If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
clicking noise on 99 VW Passat (6 Cyl) - only when clutch engaged
When I make a turn, of any radius, whith the clutch engaged, there is a
clicking noise coming from the front of the car. Going straight, there is no sound, and if I disengage the clutch, the noise disappears.... Any ideas? |
Ads |
#2
|
|||
|
|||
clicking noise on 99 VW Passat (6 Cyl) - only when clutch engaged
Sounds like CV joints. Check the condition of the boots, inner and outer
joints. I just got through doing 3 of the boots on a 2001 Passat V6 auto. It was clicking too. later, dave (One out of many daves) > wrote in message oups.com... > When I make a turn, of any radius, whith the clutch engaged, there is a > clicking noise coming from the front of the car. Going straight, there > is no sound, and if I disengage the clutch, the noise disappears.... > > Any ideas? > |
#3
|
|||
|
|||
clicking noise on 99 VW Passat (6 Cyl) - only when clutch engaged
If it ain't the CV joint, either one, could be the "throw out bearing"
preceeding the clutch, at the clutch fork. -- Jonny > wrote in message oups.com... > When I make a turn, of any radius, whith the clutch engaged, there is a > clicking noise coming from the front of the car. Going straight, there > is no sound, and if I disengage the clutch, the noise disappears.... > > Any ideas? > |
#4
|
|||
|
|||
clicking noise on 99 VW Passat (6 Cyl) - only when clutch engaged
Explain why it is only there on turns? If it's a clutch issue it would do it
regardless off which way the wheels are turned! "Jonny" > wrote in message link.net... > If it ain't the CV joint, either one, could be the "throw out bearing" > preceeding the clutch, at the clutch fork. > -- > Jonny > > wrote in message > oups.com... >> When I make a turn, of any radius, whith the clutch engaged, there is a >> clicking noise coming from the front of the car. Going straight, there >> is no sound, and if I disengage the clutch, the noise disappears.... >> >> Any ideas? >> > > |
#5
|
|||
|
|||
clicking noise on 99 VW Passat (6 Cyl) - only when clutch engaged
It sounds like you need to service your outer CV joints. You can do
one of two things. Pull the half shafts off, remove the clamps and boots, and degrease the joints. This should be done every 100,000 miles anyway. I even pull the joints off the half shafts and put them on the other shaft so they wear more evenly and last longer. Reinstall the boots, fill with the grease for that purpose, or use AMSOIL HD Grease with moly (one tube of GHD-CR on their web site), and reinstall the clamps. You're good for another 100,000 miles. The cheap and dirty solution is to put a needle fitting on your grease gun, shove the needle between the boot and half shaft from the engine side, and put several pumps of grease into the joint. You aren't servicing the joints by doing this but you are giving them much needed new lubrication. The first solution is the best if you plan on keeping your VW past 8 years. |
#6
|
|||
|
|||
clicking noise on 99 VW Passat (6 Cyl) - only when clutch engaged
That will work, great on CVs not clicking already. But is actually better
on Air-cooled VWs , not water cooled. Because they trash at 30,000 miles, not 100,000. But if they are clicking already they are worn ,not lacking grease. I wouldn't take off CV joints and lube and replace them with 100,000 miles on them. Maybe 10,000 and only because a boot tore and I caught it right away. They will probably start clicking within two months as soon as you move the grease around driving on them. Its a waste of time and energy. Id change them for the cost is not much for rebuilt shafts , verses putting new boots on old shafts with new grease. I,d think very hard about putting used shafts on a car if I had them off already. Also about putting used boots back on, Then about all the trouble cleaning them in solvent and regreasing them. Then doing it again in three months because they still click. Also if your needle fitting slips under the boot and clamp on your shaft. The clamps too loose. CVs work because the boot keeps grease in and dirt out. If you can grease them, you're screwed. grease the boot , Change the clamp . "Corrado Daddy" > wrote in message oups.com... > It sounds like you need to service your outer CV joints. You can do > one of two things. Pull the half shafts off, remove the clamps and > boots, and degrease the joints. This should be done every 100,000 > miles anyway. I even pull the joints off the half shafts and put them > on the other shaft so they wear more evenly and last longer. Reinstall > the boots, fill with the grease for that purpose, or use AMSOIL HD > Grease with moly (one tube of GHD-CR on their web site), and reinstall > the clamps. You're good for another 100,000 miles. > > The cheap and dirty solution is to put a needle fitting on your grease > gun, shove the needle between the boot and half shaft from the engine > side, and put several pumps of grease into the joint. You aren't > servicing the joints by doing this but you are giving them much needed > new lubrication. The first solution is the best if you plan on keeping > your VW past 8 years. > |
