If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
transmission mount on a CJ
Whats the best way to change one of these? I have a 76-cj5 and the shift
lever moves considerably when the engine is under a load. I was just wondering how to support things while the skid plate is removed..doesnt it hold the tranny and TC up? thanks guys! |
Ads |
#2
|
|||
|
|||
transmission mount on a CJ
Steve G did pass the time by typing:
> Whats the best way to change one of these? I have a 76-cj5 and the shift > lever moves considerably when the engine is under a load. > > I was just wondering how to support things while the skid plate is > removed..doesnt it hold the tranny and TC up? > > thanks guys! Probably close to what I do. http://revbeergoggles.com/motormount/ -- DougW |
#3
|
|||
|
|||
transmission mount on a CJ
"DougW" > wrote in news:qGLXf.8986$FD4.2177
@dukeread07: > Steve G did pass the time by typing: >> Whats the best way to change one of these? I have a 76-cj5 and the shift >> lever moves considerably when the engine is under a load. >> >> I was just wondering how to support things while the skid plate is >> removed..doesnt it hold the tranny and TC up? >> >> thanks guys! > > Probably close to what I do. > http://revbeergoggles.com/motormount/ > I actually had printed out that page for reference, a couple weeks ago, as I did mine. It was far more helpfull than the Chilton manual. Thanks, rufus |
#4
|
|||
|
|||
transmission mount on a CJ
I would be checking the engine mounts first. You can have someone watch
the engine as you let out the clutch in 1st while holding the brake down. Do the same in reverse. If the engine lifts on either, you have a busted mount. To check the tranny mount, I just lay under and lift and push on the tail piece to see if it moves around. It has an outrigger mount likely too. You can put a jack or axle stand under the tailpiece or right at the front of the tranny/skid plate to hold it up, but I shudder at the though of trying to remove a skid plate that old. Visions of grinding off nuts, spun nutserts and snapped bolts and welders keep going through my head.... I think I would try and undo the mount, then lift up on the tail piece to try and get the old mount to slide out. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) Steve G wrote: > > Whats the best way to change one of these? I have a 76-cj5 and the shift > lever moves considerably when the engine is under a load. > > I was just wondering how to support things while the skid plate is > removed..doesnt it hold the tranny and TC up? > > thanks guys! |
#5
|
|||
|
|||
transmission mount on a CJ
Thanks.. thinking about replacing all three mounts at same time to keep
every thing straight anyway. "Mike Romain" > wrote in message ... >I would be checking the engine mounts first. You can have someone watch > the engine as you let out the clutch in 1st while holding the brake > down. Do the same in reverse. If the engine lifts on either, you have > a busted mount. To check the tranny mount, I just lay under and lift > and push on the tail piece to see if it moves around. > > It has an outrigger mount likely too. > > You can put a jack or axle stand under the tailpiece or right at the > front of the tranny/skid plate to hold it up, but I shudder at the > though of trying to remove a skid plate that old. Visions of grinding > off nuts, spun nutserts and snapped bolts and welders keep going through > my head.... > > I think I would try and undo the mount, then lift up on the tail piece > to try and get the old mount to slide out. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's > Canadian Off Road Trips Photos: Non members can still view! > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > (More Off Road album links at bottom of the view page) > > Steve G wrote: >> >> Whats the best way to change one of these? I have a 76-cj5 and the shift >> lever moves considerably when the engine is under a load. >> >> I was just wondering how to support things while the skid plate is >> removed..doesnt it hold the tranny and TC up? >> >> thanks guys! |
#6
|
|||
|
|||
transmission mount on a CJ
Maybe four: http://www.billhughes.com/cj7stablizerMount.jpg
God Bless America, Bill O|||||||O Steve G wrote: > > Thanks.. thinking about replacing all three mounts at same time to keep > every thing straight anyway. |
#7
|
|||
|
|||
transmission mount on a CJ
Just be careful with the engine mounts. They are reverse of each other
