th 05 10:57 PM |
Stupid question about tires | Robert P. | Saturn | 3 | September 9th 04 12:15 AM |
Stupid Question | BxP9 | Saturn | 1 | September 4th 04 02:00 PM |
stupid question | R.Reppy | Dodge | 6 | June 14th 04 09:39 PM |