If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
'97 Accord EX Coupe Rust Analysis
I'm looking at a '96 Accord EX Coupe. It's exactly the car I'm after, and in
solid condition, however... I discovered rust when inspecting the rear undercarriage. I need some help analyzing whether this is a serious enough issue to disqualify the car. I will do my best to describe where the rust is. Under the rear of the car, set in 3-6 inches from where the bumper goes under the car is a piece of steel attached to the undercarriage that spans almost the entire wheel base. From what I recall, it is something like 4-5 inches wide, and 1/2" thick. I would say that this piece of steel is moderately rusted. Mostly on the passenger-side edge. I can get a good deal on the car, but I want to get another 75-100K out of it without it rusting out and becoming a safety hazard. I need something that will become mechanically untenable before body and frame issues come into play. |
Ads |
#2
|
|||
|
|||
On Fri, 31 Dec 2004 08:05:04 -0700, "SmarSquid"
> wrote: >I'm looking at a '96 Accord EX Coupe. It's exactly the car I'm after, and in >solid condition, however... I discovered rust when inspecting the rear >undercarriage. I need some help analyzing whether this is a serious enough >issue to disqualify the car. >I will do my best to describe where the rust is. Under the rear of the car, >set in 3-6 inches from where the bumper goes under the car is a piece of >steel attached to the undercarriage that spans almost the entire wheel base. >From what I recall, it is something like 4-5 inches wide, and 1/2" thick. Sounds like you're describing a rear suspension member. >I would say that this piece of steel is moderately rusted. Mostly on the >passenger-side edge. Rusted how? Surface rust? Eaten through with holes? Use a screwdriver to poke at it. Does the screwdriver go right through? >I can get a good deal on the car, but I want to get another 75-100K out of >it without it rusting out and becoming a safety hazard. I need something >that will become mechanically untenable before body and frame issues come >into play. Where are you? Is there salt on the roads in winter? Did you check the tops of the strut towers under the hood for rust? That's a frequent Honda rust disaster area. Also the doorsills, especially around the jacking points. Check the floorboards where water from footwear has soaked the carpet. |
#3
|
|||
|
|||
It certainly appears to be surface rust, but further analysis (pokes and
prods) is necessary before I would know whether or not the metal could be perforated or crushed. The car has always been in Colorado (my home state), according to the Carfax data. So, yes, salted roads are a seasonal variable in play here. I will also check the strut towers, but I am hopeful that you could give me further feedback on how to identify this area/these parts. Where exactly they are, and a basic description of what it looks like. I'm not all that mechanically inclined, and suspension components are a specific weakness for me. Floorboards and jack points - I can handle that. I also have close friends in the body shop industry. They may be able to offer feedback as well, but I am wondering how easy it is for someone like that to look at an existing car and extrapolate with reasonable accuracy what is likely to occur going forward. "John Ings" > wrote in message ... > On Fri, 31 Dec 2004 08:05:04 -0700, "SmarSquid" > > wrote: > >>I'm looking at a '96 Accord EX Coupe. It's exactly the car I'm after, and >>in >>solid condition, however... I discovered rust when inspecting the rear >>undercarriage. I need some help analyzing whether this is a serious enough >>issue to disqualify the car. >>I will do my best to describe where the rust is. Under the rear of the >>car, >>set in 3-6 inches from where the bumper goes under the car is a piece of >>steel attached to the undercarriage that spans almost the entire wheel >>base. >>From what I recall, it is something like 4-5 inches wide, and 1/2" thick. > > Sounds like you're describing a rear suspension member. > >>I would say that this piece of steel is moderately rusted. Mostly on the >>passenger-side edge. > > Rusted how? Surface rust? Eaten through with holes? Use a screwdriver > to poke at it. Does the screwdriver go right through? > >>I can get a good deal on the car, but I want to get another 75-100K out of >>it without it rusting out and becoming a safety hazard. I need something >>that will become mechanically untenable before body and frame issues come >>into play. > > Where are you? Is there salt on the roads in winter? > > Did you check the tops of the strut towers under the hood for rust? > That's a frequent Honda rust disaster area. Also the doorsills, > especially around the jacking points. Check the floorboards where > water from footwear has soaked the carpet. > > > > |
#4
|
|||
|
|||
On Fri, 31 Dec 2004 09:22:30 -0700, "SmarSquid"
> wrote: >It certainly appears to be surface rust, but further analysis (pokes and >prods) is necessary before I would know whether or not the metal could be >perforated or crushed. The car has always been in Colorado (my home state), >according to the Carfax data. So, yes, salted roads are a seasonal variable >in play here. I lived in Denver for a year in 1969-70 and hardly saw any snow, but westward in the mountains there's sure lots, and eastward some too. So it would depend on just where the car was driven in Colorado. > >I will also check the strut towers, but I am hopeful that you could give me >further feedback on how to identify this area/these parts. Where exactly >they are, and a basic description of what it looks like. I'm not all that >mechanically inclined, and suspension components are a specific weakness for >me. Above the front wheels are MacPherson struts, essentially shock absorbers with coil springs around them, or if the car uses torsion bars, just shock absorbers. If you look under the hood on the right and left sides near the firewall, you will see that the bodywork bulges upward there, and there is a big nut and washer right in the middle of this bulge. That's the top mounting nut for the shock absorber. Often this tower, which is an integral part of the bodywork, rusts out from the underside. >Floorboards and jack points - I can handle that. Note that doorsills are hidden from topside inspection by plastic covers these days. Get the car up on a hoist and poke with that screwdriver from underneath. >I also have close friends in the body shop industry. They may be able to >offer feedback as well, but I am wondering how easy it is for someone like >that to look at an existing car and extrapolate with reasonable accuracy >what is likely to occur going forward. Any experienced bodyman should be able to do so, having been informed where YOU are going to be driving. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Make 2001 Accord Coupe Headlights brighter | Will | Honda | 1 | December 29th 04 05:39 PM |
2001 Accord Coupe Rear Rotor Replacement | Lucas Tam | Honda | 16 | November 30th 04 04:15 AM |
90 accord coupe | saki | Honda | 1 | November 14th 04 11:30 AM |
FA: 1995 Honda Accord Coupe - Clean but needs some Paint - Until Sunday. | Scott Peteres | Honda | 1 | September 24th 04 06:55 PM |