If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Oh boy... what fun. :)
Just finished putting a new CV boot on my ZJ.
Not terribly hard, except for those three damn bearing to knuckle bolts that managed to break two of my el-cheapo sockets and required some back-woods engineering. (Had to put a jack under the breaker bar to get enough force to break the forward bolt free) Impressive for bolts that only go in to 75ft.lbs. But that was almost 13 years ago. Yep.. took photos. Gonna be a while before I can get them on-line or do a write-up. Only thing that bugs me is I think I didn't get enough air out of the boot, it's not as flat as the other side. But then again the silly boot only costs $11 so if it goes again I'll take another crack at it. Hmm... I might be able to get a new band clamp and just cut the old one off, burp it, and reclamp. Hibdon tires (who spotted the problem while doing my rotation/balance) wanted to charge $460 to half-shaft the axle. Kept on telling me how hard the job is. Jeep wanted over 80$ for the stupid boot. NAPA, as usual, came through at $11. In reality it's one of the dirtiest jobs I've ever done on the ZJ. Lots of grease everywhere, dirt to haul out of the axle, and cleaning the CV joint.. -- DougW |
Ads |
#2
|
|||
|
|||
Oh boy... what fun. :)
What are you going to do with the $449. you saved?
How does it rate on your beer scale? "DougW" > wrote in message news:5PrMg.10193$JR5.5754@dukeread11... > Just finished putting a new CV boot on my ZJ. > > Not terribly hard, except for those three damn > bearing to knuckle bolts that managed to break > two of my el-cheapo sockets and required some > back-woods engineering. (Had to put a jack under > the breaker bar to get enough force to break the > forward bolt free) Impressive for bolts that only > go in to 75ft.lbs. But that was almost 13 years ago. > > Yep.. took photos. Gonna be a while before > I can get them on-line or do a write-up. > > Only thing that bugs me is I think I didn't > get enough air out of the boot, it's not as > flat as the other side. But then again the > silly boot only costs $11 so if it goes again > I'll take another crack at it. > > Hmm... I might be able to get a new band clamp > and just cut the old one off, burp it, and reclamp. > > Hibdon tires (who spotted the problem while doing > my rotation/balance) wanted to charge $460 to half-shaft > the axle. Kept on telling me how hard the job is. > Jeep wanted over 80$ for the stupid boot. NAPA, as usual, > came through at $11. > > In reality it's one of the dirtiest jobs I've ever done > on the ZJ. Lots of grease everywhere, dirt to haul out > of the axle, and cleaning the CV joint.. > > -- > DougW > |
#3
|
|||
|
|||
Oh boy... what fun. :)
Hi Doug,
Looking forward to your documentation, your pages: http://members.cox.net/wilsond/ are very helpful. God Bless America, Bill O|||||||O http://www.billhughes.com/ DougW wrote: > > Just finished putting a new CV boot on my ZJ. > > Not terribly hard, except for those three damn > bearing to knuckle bolts that managed to break > two of my el-cheapo sockets and required some > back-woods engineering. (Had to put a jack under > the breaker bar to get enough force to break the > forward bolt free) Impressive for bolts that only > go in to 75ft.lbs. But that was almost 13 years ago. > > Yep.. took photos. Gonna be a while before > I can get them on-line or do a write-up. > > Only thing that bugs me is I think I didn't > get enough air out of the boot, it's not as > flat as the other side. But then again the > silly boot only costs $11 so if it goes again > I'll take another crack at it. > > Hmm... I might be able to get a new band clamp > and just cut the old one off, burp it, and reclamp. > > Hibdon tires (who spotted the problem while doing > my rotation/balance) wanted to charge $460 to half-shaft > the axle. Kept on telling me how hard the job is. > Jeep wanted over 80$ for the stupid boot. NAPA, as usual, > came through at $11. > > In reality it's one of the dirtiest jobs I've ever done > on the ZJ. Lots of grease everywhere, dirt to haul out > of the axle, and cleaning the CV joint.. > > -- > DougW |
#4
|
|||
|
|||
Oh boy... what fun. :)
billy ray wrote:
> What are you going to do with the $449. you saved? Probably blow it all on new tools that don't shatter when I use them. http://www.revbeergoggles.com/temp/b0rk-sockets.jpg > How does it rate on your beer scale? Tecnically it's a very easy job. Just bolts and having a banding clamp tool. But those bolts are a PITA so I would rate it about three beers. Two if you have an air wrench or strong arms. -- DougW |
#5
|
|||
|
|||
Oh boy... what fun. :)
Made in Red China?