on either side of the engine so their safety loop limits the sideways movement of the mount's rubber. That is so you can't just tear them apart first time you hit low range. I also highly recommend you get OEM mounts, not aftermarket ones. I totally destroy aftermarket mounts on mine. I literally shattered the last one. The rubber was still holding, but the metal plates were crumbled. Mike Steve G wrote: > > Thanks.. thinking about replacing all three mounts at same time to keep > every thing straight anyway. > > "Mike Romain" > wrote in message > ... > >I would be checking the engine mounts first. You can have someone watch > > the engine as you let out the clutch in 1st while holding the brake > > down. Do the same in reverse. If the engine lifts on either, you have > > a busted mount. To check the tranny mount, I just lay under and lift > > and push on the tail piece to see if it moves around. > > > > It has an outrigger mount likely too. > > > > You can put a jack or axle stand under the tailpiece or right at the > > front of the tranny/skid plate to hold it up, but I shudder at the > > though of trying to remove a skid plate that old. Visions of grinding > > off nuts, spun nutserts and snapped bolts and welders keep going through > > my head.... > > > > I think I would try and undo the mount, then lift up on the tail piece > > to try and get the old mount to slide out. > > > > Mike > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > > 88 Cherokee 235 BFG AT's > > Canadian Off Road Trips Photos: Non members can still view! > > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > > (More Off Road album links at bottom of the view page) > > > > Steve G wrote: > >> > >> Whats the best way to change one of these? I have a 76-cj5 and the shift > >> lever moves considerably when the engine is under a load. > >> > >> I was just wondering how to support things while the skid plate is > >> removed..doesnt it hold the tranny and TC up? > >> > >> thanks guys! |
#8
|
|||
|
|||
transmission mount on a CJ
I will see if I kept it when I go out tomorrow.
You know that metal plate that fell off the rubber part? Think that shattered into pieces still stuck to the rubber.... It is because of my tall gears, 3.31's and 33x9.5" muds that just don't spin. It stresses the crap out of the engine mounts and frame. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) Steve G wrote: > > Hey mike.. any chance youd have a pic of crumbled (metal plates) mounts? im > not sure i understand how you mean? > > I got my engine mounts in today.. gonna wait for weekend for the tranny. The > engine maounts seemed to have helped though. One of them fell in two pieces > when it came out. > > Thanks guys! |
#9
|
|||
|
|||
transmission mount on a CJ
Sounds similar to my 33x10.50 with 3.54's =)
i bet yours has better low range than the dana20 TC though... "Mike Romain" > wrote in message ... >I will see if I kept it when I go out tomorrow. > > You know that metal plate that fell off the rubber part? Think that > shattered into pieces still stuck to the rubber.... > > It is because of my tall gears, 3.31's and 33x9.5" muds that just don't > spin. It stresses the crap out of the engine mounts and frame. > |
#10
|
|||
|
|||
transmission mount on a CJ
I posted a couple photos over on alt.binaries.pictures.autos.4x4
My 258 is manually tuned up with an Accel Supercoil and a straight pipe to a Dynomax Turbo muffler. It is tuned to pass emissions with nice numbers despite not needing a Cat converter. I will light up the 33's from a start, hit 52 mph at 4400 rpm in 2nd, a quick 75 mph in 3rd, 4th buries the speedo and I have no urge to see how fast 5th will go..... Mike Steve G wrote: > > Hey mike.. any chance youd have a pic of crumbled (metal plates) mounts? im > not sure i understand how you mean? > > I got my engine mounts in today.. gonna wait for weekend for the tranny. The > engine maounts seemed to have helped though. One of them fell in two pieces > when it came out. > > Thanks guys! |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Caravan Transmission Replacement by DIY?? | dprkk | Chrysler | 18 | February 3rd 06 07:34 AM |
Transmission problems | ozymandias | Technology | 2 | January 10th 06 01:28 AM |
Transmission Problem? | ozymandias | Technology | 1 | January 9th 06 03:10 PM |
Transmission probelms | ozymandias | Technology | 0 | January 8th 06 11:28 PM |
Transmission removal and engine mount questions... | TeGGer® | Honda | 7 | April 11th 05 08:32 PM |