If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
spark plug "holes" in valve cover full of oil!
I was going to do a compression test on this car (its a 95 saturn) and
two of the plug wires came out totally soaked in oil! The first two were just fine and I got a normal compression reading on the first cyl. The cylinders that are full of oil would not give a normal compression reading, they just shot my guage sky-high becuase of all the oil in the cyl. I suppose. This is the car that was had a radiator resevoir filled with the grey gunk. Could the oil in those last two "plug wire holes" just be from a poorly seal around the hole openings in the valve cover? I've never seen anything like this... The car still seems to run just fine even with two totally saturated plugs . Even the plugs themselves came out with oil all over them... supa |
Ads |
#2
|
|||
|
|||
spark plug "holes" in valve cover full of oil!
"supafly" > wrote in message oups.com... > I was going to do a compression test on this car (its a 95 saturn) and > two of the plug wires came out totally soaked in oil! The first two > were just fine and I got a normal compression reading on the first cyl. > The cylinders that are full of oil would not give a normal compression > reading, they just shot my guage sky-high becuase of all the oil in the > cyl. I suppose. > > This is the car that was had a radiator resevoir filled with the grey > gunk. Could the oil in those last two "plug wire holes" just be from a > poorly seal around the hole openings in the valve cover? I've never > seen anything like this... The car still seems to run just fine even > with two totally saturated plugs . Even the plugs themselves came out > with oil all over them... > Leaking valve guide seals I would guess. Ted |
#3
|
|||
|
|||
spark plug "holes" in valve cover full of oil!
Your story doesn't fly, supa.
If the plugs came out oil soaked, those cylinders were not firing and it could not have been running fine as you say. If it is running fine, you got the plugs soaked on the way out. And if you let a bunch of oil run into the cylinder you are dam lucky that you did not lock up a cylinder and bend a rod. What did you do with the gray gunk in the radiator situation? Did you bypass the cooler or replace the radiator to eliminate that possibility? Was the trans fluid contaminated with coolant? You leave too many unanswered questions and your testing technique is very suspect. If it runs fine and the contamination into the radiator is fixed, then fix the oil leak and drive it. |
#4
|
|||
|
|||
spark plug "holes" in valve cover full of oil!
"supafly" > wrote in message oups.com... >I was going to do a compression test on this car (its a 95 saturn) and > two of the plug wires came out totally soaked in oil! The first two > were just fine and I got a normal compression reading on the first cyl. > The cylinders that are full of oil would not give a normal compression > reading, they just shot my guage sky-high becuase of all the oil in the > cyl. I suppose. > > This is the car that was had a radiator resevoir filled with the grey > gunk. Could the oil in those last two "plug wire holes" just be from a > poorly seal around the hole openings in the valve cover? I've never > seen anything like this... The car still seems to run just fine even > with two totally saturated plugs . Even the plugs themselves came out > with oil all over them... > > supa > The spark plug tubes have a gasket on the top that seals against the valve cover to keep the oil out. These gaskets should be part of a valve cover gasket set, but sometimes they are sold seperately. Replacing the valve cover gasket and spark plug tube gaskets should stop your oil leak |
#5
|
|||
|
|||
spark plug "holes" in valve cover full of oil!
I think the OP is talking about oil pooling around the spark plug where
it runs through the valve cover. I had a old Dodge Slant-six that used to do that and my Toyota 3TC Hemi does it a little. What I would do with the Dodge is pull the wire off and use my compressor to blow out the oil, covering the hole with a rag and then pull the plug. Now that you have oil in the cyl. you may have to remove all the plugs and turn the engine over with the starter to blow out the oil that drained down into the cyl. Cover the holes with rags or you'll have oil all over everything. If you don't want this to happen again you need to replace the valve cover gasket AND the "O" rings/flat washer that seals around the spark plugs between head and valve cover. I don't think that your guage will give you good readings now that it has oil in it. HTH, Rick |
#6
|
|||
|
|||
spark plug "holes" in valve cover full of oil!
supafly > wrote:
> >This is the car that was had a radiator resevoir filled with the grey >gunk. Could the oil in those last two "plug wire holes" just be from a >poorly seal around the hole openings in the valve cover? I've never >seen anything like this... The car still seems to run just fine even >with two totally saturated plugs . Even the plugs themselves came out >with oil all over them... Right. Valve cover gaskets are bad. Probably a good idea to replace them before the plug wires fail from all the oil, and to keep oil from getting in the cylinders when you change plugs. --scott -- "C'est un Nagra. C'est suisse, et tres, tres precis." |
#7
|
|||
|
|||
spark plug "holes" in valve cover full of oil!
supafly wrote:
> > I was going to do a compression test on this car (its a 95 saturn) and > two of the plug wires came out totally soaked in oil! The first two > were just fine and I got a normal compression reading on the first cyl. > The cylinders that are full of oil would not give a normal compression > reading, they just shot my guage sky-high becuase of all the oil in the > cyl. I suppose. > > This is the car that was had a radiator resevoir filled with the grey > gunk. Could the oil in those last two "plug wire holes" just be from a > poorly seal around the hole openings in the valve cover? I've never > seen anything like this... The car still seems to run just fine even > with two totally saturated plugs . Even the plugs themselves came out > with oil all over them... > > supa Many vehicles have that problem, not just Saturn. The valve cover gasket is bad. Replace it. |
#8
|
|||
|
|||
spark plug "holes" in valve cover full of oil!
>I was going to do a compression test on this car (its a 95 Saturn) and
> two of the plug wires came out totally soaked in oil! The first two > were just fine and I got a normal compression reading on the first cyl. > The cylinders that are full of oil would not give a normal compression > reading, they just shot my guage sky-high because of all the oil in the > cyl. I suppose. Common Saturn problem. You need a new gasket kit. I believe mine was around $35 for the outer cover ring and the 4 little rings. When you see a kit, you'll think "Thirty-five dollars for that!" The gasket looks like it was squeezed out of a silicon chalk gun onto a piece of cardboard and then wrapped in kitchen-grade Handi-Wrap. Was an easy, but messy job. Make sure you got a torque wrench for the bolts. Might want to look and see if the upper engine hanger mount is shot as well while you're at it (another $85 or so with new bolts). Mine never leaked again up until the day I got rid of it (Dual-Cam model, fwiw). Couldn't say much about the Saturn's affinity to use oil though (especially the stick shift model). B~ |
#9
|
|||
|
|||
spark plug "holes" in valve cover full of oil!
"B. Peg" > wrote
> Common Saturn problem. You need a new gasket kit. I believe mine was > around $35 for the outer cover ring and the 4 little rings. > > When you see a kit, you'll think "Thirty-five dollars for that!" The gasket > looks like it was squeezed out of a silicon chalk gun onto a piece of > cardboard and then wrapped in kitchen-grade Handi-Wrap. You could try to mold your own out of silicone RTV. |
#10
|
|||
|
|||
spark plug "holes" in valve cover full of oil!
>> When you see a kit, you'll think "Thirty-five dollars for that!" The
>> gasket >> looks like it was squeezed out of a silicon chalk gun onto a piece of >> cardboard and then wrapped in kitchen-grade Handi-Wrap. > > You could try to mold your own out of silicone RTV. I believe you could do it yourself with a RTV in a chalking gun and maybe it would adhere better as well. It is pretty thick (maybe 1/4 inch in diameter). If I had the problem again, I would try it as the Saturn gasket set is pricey at best. B~ |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 5 | June 24th 05 05:27 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 5 | June 8th 05 05:28 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 5 | May 24th 05 05:27 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 5 | May 8th 05 05:29 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 10 | October 16th 04 05:28 AM |