"DougW" > wrote in message news:EZzMg.10199$JR5.605@dukeread11... > billy ray wrote: >> What are you going to do with the $449. you saved? > > Probably blow it all on new tools that don't shatter > when I use them. > http://www.revbeergoggles.com/temp/b0rk-sockets.jpg > > >> How does it rate on your beer scale? > > Tecnically it's a very easy job. Just bolts > and having a banding clamp tool. But those > bolts are a PITA so I would rate it about > three beers. Two if you have an air wrench > or strong arms. > > > -- > DougW > |
#6
|
|||
|
|||
Oh boy... what fun. :)
billy ray wrote:
> Made in Red China? Taiwan. Like all qwality tools are. Actually I have several sets of tools. Some real good craftsman/snap-on/s&k and an assortment of crap that I don't mind loaning out. This is yet another fine opportunity to buy some more good sockets. > "DougW" wrote ... >> billy ray wrote: >>> What are you going to do with the $449. you saved? >> >> Probably blow it all on new tools that don't shatter >> when I use them. >> http://www.revbeergoggles.com/temp/b0rk-sockets.jpg |
#7
|
|||
|
|||
Oh boy... what fun. :)
"DougW" > wrote in message
news:P1BMg.10200$JR5.2621@dukeread11... ---snippy--- > > Actually I have several sets of tools. Some real good craftsman/snap-on/s&k > and an assortment of crap that I don't mind loaning out. This is yet another > fine opportunity to buy some more good sockets. > I'll remember that the next time I want to round off some bolt heads. ;^) SK sockets used to break. Do they still do that? Earle |
#8
|
|||
|
|||
Oh boy... what fun. :)
Earle Horton wrote:
> "DougW" wrote >> Actually I have several sets of tools. Some real good >> craftsman/snap-on/s&k and an assortment of crap that I don't mind >> loaning out. This is yet another fine opportunity to buy some more >> good sockets. >> > I'll remember that the next time I want to round off some bolt heads. > ;^) I've got the perfect socket set for that and I'll even throw in the plumbers wrench so you can rip the head right off that bolt. > SK sockets used to break. Do they still do that? I've never had an SK socket break on me, but I have twisted the ends off several extensions and adapters with them. They are the black (impact) type. -- DougW |
#9
|
|||
|
|||
Oh boy... what fun. :)
"DougW" > wrote in message
news:HqCMg.10218$JR5.3977@dukeread11... > Earle Horton wrote: > > "DougW" wrote > > >> Actually I have several sets of tools. Some real good > >> craftsman/snap-on/s&k and an assortment of crap that I don't mind > >> loaning out. This is yet another fine opportunity to buy some more > >> good sockets. > >> > > I'll remember that the next time I want to round off some bolt heads. > > ;^) > > I've got the perfect socket set for that and I'll even throw in the > plumbers wrench so you can rip the head right off that bolt. > > > SK sockets used to break. Do they still do that? > > I've never had an SK socket break on me, but I have twisted the ends > off several extensions and adapters with them. They are the black > (impact) type. > I stopped buying them about thirty years ago, when a salesman told me that the cheap ass rubber handle on a breaker bar fell off the breaker bar, because I had abused it. Then a counter person told me that I would have to take a broken socket back to the store where I had bought it, six states away. The shiny ones were famous for shattering, but they didn't round off bolt heads. I still have an SK metal socket organizer, full of mostly Craftsman sockets! The wrenches were tough, but too big for most uses. Earle |
#10
|
|||
|
|||
Oh boy... what fun. :)
DON'T USE NO NAME TOOLS! Not even it they were a gift!
God Bless America, Bill O|||||||O http://www.billhughes.com/ DougW wrote: > > Probably blow it all on new tools that don't shatter > when I use them. > http://www.revbeergoggles.com/temp/b0rk-sockets.jpg > > Tecnically it's a very easy job. Just bolts > and having a banding clamp tool. But those > bolts are a PITA so I would rate it about > three beers. Two if you have an air wrench > or strong arms. > > -- > DougW |
Thread Tools | |
Display Modes | |
|
|