A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » BMW
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Blower on E39 stopped working



 
 
Thread Tools Display Modes
  #1  
Old October 30th 04, 11:45 AM
AlanG
external usenet poster
 
Posts: n/a
Default Blower on E39 stopped working

The blower on my 97 528 has stopped working. There is air coming through
(low volume) but when I select the screen demister or select a high fan
speed nothing happens. Any suggestions? The fuses seem fine. Is this a
home repair job?

Thanks for any help.

Alan G


Ads
  #2  
Old October 30th 04, 12:02 PM
Dave Plowman (News)
external usenet poster
 
Posts: n/a
Default

In article >,
AlanG > wrote:
> The blower on my 97 528 has stopped working. There is air coming through
> (low volume) but when I select the screen demister or select a high fan
> speed nothing happens. Any suggestions? The fuses seem fine. Is this a
> home repair job?


Assuming the display is still normal, the likely cause is the resistor
which controls the fan speed. It's a very common failure.

It's located between the heater and the bulkhead on the (UK) driver's
side. You need to remove the panel at the top of the driver's footwell,
and the carpet strip on the side of the transmission tunnel.

You can't see the unit - only the plug. Obtaining a new one before
starting will make identifying slightly easier. There's a clip you need to
depress before removing - a bit fiddly. An agile teenager (if you can find
one with the patience) might help. ;-)

IIRC, the part is called the final stage resistor and costs about 50 gbp.
Think it's a dealer only option, but worth trying Eurocarparts.

I've had three in my 528. The latest one has lasted best, so may be a
better design.

--
*Can fat people go skinny-dipping?

Dave Plowman London SW
To e-mail, change noise into sound.
  #3  
Old October 30th 04, 02:48 PM
Dave Plowman (News)
external usenet poster
 
Posts: n/a
Default

In article >,
> wrote:
> I've had similar problems on a citroen, the resistor is infact four
> heavy coils of wire which can be switched in series according to the fan
> switch. At the output there's a heavy duty diode.


> In my case the resistor pack was about forty quid or so, I had a look at
> it and checked the diode; it was open circuit. I replaced the diode for
> about fifty pence. No problems since.


I'd assumed I'd be able to repair the BMW one too, in some way. No chance.

It's all potted in a strange shaped metal case. I've heard it called a
hedgehog by some.

--
*If a parsley farmer is sued, can they garnish his wages?

Dave Plowman London SW
To e-mail, change noise into sound.
  #4  
Old October 31st 04, 11:08 AM
AlanG
external usenet poster
 
Posts: n/a
Default


"Dave Plowman (News)" > wrote in message
...
> In article >,
> AlanG > wrote:
>> The blower on my 97 528 has stopped working. There is air coming through
>> (low volume) but when I select the screen demister or select a high fan
>> speed nothing happens. Any suggestions? The fuses seem fine. Is this a
>> home repair job?

>
> Assuming the display is still normal, the likely cause is the resistor
> which controls the fan speed. It's a very common failure.
>
> It's located between the heater and the bulkhead on the (UK) driver's
> side. You need to remove the panel at the top of the driver's footwell,
> and the carpet strip on the side of the transmission tunnel.
>
> You can't see the unit - only the plug. Obtaining a new one before
> starting will make identifying slightly easier. There's a clip you need to
> depress before removing - a bit fiddly. An agile teenager (if you can find
> one with the patience) might help. ;-)


Thanks for the reply Dave. The display is working as normal. Why do you
think resistor rather than the fan unit? Is it because there is a low
volume of air coming through? Thanks. Alan


  #5  
Old October 31st 04, 11:28 AM
Dave Plowman (News)
external usenet poster
 
Posts: n/a
Default

In article >,
AlanG > wrote:
> Thanks for the reply Dave. The display is working as normal. Why do
> you think resistor rather than the fan unit? Is it because there is a
> low volume of air coming through? Thanks. Alan


Because it's a *very* common problem. The symptoms range from the blower
changing speed by itself, sticking on full, not working at all, and any
combinations thereof. ;-)

--
*If all is not lost, where the hell is it?

Dave Plowman London SW
To e-mail, change noise into sound.
  #6  
Old October 31st 04, 12:56 PM
AlanG
external usenet poster
 
Posts: n/a
Default


"Dave Plowman (News)" > wrote in message
...
> In article >,
> AlanG > wrote:
>> Thanks for the reply Dave. The display is working as normal. Why do
>> you think resistor rather than the fan unit? Is it because there is a
>> low volume of air coming through? Thanks. Alan

>
> Because it's a *very* common problem. The symptoms range from the blower
> changing speed by itself, sticking on full, not working at all, and any
> combinations thereof. ;-)


Yes! I recognise all these symptons. They occurred in the months prior to
the blower breaking down. Many thanks Dave.


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
'94 318is-clock And Temp Guage Has Stopped Working ultraviolet353 BMW 0 October 6th 04 01:37 AM
98 BMW 528i Wipers not working Michael & Yesenia Ruffin BMW 0 September 30th 04 11:07 PM
Smoke inside car whenever Im stopped.. Kev Edwards BMW 9 September 24th 04 07:42 PM
Rebuild Audi Blower motor? Kevin Audi 2 August 10th 04 11:34 PM
96 A6 blower regulation flaps gets stuck? (stays cold / warm / whatever) kons Audi 4 July 7th 04 11:29 PM


All times are GMT +1. The time now is 06:57 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.