#7
|
|||
|
|||
clicking noise on 99 VW Passat (6 Cyl) - only when clutch engaged
If you don't mind doing the work yourself...............clean, inspect and
repack those CV Joints or replace the driveshafts. If someone else is doing the work and you don't mind spending the $$$ then have new/rebuilt driveshafts put on. Repacking those CV Joints might be fine! ;-) JMHO -- later, dave (One out of many daves) http://vwdoc1.tripod.com/ "none2u" > wrote in message et... > That will work, great on CVs not clicking already. But is actually better > on Air-cooled VWs , not water cooled. Because they trash at 30,000 miles, > not 100,000. But if they are clicking already they are worn ,not lacking > grease. I wouldn't take off CV joints and lube and replace them with > 100,000 miles on them. Maybe 10,000 and only because a boot tore and I > caught it right away. They will probably start clicking within two months > as soon as you move the grease around driving on them. Its a waste of time > and energy. Id change them for the cost is not much for rebuilt shafts , > verses putting new boots on old shafts with new grease. I,d think very > hard about putting used shafts on a car if I had them off already. Also > about putting used boots back on, Then about all the trouble cleaning them > in solvent and regreasing them. Then doing it again in three months > because they still click. Also if your needle fitting slips under the boot > and clamp on your shaft. The clamps too loose. CVs work because the boot > keeps grease in and dirt out. If you can grease them, you're screwed. > grease the boot , Change the clamp . > "Corrado Daddy" > wrote in message > oups.com... >> It sounds like you need to service your outer CV joints. You can do >> one of two things. Pull the half shafts off, remove the clamps and >> boots, and degrease the joints. This should be done every 100,000 >> miles anyway. I even pull the joints off the half shafts and put them >> on the other shaft so they wear more evenly and last longer. Reinstall >> the boots, fill with the grease for that purpose, or use AMSOIL HD >> Grease with moly (one tube of GHD-CR on their web site), and reinstall >> the clamps. You're good for another 100,000 miles. >> >> The cheap and dirty solution is to put a needle fitting on your grease >> gun, shove the needle between the boot and half shaft from the engine >> side, and put several pumps of grease into the joint. You aren't >> servicing the joints by doing this but you are giving them much needed >> new lubrication. The first solution is the best if you plan on keeping >> your VW past 8 years. >> > > |
#8
|
|||
|
|||
clicking noise on 99 VW Passat (6 Cyl) - only when clutch engaged
I have 165,000 miles on my front CV joints. No clicking ever by
servicing them at 100,000 mile intervals. Maybe it's the AMSOIL HD grease that makes the difference? I have never used the OE grease. My boots do not have a clamp on the half shaft side. It is easy to slip a needle fitting in there and add grease. No leaks there either. Mine is a 91 Jetta. My first (85) Jetta went 300,000 miles on the original CV joints. I saved them for a project car when I took the car out of service due to severe body rust where someone welded a new trunk on the back of the car. I still have the engine and tranny from that car too. Know where I can get a good, rust free 91 Jetta diesel body to put them in? Nothing like one of these for a commuter car that gets 50 mpg and lasts 10 years or more with a little TLC! No payments either! |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Q: Scarry noise - Passat 1990 | John Henderson | VW water cooled | 4 | March 7th 06 11:05 AM |
Scarry noise - Passat 1990 | stu katz | VW water cooled | 0 | March 5th 06 05:35 PM |
Road noise in the new 2006 Passat | William Maslin | VW water cooled | 3 | January 20th 06 11:50 PM |
tracking down clicking noise | DougW | Jeep | 4 | September 5th 05 06:50 AM |
Clicking sound from clutch pedal when depressed a little | [email protected] | Technology | 4 | July 31st 05 08:14 PM |